molecalculator

Moles & Molar Mass

Atomic Mass of Copper Sulfate (CuSO4)

Calculator No. 01-7382 · Updated · Formula and assumptions shown below

Molarity 0.0468 mol/L
Concentration in millimolar
46.81 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
249.69 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The atomic mass of copper sulfate (CuSO4, anhydrous) is 159.61 g/mol when using standard IUPAC atomic weights (Cu 63.546, S 32.06, O 15.999). For the common pentahydrate form (CuSO4·5H2O), the molar mass is 249.69 g/mol. This page explains how these values are calculated, why they matter, and how to use them in lab calculations.

Formula

The molar mass (M) of a compound is the sum of the atomic masses of its constituent atoms, each multiplied by its subscript in the chemical formula. For copper sulfate pentahydrate:

M(CuSO4·5H2O) = M(Cu) + M(S) + 4×M(O) + 5×[2×M(H) + M(O)]

Using IUPAC standard atomic weights:

  • Cu: 63.546 g/mol
  • S: 32.06 g/mol
  • O: 15.999 g/mol
  • H: 1.008 g/mol

Calculation: 63.546 + 32.06 + 4×15.999 + 5×(2×1.008 + 15.999) = 63.546 + 32.06 + 63.996 + 5×18.015 = 249.69 g/mol.

The calculator above uses this molar mass to convert a mass of copper sulfate pentahydrate into molarity (mol/L) when you specify the final solution volume. The formula is:

Molarity (mol/L) = mass (g) / molar mass (g/mol) / volume (L)

where volume in mL is converted to L by dividing by 1000.

Worked Example

Using the default values from the calculator: you weigh out 2.922 g of CuSO4·5H2O and dissolve it to a final volume of 250 mL.

  1. Convert volume to liters: 250 mL = 250 / 1000 = 0.250 L
  2. Calculate moles of solute: 2.922 g / 249.69 g/mol = 0.01170 mol (rounded to 4 significant figures)
  3. Calculate molarity: 0.01170 mol / 0.250 L = 0.04680 mol/L, which rounds to 0.0468 mol/L (4 decimal places as shown).
  4. Convert to millimolar: 0.04680 mol/L × 1000 = 46.80 mM.

The calculator gives the same result: 0.0468 mol/L and 46.80 mM.

Assumptions

  • The compound is pure and fully dissolved; no hydration or decomposition occurs.
  • The molar mass is based on the pentahydrate form (CuSO4·5H2O). If you use anhydrous CuSO4, the molar mass is 159.61 g/mol, and the result would differ.
  • The final solution volume is used (not the solvent volume). This is the standard for molarity.
  • Temperature and pressure do not affect molarity (they affect volume slightly, but for typical lab work this is negligible).

Why the Hydrate Form Matters

Copper sulfate is commonly sold as the blue pentahydrate, CuSO4·5H2O, which contains water molecules trapped in the crystal lattice. The anhydrous form (white or gray powder) is less common and is often used as a desiccant. When you weigh out copper sulfate for a solution, you must know which form you have. If you mistakenly use the pentahydrate mass but treat it as anhydrous, your molarity will be about 36% lower than intended. Always check the label: the pentahydrate is usually labeled “CuSO4·5H2O” or “copper(II) sulfate pentahydrate.”

How to Use the Calculator

This calculator is for preparing solutions of known concentration from a solid sample. Enter the mass of copper sulfate you have (in grams), the molar mass (default is for the pentahydrate; change it to 159.61 for anhydrous), and the final volume of solution you want (in mL). The calculator returns the molarity in mol/L and in mM. This is useful for making buffers, nutrient solutions, or any lab solution where you need a specific concentration.

For example, to make 500 mL of a 0.1 M CuSO4 solution using the pentahydrate, you would need:

mass = M × M × V = 0.1 mol/L × 249.69 g/mol × 0.500 L = 12.4845 g.

You can verify this by entering 12.4845 g, 249.69 g/mol, and 500 mL into the calculator; it will show 0.1 mol/L.

Common Mistakes and Misconceptions

  • Confusing hydrate and anhydrous: Using the wrong molar mass is the most common error. Always verify the chemical formula.
  • Using solvent volume instead of final volume: If you add solute to 250 mL of water and then get a final volume of 260 mL, the molarity is based on 260 mL, not 250 mL. The calculator uses final volume.
  • Rounding too early: Rounding atomic weights to whole numbers (e.g., Cu=64) can cause a 0.5% error, which may be acceptable for rough work but not for precise solutions.
  • Ignoring significant figures: The calculator gives 4 decimal places, but your actual precision depends on your balance and glassware. Report results to the appropriate number of significant figures.

Related Calculations

Besides molarity, you might need to calculate percent composition, dilution factors, or the mass of copper in a sample. For percent composition, divide the mass of each element by the molar mass. For copper in CuSO4·5H2O:

%Cu = (63.546 / 249.69) × 100 = 25.45%.

For dilution, use the formula M1V1 = M2V2. The calculator on this page can help you find the initial concentration, then you can apply the dilution formula manually.

Safety and Handling

Copper sulfate is an irritant to skin and eyes, and it is harmful if swallowed. It is toxic to aquatic life. When handling the solid, wear gloves and safety goggles, and avoid inhaling dust. In case of contact, rinse with plenty of water. Always follow your lab method, the safety data sheet (SDS), and your supervisor. Do not dispose of copper sulfate solutions down the drain; collect them for proper hazardous waste disposal.

Frequently Asked Questions

What is the atomic mass of copper sulfate? (Answer: 159.61 g/mol for anhydrous, 249.69 g/mol for pentahydrate)

As stated, the anhydrous form has a molar mass of 159.61 g/mol, and the pentahydrate has 249.69 g/mol. The term “atomic mass” is often used loosely for “molar mass” of a compound, but strictly speaking, atomic mass applies to elements, not compounds.

Why is copper sulfate blue?

The blue color comes from the copper(II) ion (Cu2+) in aqueous solution, which absorbs light in the red part of the spectrum. The pentahydrate crystals are blue because of the water molecules in the crystal structure that coordinate with the copper ion.

How do I convert grams of copper sulfate to moles?

Divide the mass by the molar mass. For example, 10 g of anhydrous CuSO4 is 10 / 159.61 = 0.0626 mol. For the pentahydrate, 10 g is 10 / 249.69 = 0.0400 mol.

What is the difference between atomic mass and molar mass?

Atomic mass (or atomic weight) is the mass of a single atom, expressed in atomic mass units (u) or daltons (Da). Molar mass is the mass of one mole of a substance (6.022 × 1023 particles), expressed in g/mol. For a compound, the molar mass is the sum of the atomic masses of its constituent atoms, so numerically they are the same but with different units.

Can I use this calculator for other hydrates?

Yes, you can change the molar mass input to any compound’s molar mass. The calculator simply converts mass to moles and then to molarity. For example, for magnesium sulfate heptahydrate (MgSO4·7H2O), the molar mass is 246.47 g/mol, and you would enter that value.

Why does the calculator show 0.0468 mol/L for the default example?

Because 2.922 g of CuSO4·5H2O is about 0.0117 mol, and dissolving it in 0.250 L gives 0.0468 mol/L. This is a typical concentration for a 0.05 M solution, often used in qualitative analysis.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 249.69 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →