molecalculator

Moles & Molar Mass

Air Density per Altitude: Standard Values and Calculator

Calculator No. 01-3053 · Updated · Formula and assumptions shown below

Air density 1.225 kg/m^3
Standard pressure
101.325 kPa
= 101.325 × (1 − 0.0065 × Geometric altitude ÷ 288.15) ^ 5.25587981271668
Standard temperature
288.15 K
= 288.15 − 0.0065 × Geometric altitude
Geometric altitude
0 m
Set in the form below
You enter
Geometric altitude (m)
You get
Air density (kg/m^3), Standard pressure (kPa), Standard temperature (K)
Rounding
3 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Air density decreases as altitude rises: in the International Standard Atmosphere, it is about 1.225 kg/m³ at sea level, 0.905 kg/m³ at 1,000 m, and 0.736 kg/m³ at 2,000 m. This calculator estimates density at a selected geometric altitude using the standard lower-atmosphere model; enter altitude in metres to get air density in kg/m³.

Formula

For the standard troposphere, density is calculated as:

ρ = ρ₀ × (1 − Lh/T₀)[(g₀M)/(R L) − 1]

  • ρ is air density in kilograms per cubic metre (kg/m³).
  • ρ₀ is sea-level standard density, 1.225 kg/m³.
  • h is geometric altitude in metres, measured above mean sea level for this approximation.
  • L is the standard temperature lapse rate, 0.0065 K/m.
  • T₀ is sea-level standard temperature, 288.15 K.
  • g₀ is standard gravitational acceleration, 9.80665 m/s².
  • M is the molar mass of dry air, approximately 0.0289644 kg/mol.
  • R is the molar gas constant, 8.31446261815324 J/(mol·K).

For the calculator’s density expression, the exponent is approximately 4.25588. Its companion pressure output uses p = p₀ × (1 − Lh/T₀)5.25588, with standard sea-level pressure p₀ = 101.325 kPa. Temperature follows T = T₀ − Lh. These expressions use the standard-atmosphere constants and are not measurements of local weather.

Worked Example

Using the defaults, altitude h = 0 m:

  1. Temperature factor: 1 − (0.0065 K/m × 0 m) / 288.15 K = 1.
  2. Density: 1.225 kg/m³ × 14.25587981271668 = 1.225 kg/m³.
  3. Standard pressure: 101.325 kPa × 15.25587981271668 = 101.325 kPa.
  4. Standard temperature: 288.15 K − (0.0065 K/m × 0 m) = 288.15 K.

Assumptions

  • The atmosphere follows the International Standard Atmosphere’s tropospheric temperature profile, with a 6.5 K/km decrease in temperature.
  • Air is treated as dry, with standard composition and the ideal-gas relationship implicit in the standard-atmosphere model.
  • Altitude is geometric altitude from sea level; the model is limited here to 0–11,000 m.
  • Humidity, weather, local pressure deviations, and terrain elevation effects are not included.

Standard air density by altitude

The table gives rounded reference values for the same standard atmosphere. Density is mass per unit volume, so a cubic metre of air contains less mass at higher altitude. Values are approximate and rounded to three decimal places; the calculator uses its formula rather than looking up these rows.

Altitude Approx. density Approx. standard pressure Standard temperature
0 m 1.225 kg/m³ 101.325 kPa 15 °C
1,000 m 0.905 kg/m³ 89.875 kPa 8.5 °C
2,000 m 0.736 kg/m³ 79.495 kPa 2 °C
5,000 m 0.736 kg/m³ 54.020 kPa −17.5 °C
10,000 m 0.414 kg/m³ 26.436 kPa −50 °C

Why density changes with altitude

Gravity keeps the atmosphere concentrated near Earth’s surface. The weight of the air above compresses lower layers, so pressure and density are greatest near sea level and decline with height. Temperature also affects density: for a given pressure, warmer air is less dense than cooler air. In the standard troposphere, both pressure and temperature decrease with altitude, and their combined effect produces the density curve in the formula.

At a fixed temperature and pressure, the ideal-gas relation can be written as ρ = pM/(RT). That form is useful when actual pressure and temperature are known. The altitude calculator instead estimates standard pressure and temperature from altitude, then returns a consistent standard-atmosphere density. It cannot infer today’s local conditions from elevation alone.

What the estimate is useful for

Air density matters wherever the mass of air or its resistance to motion matters. It influences aerodynamic lift and drag, aircraft performance, engine air intake, ventilation estimates, and the buoyancy of balloons. For instance, the standard value at 2,000 m is roughly 60% of sea-level density, so an object moving at the same speed through that air generally encounters less aerodynamic force, all else being equal. The exact result depends on the object and operating conditions.

For a quick standard reference, the calculator is appropriate. For a calculation that depends on real conditions, obtain local or forecast pressure and temperature, and account for humidity if the required accuracy warrants it. Weather pressure reports may also be corrected to sea level; use station pressure at the actual site when applying the ideal-gas equation locally.

Limits, units, and common mistakes

  • Do not treat altitude as the only real-world variable. A high-pressure, cold day can have a different density from a warm, low-pressure day at the same elevation.
  • Check the altitude reference. The model assumes metres above sea level. Height above a local ground point is not the same quantity unless the ground elevation is added.
  • Keep units consistent. The calculator accepts metres and reports kg/m³. To convert kg/m³ to g/L, the numerical value is unchanged; to convert to kg/L, divide by 1,000.
  • Respect the model’s range. This calculator is set for 0–11,000 m, the tropospheric layer represented by the stated lapse rate. Above that, atmospheric layers have different temperature rules; extending this equation would be misleading.

A related misconception is that air density falls at one fixed percentage per kilometre. It does not: the decrease is nonlinear because pressure and temperature both change, and the local rate of change varies with altitude. Rounded table values are suitable for orientation, not for precision engineering or flight planning.

Frequently Asked Questions

What is the density of air at sea level?
Under standard conditions, dry air has a density of about 1.225 kg/m³ at sea level, with pressure 101.325 kPa and temperature 15 °C. Actual density varies with weather, temperature, and humidity.

What is air density at 1,000 metres?
The standard-atmosphere estimate is approximately 0.905 kg/m³ at 1,000 m. It is lower than the sea-level value because pressure has fallen with altitude.

How much does air density decrease with altitude?
There is no single fixed percentage decrease per kilometre. In the standard atmosphere, density falls nonlinearly; it is about 1.225 kg/m³ at sea level and 0.414 kg/m³ at 10,000 m.

Does cold weather make air denser?
At the same pressure, colder air is denser than warmer air. In practice, pressure also changes, so both temperature and pressure are needed to estimate actual density accurately.

Is air density the same as air pressure?
No. Pressure describes force per area from the air, while density describes air mass per volume. They are related through temperature and the gas properties, but they are different quantities.

Related

Formula used
in h | Geometric altitude | m | 0 | 0 | 11000
out rho | Air density | kg/m^3 | 1.225 * (1 - 0.0065 * h / 288.15) ^ 4.25587981271668 | 3
out p | Standard pressure | kPa | 101.325 * (1 - 0.0065 * h / 288.15) ^ 5.25587981271668 | 3
out t | Standard temperature | K | 288.15 - 0.0065 * h | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →