A beam analysis calculator determines the internal bending moment, shear force, and deflection of a beam under specified loads and support conditions. You enter the beam length, support type, load magnitude and position, and material properties, and it returns the maximum shear force, maximum bending moment, and maximum deflection, along with their locations along the beam.
Formula
For a simply supported beam with a uniformly distributed load (UDL), the standard formulas are:
- Maximum shear force at the supports: Vmax = w·L / 2
- Maximum bending moment at midspan: Mmax = w·L² / 8
- Maximum deflection at midspan: δmax = 5·w·L⁴ / (384·E·I)
Where:
- w = uniform load per unit length (kN/m)
- L = beam length (m)
- E = modulus of elasticity (GPa, converted to Pa: multiply by 10⁹)
- I = area moment of inertia (cm⁴, converted to m⁴: multiply by 10⁻⁸)
These formulas assume linear elastic material, small deflections, and a prismatic beam (constant cross-section).
Worked Example
Using the default values: L = 6 m, w = 10 kN/m, E = 200 GPa, I = 8000 cm⁴.
Step 1 – Maximum shear force:
Vmax = (10 kN/m × 6 m) / 2 = 30 kN
Step 2 – Maximum bending moment:
Mmax = (10 kN/m × (6 m)²) / 8 = (10 × 36) / 8 = 45 kN·m
Step 3 – Maximum deflection:
Convert E: 200 GPa = 200 × 10⁹ Pa
Convert I: 8000 cm⁴ = 8000 × 10⁻⁸ m⁴ = 8 × 10⁻⁵ m⁴
δmax = (5 × 10 × 6⁴) / (384 × 200×10⁹ × 8×10⁻⁵)
= (5 × 10 × 1296) / (384 × 1.6×10⁷)
= 64800 / 6.144×10⁹ = 1.0547×10⁻⁵ m = 10.547 mm ≈ 10.55 mm
The calculator shows Vmax = 30.00 kN, Mmax = 45.00 kN·m, and δmax = 10.55 mm, matching the hand calculation.
Assumptions
- Beam is straight, prismatic, and made of homogeneous isotropic material.
- Loads are static and applied perpendicular to the beam axis.
- Material behaves linearly elastically (stress proportional to strain).
- Deflections are small compared to beam length.
- Shear deformations are neglected (valid for slender beams with length-to-depth ratio > 10).
- The self-weight of the beam is either negligible or included in the uniform load w.
How to Use the Results
The three output values serve different design checks:
- Shear force – compare with the shear capacity of the cross-section (e.g., 0.6 × yield strength × web area for steel). If Vmax exceeds capacity, the beam may fail by shear near supports.
- Bending moment – compare with the moment capacity (e.g., plastic moment for steel, or allowable stress × section modulus for timber). This is the primary strength check for most beams.
- Deflection – compare with serviceability limits. Common limits are L/250 for floors (≈ 24 mm for a 6 m span) or L/360 for brittle finishes (≈ 16.7 mm). Our example gives 10.55 mm, which passes both.
Always check both strength and deflection – a beam can be strong enough but too flexible for comfort.
Common Mistakes and Pitfalls
- Unit mix-ups: The most frequent error. Ensure E is in Pa (not GPa), I in m⁴ (not cm⁴), and w in N/m (not kN/m) when using the deflection formula. Our calculator handles conversions internally, but manual checks often fail here.
- Confusing support types: A cantilever with the same load has Mmax = w·L²/2 (four times larger) and deflection = w·L⁴/(8·E·I) (about 9.6 times larger). Always verify the support condition.
- Ignoring load combination: Real beams often have point loads plus UDL. The maximum moment is not simply the sum of individual maxima – you must find the location where the total moment is largest.
- Rounding too early: In the deflection formula, rounding E or I prematurely can change the result by several percent. Keep at least three significant figures in intermediate steps.
