In the AQA A-level chemistry practical, you measure the temperature change when a known mass of substance reacts with or dissolves in water, then calculate the enthalpy change using q = mcΔT. You enter the mass of substance, the mass of solution, the temperature change, and the molar mass to get the enthalpy change in kJ mol⁻¹.
Formula
The heat energy change is q = msol × c × ΔT, where msol is the mass of the solution (usually water) in grams, c is the specific heat capacity of the solution (4.18 J g⁻¹ °C⁻¹ for dilute aqueous solutions), and ΔT is the temperature change in °C. The enthalpy change per mole is then ΔH = −q / n, where n is the number of moles of the limiting reactant (mass of substance divided by its molar mass). The negative sign is added because the calculation gives the heat absorbed by the solution; the reaction releases that heat, so the enthalpy change is negative for exothermic reactions.
Worked Example
Suppose you add 0.500 g of anhydrous calcium chloride (molar mass 111.0 g/mol) to 50.0 g of water, and the temperature rises by 10.5 °C.
- Calculate the heat absorbed by the solution: q = 50.0 g × 4.18 J g⁻¹ °C⁻¹ × 10.5 °C = 2194.5 J ≈ 2.19 kJ.
- Calculate the moles of CaCl₂: n = 0.500 g ÷ 111.0 g/mol = 0.00450 mol.
- Calculate the enthalpy change: ΔH = −2.19 kJ ÷ 0.00450 mol = −487 kJ/mol (exothermic).
The calculator uses the same steps: it first computes q in joules, then divides by the number of moles (mass in grams × 1000 / molar mass) to give kJ/mol.
Assumptions
- The specific heat capacity of the solution is equal to that of water (4.18 J g⁻¹ °C⁻¹). This is valid for dilute solutions.
- The density of the solution is 1.00 g/mL, so the mass of solution equals its volume in mL.
- No heat is lost to the surroundings (the calorimeter is perfectly insulated).
- The reaction goes to completion and the limiting reactant is fully consumed.
- The temperature change is the maximum observed, corrected for cooling if necessary.
How the AQA Practical Works
In the required practical, you typically measure the enthalpy change of a reaction such as neutralisation (acid + base), dissolution of a salt, or combustion of an alcohol. For neutralisation, you mix known volumes of acid and alkali in a polystyrene cup (a simple calorimeter) and record the temperature rise. For dissolution, you add a known mass of solid to water and measure the temperature change. For combustion, you burn a known mass of alcohol under a calorimeter containing water and measure the temperature rise of the water.
The key measurements are: the mass (or volume, assuming density = 1 g/mL) of the solution, the temperature change, and the mass of the substance that provides the moles of the limiting reactant. The temperature is taken at regular intervals before and after mixing to plot a temperature-time graph, which allows you to extrapolate the maximum temperature and correct for heat loss.
Common Sources of Error
The biggest error in school calorimetry is heat loss to the surroundings. Even with a polystyrene cup, heat escapes through the sides, top, and any thermometer or stirrer. This causes the measured temperature change to be smaller than the true value, so the calculated enthalpy change is less exothermic (or less endothermic) than the accepted value. Other errors include:
- Incomplete reaction (e.g., not all solid dissolves).
- Reaction not going to completion (e.g., weak acid not fully neutralised).
- Heat absorbed by the calorimeter and thermometer (not accounted for).
- Evaporation of solution, especially in combustion experiments.
- Inaccurate measurement of temperature (e.g., reading before equilibrium).
- Assuming the density and specific heat of the solution are exactly those of water.
To reduce errors, you use a lid on the cup, insulate it, stir gently, and take readings at regular intervals to plot a cooling curve. For combustion, you also need to correct for the heat absorbed by the copper calorimeter and account for incomplete combustion.
Comparing Methods: Solution vs Combustion
Solution calorimetry (dissolution or neutralisation) is relatively accurate because the reaction happens in the liquid where heat transfer is efficient. However, the enthalpy of dissolution includes both lattice energy and hydration energy, so it can be endothermic or exothermic. Combustion calorimetry is less accurate because much heat is lost to the air and the calorimeter, and combustion is often incomplete (soot forms). The AQA practical for combustion uses a spirit burner and a metal can; the calculated enthalpy of combustion is often 30–50% lower than the data-book value because of these losses.
For neutralisation, the enthalpy change of reaction for a strong acid and strong base is close to −57 kJ/mol, but with weak acids it is less exothermic because energy is used to ionise the acid.
How to Choose the Limiting Reactant
To calculate ΔH per mole, you must know which reactant is in excess. Usually you use a known volume of one solution (e.g., 25.0 mL of 1.0 mol/L HCl) and add an excess of the other (e.g., 30.0 mL of 1.0 mol/L NaOH). The moles of the limiting reactant are then the moles of HCl (0.025 mol). In dissolution, the solid is the limiting reactant because it is completely consumed (if it all dissolves). In combustion, the alcohol is the limiting reactant because it is burned completely (if you use a known mass).
If you use the wrong reactant as the limiting one, your ΔH will be wrong by a factor equal to the ratio of moles. Always check that the reactant you choose is the one that is completely used up.
Safety and Practical Tips
Always wear safety goggles and follow your lab method, the safety data sheet (SDS) and your supervisor. When handling acids and bases, avoid skin contact. For combustion, keep flammable liquids away from open flames and use a draught shield. When measuring temperature, use a thermometer with 0.1 °C divisions and read it at eye level. Stir continuously but gently to ensure even temperature. Plot temperature against time for at least 2 minutes before and after mixing to get a reliable extrapolated temperature change.
For the calculation, use the total mass of the solution (not just the water). If you mix 25 mL of acid with 30 mL of base, the total mass is 55 g (assuming density 1 g/mL). Also, if the solid itself is added, include its mass in the solution mass if it dissolves completely (but for simplicity, many methods use only the water mass; the difference is small). The specific heat capacity of the solution is taken as 4.18 J g⁻¹ °C⁻¹, but for concentrated solutions it can be slightly different; this is a source of systematic error.
Frequently Asked Questions
Why is my enthalpy of combustion always lower than the data book value?
Heat loss to the surroundings and incomplete combustion are the main reasons. The alcohol may not burn completely (forming soot), and much of the heat escapes into the air instead of heating the water. The measured temperature rise is therefore too small, giving a ΔH that is less exothermic than the true value.
Do I need to include the calorimeter’s heat capacity?
In AQA, you are not required to include the heat capacity of the polystyrene cup or thermometer because they are small and the method assumes they are negligible. However, if you want a more accurate result, you could measure the calorimeter constant and add it to the mcΔT term. For the exam, stick to the simple method.
What is the temperature-time graph for?
It allows you to correct for heat loss. You plot temperature against time, draw the best-fit lines for the initial and final periods, and extrapolate them back to the time of mixing. The temperature difference at that point is the corrected ΔT, which is larger than the maximum observed temperature.
Can I use this calculator for any enthalpy practical?
Yes, as long as you know the mass of the solution, the temperature change, and the moles of the limiting reactant. For neutralisation, you can calculate moles from concentration and volume; for dissolution, from mass and molar mass; for combustion, from mass of fuel burned and molar mass. Just enter the appropriate values.
Why is the sign of ΔH sometimes positive?
If the temperature decreases (endothermic reaction), ΔT is negative, so q is negative, and the enthalpy change is positive. For example, dissolving ammonium nitrate in water is endothermic, so the solution cools. The calculator automatically gives the sign based on your ΔT entry.
Related
Formula used
in m | Mass of substance | g | 0.500 | 0 in mm | Molar mass of substance | g/mol | 40.08 | 0.001 in msol | Mass of solution | g | 50.0 | 0 in dT | Temperature change | °C | 10.5 | -273.15 in c | Specific heat capacity of solution | J/g·°C | 4.18 | 0 out q | Heat energy change | J | m * 1000 / mm * c * msol * dT | 0 out dH | Enthalpy change | kJ/mol | q / 1000 / (m / mm) | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality to g/L Converter & Formula29.220 g/L
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check