molecalculator

Moles & Molar Mass

10% Glucose in Water by Mass: What It Means

Calculator No. 01-9815 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This article explains what a 10% glucose in water by mass solution means, how to prepare it, and how to convert between mass percent, molarity, and other concentration units. It is written for students, lab technicians, and anyone who needs to understand or make this common biological and chemical reagent.

Formula

The mass percent concentration (w/w) is defined as:

% (w/w) = (mass of solute / mass of solution) × 100

For a 10% glucose solution, 10 g of glucose is dissolved in enough water to make a total mass of 100 g of solution (i.e., 10 g glucose + 90 g water). The molarity (M) is calculated from the mass of solute, its molar mass, and the final volume of the solution:

M = (mass in grams / molar mass) / (volume in liters)

Where mass is in grams (g), molar mass in grams per mole (g/mol), and volume in liters (L). The calculator above computes molarity from the mass of solute, molar mass, and final solution volume.

Worked Example

Using the default values: 2.922 g of sodium chloride (NaCl, molar mass 58.44 g/mol) dissolved in enough water to make 250 mL of solution.

Step 1: Convert volume to liters: 250 mL = 250 / 1000 = 0.250 L

Step 2: Calculate moles of solute: 2.922 g / 58.44 g/mol = 0.05000 mol

Step 3: Calculate molarity: 0.05000 mol / 0.250 L = 0.2000 mol/L

So the molarity is 0.2000 M (or 200.0 mM). This matches the calculator output.

Assumptions

  • The solute is pure and completely dissolves.
  • The final volume is measured after dissolution, not the volume of solvent added.
  • Temperature is assumed to be around 25 °C for density conversions, but molarity calculations do not depend on temperature.
  • For mass percent, the density of water is taken as 1.00 g/mL for approximate conversions, but exact preparation uses mass measurements.

What Does 10% Glucose in Water by Mass Signify?

A 10% glucose solution by mass (w/w) contains 10 grams of glucose per 100 grams of solution. This is a common concentration used in biochemistry, microbiology, and clinical settings. It is often used as a carbon source in culture media, as a standard for osmotic pressure studies, or as a calibration standard for glucose assays. The key point is that the percentage is based on mass, not volume, so it is temperature-independent and precise when prepared by weighing both solute and solvent.

How to Prepare a 10% Glucose Solution

To prepare 100 g of 10% glucose solution, weigh 10 g of anhydrous D-glucose (C6H12O6, molar mass 180.156 g/mol) and dissolve it in about 80 mL of distilled water. After complete dissolution, adjust the total mass to 100 g by adding more water. This ensures the mass percent is exactly 10%. If you need a specific volume, use the density of the solution (approximately 1.034 g/mL at 20 °C for 10% glucose) to convert between mass and volume.

Molarity of 10% Glucose

The molarity of a 10% (w/w) glucose solution depends on the density of the solution. For a density of 1.034 g/mL, 100 g of solution has a volume of 96.7 mL (100 / 1.034). The moles of glucose in 100 g of solution are 10 g / 180.156 g/mol = 0.0555 mol. Thus, molarity = 0.0555 mol / 0.0967 L = 0.574 M. This is approximately 0.57 M. Always check the density of your specific solution for accurate conversions.

Common Mistakes

One common mistake is confusing mass percent (w/w) with volume percent (v/v) or mass/volume percent (w/v). A 10% w/v solution would be 10 g of glucose in 100 mL of solution, which is different from 10% w/w. Another mistake is using the volume of solvent instead of the final solution volume when calculating molarity. Always measure the final volume after dissolving the solute. Also, when preparing by mass, do not simply add 10 g to 100 mL of water; that gives a mass percent of approximately 9.1%, not 10%.

Applications of 10% Glucose

In microbiology, 10% glucose is often used in fermentation media to provide a high carbon source. In clinical laboratories, it may be used as a standard for glucose tolerance tests or as a calibration solution for glucometers. In biochemistry, it is used in osmotic stress experiments because it creates a defined osmotic pressure. It is also a common reagent in molecular biology for preparing competent cells or as a cryoprotectant in some protocols.

How to Choose

When choosing a concentration unit, consider your application. If you need to prepare a solution by weighing, mass percent is the most accurate and reproducible. If you are using volumetric glassware and need a specific molarity, calculate the required mass using the molar mass and final volume. For biological assays, molarity is often preferred because reactions depend on the number of molecules. Always verify the density of your glucose solution if converting between mass and volume, as it varies with temperature and concentration.

Frequently Asked Questions

Q: Is 10% glucose the same as 10 g per 100 mL?
A: Not exactly. 10% w/w means 10 g per 100 g of solution. If you add 10 g to 100 mL of water, the total mass is about 110 g, so the mass percent is about 9.1%. For 10% w/v, you would dissolve 10 g in enough water to make 100 mL final volume.

Q: What is the molarity of 10% glucose?
A: Approximately 0.57 M, assuming a density of 1.034 g/mL. The exact value depends on the density, which changes with temperature.

Q: Can I use glucose monohydrate instead of anhydrous glucose?
A: Yes, but you must account for the water of hydration. Glucose monohydrate (C6H12O6·H2O) has a molar mass of 198.17 g/mol, so you need to weigh more to get the same amount of anhydrous glucose.

Q: How do I make 500 mL of 10% w/v glucose?
A: Weigh 50 g of glucose, dissolve in about 400 mL of water, then bring the final volume to 500 mL in a volumetric flask.

Q: Does temperature affect the concentration?
A: Mass percent does not change with temperature because it is based on mass. Molarity changes slightly because volume changes with temperature, but the effect is small for dilute solutions.

Final Thoughts

Understanding what 10% glucose in water by mass means is essential for accurate solution preparation. Always specify whether you mean w/w, w/v, or v/v, and use the correct formula for your needs. The calculator above helps you convert between mass and molarity for any solute, not just glucose. Remember to follow your lab’s protocols and safety data sheets when handling chemicals.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →