molecalculator

Moles & Molar Mass

Air Density Table: Values by Temperature and Pressure

Calculator No. 01-3669 · Updated · Formula and assumptions shown below

Air density 1.204 kg/m³
Air density
1.204 g/L
= Air density
Air temperature
20 °C
Set in the form below
Absolute pressure
101.325 kPa
Set in the form below
You enter
Air temperature (°C), Absolute pressure (kPa)
You get
Air density (kg/m³), Air density (g/L)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

An air density table gives the mass of air per unit volume at specified temperatures and pressures. The calculator below estimates dry-air density from air temperature and pressure; enter those two values to get density in kg/m³ and g/L.

Formula

For dry air treated as an ideal gas, density is pressure divided by the specific gas constant for dry air times absolute temperature:

ρ = p / (Rd T)

  • ρ is air density in kilograms per cubic metre (kg/m³).
  • p is absolute pressure in pascals (Pa). The calculator accepts kilopascals and converts using 1 kPa = 1,000 Pa.
  • Rd is the specific gas constant for dry air, 287.05 J/(kg·K), a conventional value.
  • T is absolute temperature in kelvins (K), calculated as temperature in °C + 273.15.

Because 1 J = 1 Pa·m³, the units reduce to kg/m³. The second output uses the equality 1 kg/m³ = 1 g/L. The equation can also be written directly for the inputs shown: ρ = (p in kPa × 1,000) / [287.05 × (temperature in °C + 273.15)].

Worked Example

Using the calculator defaults, the air temperature is 20 °C and absolute pressure is 101.325 kPa.

  1. Convert temperature to kelvins: T = 20 + 273.15 = 293.15 K.
  2. Convert pressure to pascals: p = 101.325 × 1,000 = 101,325 Pa.
  3. Substitute: ρ = 101,325 / (287.05 × 293.15) = 1.204 kg/m³, rounded to three decimal places.
  4. Convert to grams per litre: 1.204 kg/m³ = 1.204 g/L.

The result is an estimate for dry air at those conditions. A table may show slightly different values because of rounding, the constants used, humidity, or a more detailed gas model.

Assumptions

  • Air is dry and behaves as an ideal gas.
  • The specific gas constant is 287.05 J/(kg·K).
  • Pressure entered is absolute pressure, not gauge pressure.
  • Temperature is converted from Celsius to kelvins using +273.15.

Air Density Table

The following reference values use the same dry-air ideal-gas equation and standard pressure of 101.325 kPa. Values are rounded to three decimal places; density generally decreases as temperature rises.

Temperature Air density at 101.325 kPa
−20 °C 1.395 kg/m³
−10 °C 1.342 kg/m³
0 °C 1.292 kg/m³
10 °C 1.247 kg/m³
20 °C 1.204 kg/m³
25 °C 1.184 kg/m³
30 °C 1.164 kg/m³
40 °C 1.127 kg/m³
50 °C 1.093 kg/m³

These are not universal values for each temperature: the listed pressure is part of the condition. For example, at 20 °C and 80.000 kPa, the same model gives 0.951 kg/m³. At fixed temperature, density changes in direct proportion to absolute pressure. The table is useful for a quick comparison, while the calculator covers other pressure and temperature pairs.

How Air Density Changes

Air density is the mass of air in a given volume. Under the ideal-gas approximation, higher pressure packs more gas molecules into a volume, increasing density. Higher temperature means molecules have greater average kinetic energy; at a fixed pressure, the gas expands and density falls. This explains why warm air at sea-level pressure is less dense than cold air at the same pressure.

Altitude commonly affects density because atmospheric pressure falls as elevation increases. Temperature also varies with weather and height, so an elevation alone does not determine an exact density. For flight, weather calculations, or engineering work, use pressure and temperature measured or specified for the relevant location and time. Do not substitute elevation for pressure without an appropriate atmospheric model.

Humidity, Units, and Common Errors

The table and calculator represent dry air. Humid air at the same temperature and total pressure is usually less dense than dry air: water molecules have lower molar mass than the average molecules in dry air, so replacing some dry-air molecules with water vapour reduces the mixture’s density. For precise work, use a moist-air equation that accounts for water-vapour pressure rather than treating humidity as a simple correction.

  • Use absolute pressure. A gauge pressure is measured relative to local atmospheric pressure. Add local atmospheric pressure to gauge pressure before using the equation. A negative gauge reading is not a negative absolute pressure.
  • Convert temperature correctly. The gas equation uses kelvins, not Celsius. Adding 273.15 is essential; using 20 directly would produce a substantially wrong result.
  • Keep units consistent. This calculator accepts kPa and °C. Its formula explicitly converts kPa to Pa and Celsius to kelvins.
  • Understand the scope. Dry-air ideal-gas values work well for many ordinary conditions, but unusual pressures, high precision requirements, and humid-air applications may call for a more complete model.

A related misconception is that standard air has one fixed density. A commonly quoted value near 1.225 kg/m³ refers to a particular standard atmosphere condition, approximately 15 °C and 101.325 kPa, not every location or day. Density changes whenever temperature, pressure, or composition changes.

When to Use a Table or Calculator

Use a table when a quick reference at a stated standard pressure is enough. Use the calculator when pressure differs from the table, such as at altitude or under a specified operating condition. For an accurate result, record the units, whether pressure is absolute, the temperature, and whether humidity matters. Report the assumptions along with the answer; “air density is 1.20 kg/m³” is less informative than giving the conditions that produced it.

The outputs in kg/m³ and g/L are numerically identical, which can make the second unit convenient for comparing a litre of air with other materials. This does not mean a litre of air always weighs the same amount: its mass follows the conditions. At 20 °C and standard pressure, one cubic metre of dry air has a mass of about 1.204 kg according to the calculator’s model.

Frequently Asked Questions

What is the density of air at room temperature?
At 20 °C and 101.325 kPa, dry air has an estimated density of 1.204 kg/m³ using the ideal-gas equation and the stated constant. Different pressure or humidity gives a different value.

What is the standard density of air?
There is no single standard value unless the reference conditions are specified. A commonly used value is about 1.225 kg/m³ at 15 °C and 101.325 kPa for dry air.

Does air density increase with altitude?
No. Atmospheric pressure generally decreases with altitude, so air density usually decreases as well. Actual density also depends on temperature and moisture.

Is humid air denser than dry air?
At the same temperature and total pressure, humid air is usually less dense. Water vapour has a lower molar mass than the main components of dry air.

How do I convert air density from kg/m³ to g/L?
The numerical value is unchanged: 1 kg/m³ equals 1 g/L. For example, 1.204 kg/m³ is 1.204 g/L.

Can I use gauge pressure in the formula?
Not directly. The equation requires absolute pressure. Convert gauge pressure by adding the local atmospheric pressure, using consistent units.

Related

Formula used
in t | Air temperature | °C | 20 | -273.15
in p | Absolute pressure | kPa | 101.325 | 0
out d | Air density | kg/m³ | (p * 1000) / (287.05 * (t + 273.15)) | 3
out gl | Air density | g/L | d | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →