Convert absorbance to concentration with the Beer–Lambert law: c = A / (εl), where A is absorbance, ε is the substance’s molar absorptivity, and l is the light path length. Enter those three values to calculate concentration in mol/L; the result assumes the law applies and the absorbance and constants use compatible units.
Formula
The Beer–Lambert law is A = εlc. Rearranged to find concentration:
c = A / (εl)
- A is absorbance, a dimensionless quantity. Absorbance is often written as AU, but AU is not a separate physical unit.
- ε is the molar absorptivity, also called the molar extinction coefficient, in L/(mol·cm). Its value depends on the absorbing substance and measurement conditions, especially wavelength and solvent.
- l is the optical path length through the sample, in cm.
- c is concentration in mol/L, or molarity.
With ε in L/(mol·cm) and l in cm, the units cancel to give mol/L. If ε is provided in different units, convert it or use a consistent version of the equation. The calculator does not look up ε: use a value appropriate to the specific analyte and wavelength.
Worked Example
Using the calculator’s default values—A = 0.500, ε = 10,000 L/(mol·cm), and l = 1 cm—calculate:
- Multiply absorptivity by path length: εl = (10,000 L/(mol·cm))(1 cm) = 10,000 L/mol.
- Divide absorbance by that product: c = 0.500 / (10,000 L/mol) = 0.000050000 mol/L.
- To the calculator’s eight decimal places, the result is 0.00005000 mol/L, equivalent to 50.000 μmol/L.
The concentration is an estimate from the supplied values. If ε is wrong for the wavelength or conditions, the calculated concentration will be wrong even if the arithmetic is correct.
Assumptions
- The sample follows the Beer–Lambert law over the measured range: absorbance is proportional to concentration and path length.
- Absorbance is measured at a wavelength for which the supplied molar absorptivity applies.
- The sample is sufficiently clear and homogeneous that scattering, bubbles, and other optical effects do not dominate.
- The absorbing species and measurement conditions are represented by the chosen ε value; no universal absorptivity is assumed.
How the Relationship Works
A spectrophotometer measures how much light passes through a sample relative to a reference. Transmittance is the transmitted-light fraction, T = I/I₀, where I₀ is incident intensity and I is transmitted intensity. Absorbance is defined as A = −log₁₀(T). A higher absorbance means a smaller fraction of the light reaches the detector.
For a dilute absorbing solution under suitable conditions, absorbance increases in proportion to both the number of absorbing molecules in the light path and the distance the light travels through the sample. Molar absorptivity captures how strongly the species absorbs at a particular wavelength. That proportional relationship gives A = εlc.
Absorbance itself is dimensionless, not a direct concentration reading. It becomes a concentration estimate only when ε and l are known or when a calibration curve supplies the relationship between absorbance and concentration.
Using a Calibration Curve
In routine measurements, a calibration curve is often more reliable than calculating from a tabulated ε. Measure several standards of known concentration under the same conditions as the unknown, then plot absorbance against concentration. In the linear range, a fitted line has the form A = mc + b, where m is the slope and b is the intercept. Rearrange it as c = (A − b)/m to estimate the unknown concentration.
The simple calculator uses the Beer–Lambert equation and assumes the calibration line passes through zero. A real calibration can have a nonzero intercept because of blank mismatch, background absorption, or instrument effects. If you have a measured calibration line, use its slope and intercept rather than treating them as zero or substituting an unrelated ε.
- Prepare standards that cover the expected unknown concentration, including a blank where appropriate.
- Measure standards and unknown at the same wavelength, with the same solvent, cuvette orientation, and path length.
- Check that the unknown’s absorbance lies within the validated calibration range; do not rely on extrapolation far beyond it.
- Repeat measurements when practical and report the calibration method and any dilution factor applied.
Choosing Values and Reading the Result
Choose ε for the exact absorbing species and wavelength used. Values reported in reference tables may depend on solvent, pH, temperature, or chemical form. An absorptivity value cannot be transferred blindly between wavelengths or between related compounds. If the reported coefficient uses units such as L/(mol·mm), convert the path length or coefficient so the units match; for example, 1 cm = 10 mm.
Path length is the distance light travels through the sample, not necessarily the outside width of the container. A standard cuvette commonly has a 1 cm optical path, but other cells and microvolume measurements may use different paths. Use the specified path length for your measurement rather than assuming it.
The output is molarity. To convert mol/L to millimolar, multiply by 1,000; to convert to micromolar, multiply by 1,000,000. If the sample was diluted before measurement, the calculator gives the concentration in the measured, diluted sample. Multiply by the total dilution factor to recover the original sample concentration. For example, a tenfold dilution requires multiplying the measured concentration by 10.
Common Problems and Limits
- Using the wrong ε: absorptivity varies with wavelength and conditions. A plausible-looking result is not proof that the selected value is appropriate.
- Mixing units: if ε is in L/(mol·cm), use l in cm. A path length entered in mm without conversion creates a tenfold error.
- Ignoring dilution: correct the measured concentration by the dilution factor when you need the original sample concentration.
- Measuring outside the linear range: high absorbance can produce unreliable readings because very little light reaches the detector; at very low absorbance, background and instrument noise can be important.
- Overlooking interference: other absorbing compounds, turbidity, particles, fingerprints, bubbles, or an unsuitable blank can affect the reading.
Beer–Lambert behavior is an approximation, not a guarantee at every concentration. Chemical interactions, changes in speciation, stray light, scattering, and instrumental limitations can make absorbance depart from a straight-line relationship. When accuracy matters, validate the range with standards and use a suitable blank and method. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.
Frequently Asked Questions
How do you calculate concentration from absorbance?
For a known molar absorptivity and path length, use c = A/(εl). Make sure ε and l use compatible units, then apply any dilution factor if the sample was diluted.
Can absorbance alone give concentration?
No. Absorbance must be related to concentration using a known ε and path length, or a calibration curve made from standards. The same absorbance can correspond to different concentrations for substances with different absorptivities.
What is the Beer–Lambert law?
It is A = εlc, which describes the proportional relationship between absorbance, molar absorptivity, optical path length, and concentration under suitable conditions.
What units should concentration have?
With ε in L/(mol·cm) and path length in cm, the calculated concentration is mol/L. It can be converted to mM or μM using factors of 1,000 or 1,000,000, respectively.
Why is my calculated concentration different from a standard curve result?
The ε value may not match the actual wavelength or sample conditions, or the calibration may have a nonzero intercept. Dilution, blanking, interference, and measurements outside the linear range can also explain differences.
Related
Formula used
in a | Absorbance | - | 0.500 | 0 in eps | Molar absorptivity | L/(mol·cm) | 10000 | 0.000001 in l | Path length | cm | 1 | 0.000001 out c | Concentration | mol/L | a / (eps * l) | 8
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Cell Culture Doubling Time Equation and Calculator24.00 h
- Cell Culture Seeding Density Calculator and Formula4,000.00 cells/cm^2
- Cell Culture Doubling Time Calculator and Formula24.00 h
- CFU From Dilution: Calculate Colony-Forming Units10,000,000 CFU/mL
- Cell Culture Doubling Time Calculator and Formula24.00 h
- Zero Order Release Kinetics Calculator and Explanation5.000 mg/h