This calculator finds the mass of sodium hydroxide (NaOH) needed for a 1 mol/L solution with a final volume of 100 mL. Enter the target molarity and final volume to get the required NaOH mass, plus the amount of substance in moles.
Formula
Mass equals molarity multiplied by final volume in liters and molar mass: m = C × (V / 1000) × M. Here, m is NaOH mass in grams, C is target concentration in mol/L, V is final solution volume in mL, and M is the molar mass in g/mol. Dividing V by 1000 converts milliliters to liters. The amount of substance is n = C × (V / 1000), in moles.
The default molar mass, 39.997 g/mol, is calculated from the abridged standard atomic weights Na = 22.990, O = 15.999, and H = 1.008. These sum to 39.997 g/mol. The calculator assumes the stated NaOH is pure; actual reagent purity and moisture can change the mass needed for a precise laboratory solution.
Worked Example
Using the defaults, C = 1 mol/L, V = 100 mL, and M = 39.997 g/mol.
First convert the volume: 100 mL / 1000 = 0.10000 L.
Then find the amount: n = 1 mol/L × 0.10000 L = 0.1000 mol.
Finally find the mass: m = 1 mol/L × (100 mL / 1000) × 39.997 g/mol = 3.9997 g, which rounds to 4.000 g NaOH at the calculator’s three-decimal display precision.
Assumptions
- The target is a nominal 1 mol/L concentration, and volume means final solution volume, not the volume of water used at the start.
- NaOH is treated as pure, with complete dissociation assumed for concentration arithmetic; the calculator does not determine pH or activity.
- The formula is a study and lab-planning calculation, not a substitute for a validated method, purity correction, or volumetric technique.
What “1 M NaOH in 100 mL” Means
Molarity is the number of moles of solute per liter of final solution. Therefore, 100 mL of a 1 M solution contains 0.100 mol NaOH. Since one mole of NaOH has a mass of about 39.997 g, that amount corresponds to about 4.000 g. The intended result is a solution whose total volume is 100 mL after the solute has dissolved and the solution has been brought to its final volume.
It does not mean adding 4.000 g of solid to exactly 100 mL of water. Dissolved material contributes to the final volume, so that approach can produce more than 100 mL and a concentration below the intended value. For exact concentration, use the final-volume definition and account for the stated reagent purity where appropriate.
When to Use This Calculator
Use it to check the mass for a requested molarity and final volume in general chemistry coursework or lab planning. It can also be adapted to another concentration or volume by changing the inputs. Keep the units as shown: mol/L for concentration, mL for volume, and g/mol for molar mass. If your target is expressed in mmol/L, convert it to mol/L before entering it; 1000 mmol/L equals 1 mol/L.
The result is a calculated theoretical mass. Sodium hydroxide is hygroscopic and can absorb water and carbon dioxide from air, so an opened solid may not have the assumed composition. For work requiring a verified concentration, use the laboratory’s approved preparation and standardization method rather than treating the calculation as proof of concentration. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Practical Safety and Measurement Notes
Sodium hydroxide is corrosive and can cause severe skin and eye injury. Handle it only in an appropriate supervised laboratory setting with the protective equipment and controls specified by the SDS and local procedure. Dissolution releases heat, so do not assume the mixture will remain cool or that the final volume can be measured accurately while it is warm. The calculator provides arithmetic only; it is not a preparation protocol or a safety assessment.
Read a balance to the precision your method requires, and avoid rounding intermediate values unnecessarily. This example gives 3.9997 g from the selected molar mass, displayed as 4.000 g. If the reagent label gives a purity below 100%, a simple mass correction may be relevant mathematically, but the acceptable correction and verification depend on the method and intended accuracy.
Common Calculation Mistakes
- Using 100 instead of 0.100 L: the calculator converts mL to L explicitly; omitting that conversion makes the answer 1000 times too large.
- Confusing solute mass with solution volume: 4.000 g is the approximate NaOH mass, while 100 mL is the desired final solution volume.
- Using a different formula mass without checking: the listed value is for NaOH from standard atomic weights; a different compound or hydrate needs its own molar mass.
- Assuming nominal mass guarantees exact molarity: purity, absorbed moisture, temperature, and measurement uncertainty affect the actual result.
How to Use This List
This page is a calculator, so select the values that match your calculation rather than treating the example as a universal recipe. Set concentration in mol/L, enter the intended final volume in mL, and use the molar mass of the actual solute. Check that the output is in grams and that the volume entered is the final solution volume. For the specific case of 1 M and 100 mL, the calculated mass is approximately 4.000 g NaOH.
Frequently Asked Questions
How many grams of NaOH are in 100 mL of 1 M solution?
About 4.000 g, calculated using a molar mass of 39.997 g/mol.
How many moles does that represent?
It represents 0.100 mol, because 1 mol/L × 0.100 L = 0.100 mol.
Should I add the NaOH to 100 mL of water?
No. The target is 100 mL of final solution, not 100 mL of starting water; follow the approved lab method for reaching final volume.
Why might the actual concentration differ?
NaOH can absorb moisture and carbon dioxide, and weighing or volume-measurement errors also affect concentration.
Does the calculation account for reagent purity?
No. It assumes pure NaOH; use the method’s specified purity correction and verification for quantitative work.
Final Thoughts
For a nominal 1 M NaOH solution with a final volume of 100 mL, the stoichiometric calculation gives 0.100 mol, or about 4.000 g NaOH. The key distinction is final solution volume: concentration is defined after the solute is included, while safe handling and validated laboratory practice remain essential.
Related
Formula used
in c | Target molarity | mol/L | 1 | 0 in v | Final solution volume | mL | 100 | 0 in mm | Molar mass of NaOH | g/mol | 39.997 | 0.001 out m | NaOH mass | g | c * (v / 1000) * mm | 3 out n | Amount of NaOH | mol | c * (v / 1000) | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- PCR Primer Tm Calculation: How to Compute It
- Molecules to Moles Conversion Steps1.0000 mol
- Mean Rate of Reaction: How to Calculate It0.0050 mol/s
- Propane Vapor Pressure Calculator178.7 kPa
- mRNA vs Mature mRNA: Key Differences4,750
- Mass Fraction to Mole Fraction Calculator0.5195 fraction