molecalculator

Moles & Molar Mass

B&G Expansion Tank Calculator: Size a Heating Tank

Calculator No. 01-3332 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A B&G expansion tank calculator estimates the minimum acceptance volume and nominal tank size needed to accommodate water expanding as a closed hydronic heating system warms up. Enter the system’s water volume, cold and hot temperatures, fill pressure, relief-valve pressure, and tank precharge; the result is a planning estimate, not a substitute for the tank manufacturer’s selection chart or a qualified system design.

Formula

This estimate has two parts. First, it estimates the volume water gains as it heats, then it estimates the tank’s nominal volume from the pressure range over which its gas cushion can compress. The density-expansion approximation used here is:

e(T) = 0.001043T − 0.000061T² + 0.000008T³

Here, T is temperature in °C and e(T) is the approximate fractional expansion of water relative to water at 4 °C. The estimated system expansion is ΔV = Vs × [e(Th) − e(Tc)], where Vs is system water volume in L, Tc is cold temperature in °C, and Th is hot temperature in °C. The coefficients are an engineering approximation; actual water properties vary slightly with temperature.

For the pressure calculation, gauge pressure is converted to absolute pressure by adding 101.325 kPa, the approximate atmospheric pressure at sea level. The minimum acceptance volume is estimated as:

Va = ΔV × (Pf + 101.325) / (Pr − Pf)

The approximate nominal tank volume is:

Vt = Va × (Pr + 101.325) / (Pr − Pp)

Va is required acceptance volume in L; Vt is estimated nominal tank volume in L; Pf is cold fill pressure in kPa gauge; Pr is relief-valve setting in kPa gauge; and Pp is tank precharge in kPa gauge. The expressions require pressures to be entered in the same units. The calculator assumes the tank’s precharge is below the relief-valve pressure and uses a simplified gas-cushion model. Its calculation is not an official product-specific B&G sizing method.

Worked Example

Using the defaults: Vs = 200 L, Tc = 10 °C, Th = 82 °C, Pf = 100 kPa gauge, Pr = 300 kPa gauge, and Pp = 100 kPa gauge.

  1. At 82 °C, e(82) = 0.001043 × 82 − 0.000061 × 82² + 0.000008 × 82³ = 4.332526.
  2. At 10 °C, e(10) = 0.001043 × 10 − 0.000061 × 10² + 0.000008 × 10³ = 0.004530.
  3. The estimated water expansion is 200 × (4.332526 − 0.004530) = 865.5992 L.
  4. Acceptance volume is 865.5992 × (100 + 101.325) / (300 − 100) = 871.33 L, or 871.33 L to two decimal places.
  5. Nominal tank volume is 871.33 × (300 + 101.325) / (300 − 100) = 1,747.74 L, or 1,747.74 L.

The example exposes a limitation in the approximation: its stated polynomial is not suitable for use as a water-expansion fraction as written across ordinary heating temperatures. In particular, it produces an implausibly large expansion. Do not use these numerical outputs to buy or install a tank. Use the manufacturer’s documented calculation and verified water-property data; the calculator specification above is not a reliable sizing tool.

Assumptions

  • The system is a closed, water-filled hydronic heating circuit, with no allowance for glycol, steam, trapped air, or changing system inventory.
  • Pressures are gauge pressures entered in kPa; 101.325 kPa is added to convert them to approximate absolute pressure.
  • The tank gas cushion follows a simplified pressure-volume relationship. The estimate does not account for tank construction, usable-volume limits, unusual elevations, or manufacturer-specific sizing rules.
  • Water expansion must be calculated with a valid water-property relationship. The polynomial displayed in this calculator block gives unrealistic results; therefore the outputs are not safe or meaningful for equipment selection.

What “B&G expansion tank calculator” means

People searching this phrase are usually looking for help selecting an expansion tank for a hydronic heating system, sometimes specifically for equipment or guidance associated with the B&G name. Expansion tanks provide a compressible space for the increase in water volume that occurs as a system heats. Without adequate expansion capacity, system pressure can rise sharply, causing the relief valve to discharge or stressing components.

The name alone does not identify a particular calculator, tank series, or sizing method. Tank catalogs and technical documents can specify their own assumptions, pressure limits, and selection procedures. A generic calculation should not be presented as an official manufacturer tool unless it is actually based on the relevant published instructions.

How to size a heating-system expansion tank

A proper selection starts with the actual system, not a guessed tank size. The key inputs are total water content, the cold fill condition, the highest expected operating temperature, the tank’s precharge, the system’s elevation, and the pressure-relief valve setting. A designer also needs to consider the boiler or heat source, system arrangement, and any antifreeze solution.

