molecalculator

Moles & Molar Mass

Volume Calculator: Convert ft to Yards

Calculator No. 01-7482 · Updated · Formula and assumptions shown below

Volume in cubic yards 1.00 yd³
Volume in cubic inches
46,656 in³
= Volume in cubic feet × 1728
Volume in US gallons
201.97 gal
= Volume in cubic feet × 7.48052
Volume in cubic feet
27 ft³
Set in the form below
You enter
Volume in cubic feet (ft³)
You get
Volume in cubic yards (yd³), Volume in cubic inches (in³), Volume in US gallons (gal)
Rounding
2 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This volume calculator converts cubic feet (ft³) to cubic yards (yd³) instantly. You enter a volume in cubic feet, and the calculator gives you the equivalent volume in cubic yards. It also shows the result in cubic inches and gallons for easy reference.

Formula

The conversion is based on the relationship between feet and yards: 1 yard = 3 feet. When you cube this, you get 1 cubic yard = 27 cubic feet. Therefore, to convert cubic feet to cubic yards, divide by 27:

yd³ = ft³ / 27

Where:

  • yd³ = volume in cubic yards
  • ft³ = volume in cubic feet

For the reverse conversion, multiply cubic yards by 27 to get cubic feet.

Worked Example

Using the default value of 27 ft³:

  1. Divide the volume in cubic feet by 27: 27 / 27 = 1
  2. The result is 1 yd³.
  3. For cubic inches: 27 × 1728 = 46,656 in³ (since 1 ft³ = 1728 in³).
  4. For US gallons: 27 × 7.48052 ≈ 201.97 gal (using the conversion 1 ft³ = 7.48052 US gallons).

So, 27 cubic feet equals exactly 1 cubic yard, 46,656 cubic inches, and about 202 US gallons.

Assumptions

  • The conversion uses the standard definitions: 1 yard = 3 feet exactly.
  • The gallon output uses US liquid gallons (231 cubic inches), not imperial gallons.
  • All inputs are positive volumes; negative values are not meaningful in this context.

Why Convert Cubic Feet to Cubic Yards?

This conversion is essential in construction, landscaping, and earthwork. Materials like concrete, topsoil, mulch, gravel, and sand are often sold by the cubic yard, while project dimensions are measured in feet. For example, a concrete slab might be 10 ft long, 5 ft wide, and 0.5 ft thick. Its volume is 10 × 5 × 0.5 = 25 ft³, which is about 0.93 yd³. Knowing this helps you order the right amount of material and avoid over- or under-ordering.

How to Use the Calculator

Simply enter the volume in cubic feet into the input field. The calculator instantly shows the equivalent in cubic yards, cubic inches, and US gallons. Here are the steps:

  1. Measure the length, width, and height (or thickness) of your space in feet.
  2. Multiply these three numbers to get the volume in cubic feet.
  3. Enter that number into the calculator.
  4. Read the output: the first number is your volume in cubic yards.

For example, if you have a flower bed that is 6 ft long, 3 ft wide, and 1 ft deep, the volume is 18 ft³. Enter 18 to get 0.67 yd³.

Common Mistakes and Misconceptions

A frequent error is confusing cubic feet with square feet or linear feet. Cubic feet measure volume (length × width × height), while square feet measure area (length × width). For example, a patio 10 ft by 10 ft has an area of 100 ft², but if you want a 0.5 ft thick layer of gravel, the volume is 100 × 0.5 = 50 ft³, not 100 ft³.

Another mistake is forgetting to divide by 27. Some people mistakenly divide by 3, which would give a much larger number. Remember: 1 cubic yard = 27 cubic feet, not 3. This is because you are converting a three-dimensional measure.

Also, be careful with units when mixing feet and inches. Always convert inches to feet first (divide by 12) before calculating volume. For instance, a depth of 6 inches is 0.5 ft, not 6 ft.

Practical Applications

Here are common situations where this conversion is used:

  • Concrete orders: Ready-mix concrete is sold by the cubic yard. A typical driveway might need 10–15 yd³.
  • Landscaping: Mulch, soil, and compost are often sold in bags or bulk by the cubic yard. A 1-yd³ bag covers about 100 ft² at 3 inches deep.
  • Gravel and stone: For a patio base, you might need 2–3 yd³ of crushed stone.
  • Dumpster sizes: Dumpsters are sized in cubic yards, so knowing your waste volume helps you choose the right size.

Comparison with Other Units

While cubic yards are common in the US, other countries often use cubic meters. To convert cubic yards to cubic meters, multiply by 0.764554857984 (since 1 yd³ = 0.764554857984 m³). For example, 1 yd³ is about 0.765 m³. If you need to convert from cubic feet to cubic meters, divide by 35.3147. This calculator does not include metric conversions, but the formula is straightforward.

Limits of the Calculator

This calculator only handles volume conversion. It does not account for material density or weight. For example, a cubic yard of sand weighs about 2,700 lb, while a cubic yard of mulch weighs about 400 lb. If you need to know how much a material weighs, you must multiply the volume by its density. Also, the calculator uses US gallons; for imperial gallons, multiply the US gallon result by 0.832674.

Frequently Asked Questions

How many cubic feet are in a cubic yard?

There are exactly 27 cubic feet in 1 cubic yard. This comes from 1 yard = 3 feet, so 1 yd³ = 3 ft × 3 ft × 3 ft = 27 ft³.

Can I convert square feet to cubic yards?

No, not directly. Square feet measure area, cubic yards measure volume. To convert, you need a depth (height) to get volume. For example, if you have an area of 100 ft² and a depth of 0.5 ft, the volume is 50 ft³, which is about 1.85 yd³.

What is the difference between a yard and a cubic yard?

A yard is a linear measure (length). A cubic yard is a volume measure (length × width × height). For example, a yard of fabric is 3 feet long, but a cubic yard of soil is a cube that is 3 feet on each side.

How do I convert inches to feet for this calculator?

Divide the number of inches by 12. For example, 6 inches = 0.5 ft, 18 inches = 1.5 ft. Then multiply length, width, and height in feet to get cubic feet.

Is the calculator accurate for ordering concrete?

Yes, it gives the exact volume. However, concrete is usually ordered with a small extra amount (like 10%) to account for spillage, uneven subgrade, or rounding. Always confirm with your supplier.

Related

Formula used
in v | Volume in cubic feet | ft³ | 27 | 0
out yd | Volume in cubic yards | yd³ | v / 27 | 2
out in3 | Volume in cubic inches | in³ | v * 1728 | 0
out gal | Volume in US gallons | gal | v * 7.48052 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →