molecalculator

Moles & Molar Mass

Absorbance and Concentration: Beer–Lambert Law

Calculator No. 01-5307 · Updated · Formula and assumptions shown below

Concentration 5.000 × 10−5 mol/L
Concentration
50.000 µmol/L
= Concentration × 1000000
Predicted absorbance
0.500000
= Molar absorptivity × Concentration × Path length
Absorbance
0.5
Set in the form below
You enter
Absorbance, Path length (cm), Molar absorptivity (L/(mol·cm))
You get
Concentration (mol/L), Concentration (µmol/L), Predicted absorbance
Rounding
6 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Absorbance is directly proportional to concentration when a substance obeys the Beer–Lambert law and the measurement conditions are controlled. This calculator uses absorbance, path length, and molar absorptivity to calculate concentration, or uses concentration to predict absorbance.

Formula

The Beer–Lambert law is A = εlc: absorbance equals molar absorptivity multiplied by path length and concentration. Rearranging gives c = A / (εl), the formula used for the calculator’s first result.

  • A is absorbance, dimensionless (often reported as absorbance units, AU).
  • ε is molar absorptivity, in L/(mol·cm), at the selected wavelength and under specified chemical conditions.
  • l is the optical path length through the sample, in cm.
  • c is concentration, in mol/L.

The inputs must use the units shown. In this calculator, absorbance is entered as a measured number, path length in centimetres, and molar absorptivity in L/(mol·cm). The equation then returns mol/L. The second output converts that concentration to µmol/L using 1 mol/L = 1,000,000 µmol/L. The final output calculates the absorbance implied by the calculated concentration; it should match the entered absorbance apart from rounding.

Worked Example

Using the default values—absorbance 0.500, path length 1 cm, and molar absorptivity 10,000 L/(mol·cm)—calculate concentration:

c = A / (εl)
c = 0.500 / (10,000 × 1 cm)
c = 0.500 / 10,000 = 0.000050000 mol/L
c = 0.000050 mol/L (6 decimal places)

Convert to micromolar: 0.000050000 mol/L × 1,000,000 = 50.000 µmol/L. The predicted absorbance is 10,000 × 0.000050000 × 1 = 0.500000, or 0.500000 at six decimal places.

Assumptions

  • The sample is sufficiently dilute and homogeneous for Beer–Lambert behavior over the measurement range.
  • Absorbance, path length, and molar absorptivity refer to the same wavelength and compatible measurement conditions.
  • The entered path length is the distance light travels through the sample, not the container’s outside width.
  • The molar absorptivity is appropriate for the chemical form being measured, including relevant solvent, pH, and temperature conditions.

Why Absorbance Tracks Concentration

A sample absorbs some of the light passing through it. In a typical absorbance measurement, the instrument compares the light intensity reaching the detector through the sample, I, with the intensity through a reference, I0. Transmittance is T = I/I0, and absorbance is A = −log10(T). Absorbance therefore increases as less light is transmitted.

For a suitable absorbing species, increasing the number of absorbing molecules in the light path increases absorbance in proportion to concentration. A longer path also gives light more material to pass through, so absorbance is proportional to path length as well. Molar absorptivity captures how strongly a particular substance absorbs at a particular wavelength. It is not a universal constant for all substances or all measurement conditions.

The law describes a linear relationship: if ε and l stay fixed, doubling c doubles A. For example, with ε = 10,000 L/(mol·cm) and l = 1 cm, a concentration of 0.000050 mol/L predicts A = 0.500; 0.000100 mol/L predicts A = 1.000. This proportionality is useful for estimating unknown concentrations from measured absorbance.

Using the Calculator and Choosing Inputs

Use this calculation when you have an absorbance reading and a suitable molar absorptivity for the measured species and wavelength. The most important judgment is often not the arithmetic but whether ε applies to your sample and whether the measurement is in the linear range.