- Using the wrong I: The moment of inertia depends on the bending axis. For a rectangular section, I = b·h³/12 about the horizontal axis, but b³·h/12 about the vertical axis. Use the one corresponding to the direction of bending.
When to Use More Advanced Analysis
The simple formulas above only cover simply supported beams with UDL. For other cases, you need different equations:
- Point loads: For a central point load P, Mmax = P·L/4 and δmax = P·L³/(48·E·I).
- Cantilevers: For a UDL, Mmax = w·L²/2 (at the fixed end), δmax = w·L⁴/(8·E·I).
- Propped cantilevers or continuous beams: Use the moment distribution method or finite element software.
- Non-uniform cross-sections: Use numerical integration (e.g., virtual work) or FEA.
For preliminary design, many engineers use superposition: calculate the moment and deflection from each load separately, then add them algebraically. This works only for linear elastic behavior.
Safety and Design Considerations
Beam analysis is a planning tool, not a substitute for professional engineering judgment. Always follow your local building codes and standards (e.g., Eurocode, AISC, ACI) which include safety factors, load combinations, and material reduction factors. The calculated values are unfactored – real design multiplies loads by factors (typically 1.2–1.6) and divides material strengths by factors (typically 1.5–1.15).
For critical structures, have a licensed structural engineer review the analysis. The calculator assumes ideal supports, but real connections have some flexibility. Also consider lateral-torsional buckling for slender steel beams, local buckling of thin flanges, and fire resistance – none of which are captured by simple bending formulas.
Frequently Asked Questions
What is the difference between a beam analysis and a beam design calculator?
Analysis calculates the internal forces and deflections for a given beam and loading. Design selects a cross-section that can safely resist those forces. This page performs analysis; design would require iterating: choose a section, compute stresses, compare with allowable, and adjust.
Can I use this calculator for a point load instead of a uniform load?
No – the formulas shown are specifically for a uniformly distributed load. For a central point load, use Mmax = P·L/4 and δmax = P·L³/(48·E·I). Many online calculators offer multiple load types; this one is limited to UDL.
What if my beam has multiple loads?
For linear elastic behavior, you can use superposition: calculate the moment and deflection from each load separately (using the appropriate formula for each), then sum the results. The maximum total moment may not occur at midspan – evaluate at several points along the beam.
How do I find the moment of inertia for a standard steel beam?
For standard I-beams, the moment of inertia is tabulated in manufacturer catalogs and structural steel handbooks. For a rectangular section, use I = b·h³/12, where b is the width and h is the depth. For a circular section, I = π·d⁴/64.
Why does my deflection calculation give a different answer than a finite element program?
Finite element software often includes shear deformation, which increases deflection slightly for short beams. For slender beams (span/depth > 10), the difference is usually under 1%. Also check units – many programs expect E in Pa and I in m⁴.
Is the deflection limit always L/360?
No – L/360 is a common limit for floors supporting plaster ceilings, but other limits apply: L/240 for roof beams, L/180 for cantilevers, and L/600 for precision machinery supports. Check your applicable building code for the specific limit.
Related
Formula used
in m | Beam length | m | 6 | 0.1 in w | Uniform load | kN/m | 10 | 0 in E | Modulus of elasticity | GPa | 200 | 1 in I | Moment of inertia | cm^4 | 8000 | 1 out Vmax | Max shear force | kN | w * m / 2 | 2 out Mmax | Max bending moment | kN·m | w * m^2 / 8 | 2 out dmax | Max deflection | mm | (5 * w * m^4 * 1000) / (384 * E * 1e9 * I * 1e-8) * 1000 | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- QPP Calculator Canada: How It Works & How to Use It
- PPP Calculator World Bank: How It Works & How to Use It2,000.00
- PPP Calculator: India vs USA Cost Comparison1,000.00 USD
- PPP Calculator USD to INR: How It Works2,335 INR
- PPP Calculator India vs UK: Real Cost Comparison103.63 GBP
- PPP Calculator India vs Dubai: Real Cost Comparison8,954.58 AED