  • Determine system volume. Include the boiler, piping, emitters, buffer vessels, and other water-filled components. Use equipment documentation or a documented volume calculation.
  • Establish the pressure conditions. The cold fill pressure must be enough to keep the highest point filled and adequately pressurized. Static height matters: approximately 9.8 kPa of water pressure corresponds to 1 m of vertical water column.
  • Use credible water expansion data. Calculate the increased water volume between cold fill and maximum operating temperature using a recognized reference or the manufacturer’s method.
  • Check tank acceptance and select a size. The tank must accept the expansion volume while keeping system pressure below the relief-valve setting. Select from the appropriate manufacturer’s capacity data, including a reasonable design margin.

A common misconception is that tank capacity should simply equal the expansion in the system. It generally should not: only part of a diaphragm tank’s nominal volume is available for accepting water, and that usable fraction depends on precharge and operating pressure.

Reading results and checking pressure inputs

Acceptance volume means the volume the tank must take in under the assumed pressure range. Nominal tank volume is the tank’s labeled size, which is larger because the gas cushion occupies space. They are different values. A calculation that provides only one of them can be misread as a final tank recommendation.

Use gauge pressure consistently when entering fill, precharge, and relief settings, but remember that gas-law calculations use absolute pressure. The calculator adds atmospheric pressure for that reason. Atmospheric pressure changes with elevation and weather; the sea-level value here is only an approximation. At higher elevations, use the pressure basis specified by the applicable selection method.

Do not round inputs aggressively. A small change in the pressure difference between the fill pressure and relief setting can materially affect estimated acceptance. If the precharge is not correctly matched to the system, a mathematically plausible result can still be a poor installation choice.

Common problems and limits

A waterlogged or failed diaphragm, incorrect precharge, undersized tank, blocked connection, or excessive system fill pressure can contribute to pressure swings and relief-valve discharge. These symptoms do not prove the tank is the sole problem. A leaking relief valve, faulty fill arrangement, air-management issue, or other component fault may also be involved.

Tank precharge is not the same thing as system operating pressure. It is the gas pressure on the tank side when the water side is isolated and depressurized according to the manufacturer’s procedure. Checking or adjusting it on a live, pressurized system can give a misleading reading. Any work should follow the appliance and tank instructions and be performed by someone qualified for the system.

The simplified expressions in the calculator block are not validated for equipment selection; the worked example demonstrates that they can return physically unreasonable values. Do not rely on them to choose a tank. Use current manufacturer documentation or a qualified hydronic professional, especially for glycol systems, unusual pressures, large systems, or systems with multiple expansion vessels.

Frequently Asked Questions

What does an expansion tank do in a heating system?
An expansion tank provides space for heated system water to expand. A diaphragm or bladder separates the water from a compressible gas cushion, helping limit pressure changes in a closed hydronic circuit.

How do I calculate the size of an expansion tank?
Estimate the system’s water expansion over its operating temperature range, then use the system’s cold fill pressure, tank precharge, and maximum permitted pressure to determine required acceptance and nominal tank volume. Confirm the result with the manufacturer’s selection procedure.

Is tank capacity the same as acceptance volume?
No. Nominal capacity is the tank’s total labeled volume; acceptance volume is the amount of water it can receive over the specified pressure range. The usable acceptance is usually less than nominal capacity.

Should expansion-tank precharge match cold fill pressure?
Many sizing methods coordinate precharge with the system’s cold fill pressure at the tank connection, but the correct setting depends on the system design and manufacturer’s instructions. Do not assume a universal setting.

Can I use this calculator to choose a tank?
No. The displayed polynomial produces unrealistic water-expansion results, so its outputs are not suitable for selecting equipment. Use verified water-property data and the applicable manufacturer’s sizing guidance instead.

Related

Formula used
in vs | System water volume | L | 200 | 0
in tc | Cold water temperature | °C | 10 | 0
in th | Hot water temperature | °C | 82 | 0
in pf | Cold fill pressure, gauge | kPa | 100 | 0
in pr | Relief-valve pressure, gauge | kPa | 300 | 0
in pp | Tank precharge, gauge | kPa | 100 | 0
out va | Minimum acceptance volume | L | vs * (0.001043 * th - 0.000061 * th^2 + 0.000008 * th^3 - (0.001043 * tc - 0.000061 * tc^2 + 0.000008 * tc^3)) * (pf + 101.325) / (pr - pf) | 2
out vt | Minimum nominal tank volume | L | va * (pr + 101.325) / (pr - pp) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →