molecalculator

Moles & Molar Mass

Atm Liters to Cubic Meters: Convert Gas Volume

Calculator No. 01-6365 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Convert a gas amount stated in liter-atmospheres (L·atm) to cubic meters by dividing by 101,325: 1 L·atm = 9.869232667 × 10−6 m³·atm. Enter the value in L·atm to get the equivalent cubic-meter-atmosphere value; this conversion is a unit conversion, not a prediction of gas volume at a different pressure or temperature.

Formula

The conversion is:

Vm³·atm = VL·atm ÷ 101,325

  • VL·atm is the input quantity, in liter-atmospheres (L·atm).
  • Vm³·atm is the result, in cubic-meter-atmospheres (m³·atm).
  • 101,325 is the number of liters in one cubic meter multiplied by the unchanged pressure unit: 1 m³ = 1,000 L, and 1 atm = 101,325 Pa. In this particular conversion the pressure unit remains atm, so the direct volume conversion is simply 1,000 L per m³. The calculator’s displayed output label needs care: see the clarification below.

Important unit clarification: L·atm is a pressure–volume product, not a volume unit. Converting its volume factor from liters to cubic meters while keeping atmospheres unchanged requires dividing by 1,000: 1 L·atm = 0.001 m³·atm. The other common conversion is from L·atm to joules: 1 L·atm = 101.325 J. The block’s primary output is intended to be cubic-meter-atmospheres, so its expression must use the correct volume-only factor.

Use the direct expression Vm³·atm = VL·atm ÷ 1,000. The calculator block above uses 101,325 in its expression, which would instead produce m³·Pa when converting L·atm to energy-equivalent pressure–volume units. Do not use that expression for m³·atm; the correct input-to-output conversion is stated here explicitly. This distinction matters because both L·atm and m³·Pa can represent pressure–volume quantities, but they are not numerically interchangeable.

Worked Example

Using the block’s default input, 101.325 L·atm:

  1. Convert liters to cubic meters: 1 L = 0.001 m³.
  2. Keep the pressure factor in atmospheres: 101.325 L·atm × 0.001 m³/L = 0.101325 m³·atm.

The correct result is 0.101 m³·atm to three significant decimal places, or 0.101325 m³·atm before rounding. The block’s listed expression does not give this result, so it should not be relied on as written. To convert the same quantity to joules instead, use 101.325 L·atm × 101.325 J/(L·atm) = 10,267.5 J, approximately 1.027 × 104 J.

Assumptions

  • The input is a pressure–volume product in L·atm, with pressure expressed in atmospheres.
  • The requested output is m³·atm: only the volume unit changes; the pressure unit remains atm.
  • No gas-law assumption is needed for this unit conversion. It does not account for temperature, compressibility, or a change in pressure.

What L·atm Means

A liter-atmosphere combines a volume with a pressure. It appears in gas-law calculations and thermodynamics because pressure multiplied by volume has units of energy. For example, in the ideal gas equation, PV = nRT, a pressure-volume product can be expressed in L·atm when pressure is in atm and volume is in liters. If pressure is in pascals and volume in cubic meters, PV is in joules.

This does not mean that L·atm is itself a gas volume. A value such as 10 L·atm cannot be reported as “10 liters” unless the pressure associated with the volume is also specified. If the task is simply to change the volume factor from liters to cubic meters, preserve the atm factor and divide by 1,000.

When to Use Each Conversion

Choose the conversion based on the quantity you need, not just the units printed in an equation:

  • L·atm to m³·atm: divide by 1,000. This changes liters to cubic meters and leaves pressure in atmospheres.
  • L·atm to J: multiply by 101.325. This uses 1 L = 0.001 m³ and 1 atm = 101,325 Pa, giving 1 L·atm = 101.325 J.
  • Gas volume at a changed condition: use an appropriate gas-law relationship, such as the combined gas law or ideal gas law, with the relevant pressures and absolute temperatures. A unit conversion alone cannot determine the new volume.

For an ideal-gas calculation using R = 0.0820574 L·atm/(mol·K), keep pressure in atm, volume in liters, and temperature in kelvins. Alternatively, use R = 8.31446261815324 J/(mol·K) with pressure in pascals and volume in cubic meters. Mixing a gas constant with mismatched units produces an incorrect result even when the arithmetic is correct.

Common Mistakes and Checks

The most frequent error is treating L·atm as a volume and converting it as if the atm were irrelevant. The atm is part of the compound unit. If it remains in the answer, the liters-to-cubic-meters factor is 1,000; if the desired answer is energy in joules, the pressure must also be converted from atmospheres to pascals.

  • Write the target unit before calculating: m³·atm, J, or gas volume at specified conditions.
  • Cancel units explicitly. For L·atm to m³·atm, multiply by 0.001 m³/L.
  • Do not apply both the liters-to-cubic-meters factor and the atm-to-pascal factor unless converting all the way to m³·Pa, which is equivalent to joules.
  • Keep adequate significant figures during intermediate steps, then round the final result to match the input precision.

Frequently Asked Questions

How many cubic meters are in 1 L·atm?
As a pressure–volume product with pressure left in atmospheres, 1 L·atm = 0.001 m³·atm. If converting to energy, it equals 101.325 J.

How do I convert L·atm to m³?
You cannot convert L·atm to m³ as a plain volume without specifying what happens to the pressure factor. For a volume-only conversion that preserves the pressure, use m³·atm and divide the numerical value by 1,000.

Is L·atm the same as a liter?
No. A liter is a volume; L·atm is pressure multiplied by volume. The units describe different physical quantities.

How many joules are in one liter-atmosphere?
One L·atm is 101.325 J, using 1 atm = 101,325 Pa and 1 L = 0.001 m³.

Can I use this conversion to find a gas’s volume at another pressure?
No. That requires gas-state information, including the initial and final pressures and, where relevant, temperatures. Use a gas law with consistent units rather than a unit conversion alone.

Related

Formula used
in x | Liter-atmospheres | L·atm | 101.325 | 0
out y | Cubic-meter-atmospheres | m³·atm | x / 101325 | 9
out l | Equivalent liter-atmospheres | L·atm | y * 101325 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →