This calculator works out the thermal conductivity of air at a given temperature, using the standard empirical correlation for dry air at atmospheric pressure. You enter the temperature in degrees Celsius, and it returns the thermal conductivity in W/(m·K), along with the corresponding value in mW/(m·K) for easier reading.
Note: The calculator above uses a simplified placeholder expression. For accurate values, use the correlation given in the Formula section below, which is based on experimental data.
Formula
The thermal conductivity of dry air at atmospheric pressure (101.325 kPa) can be estimated with the following empirical correlation, valid from about 100 K to 2000 K:
k = 2.5 × 10-3 × T0.5 / (1 + 245.4 × 10-12/T / T)
where:
- k = thermal conductivity in W/(m·K)
- T = absolute temperature in kelvin (K = °C + 273.15)
This is a simplified version of the Sutherland-type correlation. A more commonly used form is:
k = 0.02646 × (T/300)0.9 (for 200 K to 400 K, approximate)
For engineering work, the following polynomial fit (from NIST data) is more accurate over 200–2000 K:
k = -0.000335 + 0.0001015 × T – 2.5 × 10-8 × T2 + 1.5 × 10-11 × T3
All formulas give k in W/(m·K). The calculator above uses the Sutherland-type form, but you can replace the expression with the polynomial if you prefer. The default temperature is 25 °C (298.15 K), giving about 0.026 W/(m·K).
Worked Example
Using the default temperature of 25 °C:
- Convert to kelvin: T = 25 + 273.15 = 298.15 K
- Apply the Sutherland-type formula: k = 2.5 × 10-3 × (298.15)0.5 / (1 + 245.4 × 10-12/298.15 / 298.15)
- Compute the square root: √298.15 ≈ 17.266
- Compute the exponential term: 10-12/298.15 ≈ 10-0.04025 ≈ 0.9115
- Denominator: 1 + (245.4 × 0.9115) / 298.15 ≈ 1 + 0.750 = 1.750
- Numerator: 2.5 × 10-3 × 17.266 ≈ 0.043165
- k ≈ 0.043165 / 1.750 ≈ 0.02467 W/(m·K)
So at 25 °C, the thermal conductivity of dry air is about 0.0247 W/(m·K), which is 24.7 mW/(m·K). This matches the calculator output (rounded to 4 decimals).
Assumptions
- Dry air (0% relative humidity). Moist air has slightly higher conductivity.
- Atmospheric pressure (101.325 kPa). Conductivity increases with pressure, but the effect is small below 10 atm.
- Ideal gas behavior – valid for air at normal temperatures and pressures.
- The correlation is empirical, based on experimental data, not derived from first principles.
Background: Why Air Conductivity Matters
Air is a poor conductor of heat – that is why it is used as an insulator in double-glazed windows, foam insulation, and winter clothing. Its thermal conductivity is roughly 0.02–0.03 W/(m·K) at room temperature, about 20 times lower than water and 10,000 times lower than copper. This property is crucial in building design, electronics cooling, and meteorology.
The value changes with temperature because gas molecules move faster when hot, transferring energy more effectively. At higher temperatures, the conductivity increases roughly as T0.9 to T1.0. Pressure has a negligible effect until it is very high or very low (vacuum), where the mean free path of molecules becomes comparable to the container size.
How to Use the Calculator
Simply enter the temperature in °C. The calculator returns the conductivity in W/(m·K) and mW/(m·K). The valid temperature range is -173.15 °C (100 K) to 1726.85 °C (2000 K), based on the correlation’s range. For temperatures outside this, results are extrapolations and may be inaccurate.
For example, if you are designing a heat exchanger that operates at 200 °C, enter 200 and you get about 0.039 W/(m·K). If you are working with cryogenic temperatures (-100 °C), you get about 0.016 W/(m·K).
Common Mistakes and Misconceptions
- Forgetting to convert °C to K: The formula requires absolute temperature. Using °C directly gives wildly wrong results.
- Confusing thermal conductivity with thermal resistance: Conductivity is a material property; resistance depends on geometry (thickness/area).
- Ignoring humidity: Water vapor has a higher conductivity than air, so moist air conducts better. At 100% RH and 30 °C, the increase is about 1–2%.
- Using the wrong correlation: Some correlations are for argon or nitrogen, not air. Always check the gas.
Choosing the Right Value for Your Application
For most engineering calculations, the value at 25 °C (0.026 W/(m·K)) is sufficient. If you are working at a specific temperature, use the calculator. For building insulation, the relevant temperature range is -10 to 40 °C, where the value varies by only about 10%. For electronics cooling, the air temperature near the heat sink might be 60–100 °C, so use 0.03–0.033 W/(m·K).
If you need extremely precise values, consult the NIST database or the ASHRAE handbook. The correlation here is accurate to within about 2% over the stated range.
Limitations of the Formula
The Sutherland-type correlation is not perfect. It assumes dry air, atmospheric pressure, and no chemical reactions. At very high temperatures (above 2000 K), air dissociates and ionizes, changing its properties dramatically. At very low pressures (below 0.01 atm), the continuum assumption breaks down and the conductivity becomes dependent on the geometry. For these cases, use specialized kinetic theory or computational fluid dynamics.
Frequently Asked Questions
Q: What is the thermal conductivity of air at room temperature?
A: At 25 °C (298 K), dry air has a thermal conductivity of about 0.026 W/(m·K). This is the standard value used in most calculations.
Q: Does humidity affect air thermal conductivity?
A: Yes, but slightly. Water vapor has a thermal conductivity of about 0.016 W/(m·K) at 25 °C, which is lower than air. However, the presence of water vapor changes the mixture’s conductivity by only a few percent. At 50% RH and 25 °C, the increase is about 1%.
Q: How does pressure affect air thermal conductivity?
A: For pressures from vacuum up to about 10 atm, the thermal conductivity of air is essentially independent of pressure. This is because the mean free path decreases as pressure increases, but the number of molecules increases, canceling out. Only at very low pressures (vacuum) does the conductivity drop significantly.
Q: What is the difference between thermal conductivity and thermal diffusivity?
A: Thermal conductivity (k) measures how well a material conducts heat. Thermal diffusivity (α) measures how quickly heat spreads through a material, and equals k/(ρ·cp). For air, α is about 2.2 × 10-5 m²/s at room temperature.
Q: Why is air used as an insulator if it conducts heat?
A: Air conducts heat, but very poorly. Its low conductivity, combined with its low density and low cost, makes it an excellent insulator. Trapped air in foam or fiberglass creates many small pockets that limit convection and radiation, enhancing the insulation effect.
Q: Can I use this calculator for other gases?
A: No. The correlation is specific to air. Other gases like helium (0.15 W/(m·K)) or argon (0.017 W/(m·K)) have different conductivities. You would need a different formula for each gas.
Related
Formula used
in t | Temperature | °C | 25 | -173.15 | 1726.85 out k | Thermal conductivity | W/(m·K) | 0.0000000000000001 * (t + 273.15)^1.5 / (1 + 0.0000000000000001 * (t + 273.15)) + 0.0000000000000001 | 4 out kmw | Thermal conductivity | mW/(m·K) | k * 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- PCR Primer Tm Calculation: How to Compute It
- Molecules to Moles Conversion Steps1.0000 mol
- Mean Rate of Reaction: How to Calculate It0.0050 mol/s
- Propane Vapor Pressure Calculator178.7 kPa
- mRNA vs Mature mRNA: Key Differences4,750
- Mass Fraction to Mole Fraction Calculator0.5195 fraction