  1. Enter the sample’s measured absorbance. Use the instrument’s absorbance value after the appropriate blank or reference correction.
  2. Enter the optical path length in centimetres. A standard 1 cm path is common, but other cells or measurement geometries may differ.
  3. Enter molar absorptivity in L/(mol·cm), from a reliable reference for the compound and measurement conditions, or from an appropriate calibration.
  4. Read the first result as mol/L. Use the micromolar output when that scale is more convenient, and check that the predicted absorbance agrees with the input.

For instance, if a sample was diluted before measurement, the calculator returns the concentration in the measured diluted sample. To infer the original concentration, multiply by the total dilution factor, provided the dilution was measured accurately and the sample remained stable. Do not treat an arbitrary literature ε as suitable merely because the compound name matches; wavelength, solvent, ionization state, and chemical environment can affect absorption.

When the Relationship Is Not Linear

Beer–Lambert law is a model, not a guarantee that every reading converts exactly to concentration. At high concentrations, interactions between molecules and changes in refractive properties can produce departures from linearity. Instrument effects, stray light, broad or mismatched spectral bands, scattering, and an unsuitable blank can also distort absorbance.

In mixtures, absorbances can add under suitable conditions, but a single absorbance reading generally cannot identify multiple unknown concentrations by itself. Each absorbing substance may contribute at the selected wavelength. Measurements at multiple wavelengths, a validated calibration curve, or another analytical method may be needed to distinguish components.

When ε is unknown or the system is not reliably described by the law, prepare or obtain standards of known concentration and measure them under the same conditions. Plot absorbance against concentration and use the linear portion of the calibration curve. A nonzero intercept or curvature can signal blank problems, matrix effects, or a limited linear range; it should not be ignored simply to force the data through the origin.

Common Mistakes and Practical Checks

  • Mixing units: Entering path length in millimetres while treating it as centimetres changes the answer by a factor of ten. Convert before using the formula.
  • Using the wrong ε: Molar absorptivity depends on wavelength and conditions. Confirm its units and the species to which it applies.
  • Confusing absorbance with transmittance: A transmittance fraction such as 0.50 is not absorbance 0.50. Convert using A = −log10(T); 50% transmittance corresponds to absorbance about 0.301.
  • Ignoring dilution: The result describes the sample actually measured, not automatically the sample before dilution.
  • Overinterpreting digits: Six calculator decimal places do not imply six-digit experimental accuracy. Precision is limited by the measurement, ε, path length, and sample preparation.

For laboratory work, confirm that the blank, wavelength, and sample handling match the method, and check that readings fall within a validated linear range. Follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

Is absorbance directly proportional to concentration?
Yes, under Beer–Lambert conditions, with path length and molar absorptivity fixed. The relationship may depart from linearity at high concentrations or when measurement conditions are unsuitable.

What is the formula for concentration from absorbance?
Rearrange A = εlc to get c = A/(εl). Use absorbance as a dimensionless value, ε in L/(mol·cm), and path length in cm to obtain concentration in mol/L.

Does higher absorbance mean higher concentration?
Usually, if the same substance is measured at the same wavelength with the same path length and conditions. A change in path length or chemical form can also change absorbance, so the comparison is meaningful only when those factors are controlled.

Can absorbance be greater than 1?
Yes. An absorbance of 1 corresponds to 10% transmittance, and larger absorbance corresponds to still lower transmittance. Very high readings may be less reliable because instrument limitations can affect the measurement.

Why is my calculated concentration negative or implausible?
This calculator rejects negative inputs, but a small or negative blank-corrected absorbance can arise from measurement noise or blank mismatch. A plausible concentration also depends on valid ε, units, dilution correction, and whether the sample follows a linear calibration range.

Related

Formula used
in a | Absorbance | - | 0.500 | 0
in l | Path length | cm | 1 | 0
in eps | Molar absorptivity | L/(mol·cm) | 10000 | 0
out c | Concentration | mol/L | a / (eps * l) | 6
out amm | Concentration | µmol/L | c * 1000000 | 3
out ap | Predicted absorbance | - | eps * c * l | 6

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →