molecalculator

Moles & Molar Mass

Enthalpy of Combustion: How to Measure It

Calculator No. 01-9803 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To measure the enthalpy of combustion in a practical setting, you burn a known mass of a substance in a calorimeter, measure the temperature change of a known mass of water, and then calculate the heat released using q = mcΔT. This article explains the practical procedure, the calculations involved, and the common sources of error that make classroom results differ from published values.

Formula

The enthalpy of combustion (ΔHc) is the heat released when one mole of a substance is completely burned in oxygen under standard conditions. In a simple practical, you measure the heat absorbed by water and then divide by the moles of fuel burned.

Heat absorbed by water: q = mwater × cwater × ΔT

  • q – heat energy absorbed by the water (J)
  • mwater – mass of water (g)
  • cwater – specific heat capacity of water (4.18 J/(g·°C))
  • ΔT – temperature rise of the water (°C)

Enthalpy of combustion per mole: ΔHc = −q / n (negative because heat is released)

  • n – moles of fuel burned = mass of fuel (g) / molar mass (g/mol)

Worked Example

Using the default values from the calculator: 0.500 g of fuel burned, 100.0 g of water, temperature rise 12.5 °C, c = 4.18 J/(g·°C).

  1. Calculate heat absorbed by water: q = 100.0 g × 4.18 J/(g·°C) × 12.5 °C = 5225 J = 5.225 kJ
  2. If the fuel is ethanol (molar mass 46.07 g/mol), moles burned = 0.500 g / 46.07 g/mol = 0.01085 mol
  3. Enthalpy of combustion per mole = −5.225 kJ / 0.01085 mol = −481.6 kJ/mol (experimental)

The calculator’s first output (q) gives 5225 J, matching the manual calculation.

Assumptions

  • All heat released by the fuel goes into the water (no heat loss to the surroundings).
  • The specific heat capacity of water is constant over the temperature range (4.18 J/(g·°C)).
  • Complete combustion of the fuel occurs.
  • The calorimeter itself absorbs negligible heat.
  • The density of water is 1.00 g/mL, so volume in mL equals mass in g.

Practical Setup: What You Need

A typical school or college practical uses a simple “copper can” calorimeter. The apparatus includes:

  • A spirit burner or small lamp containing the liquid fuel (e.g., ethanol, propanol, hexane).
  • A copper or aluminium can filled with a known volume of water (usually 100–200 mL).
  • A thermometer or temperature probe reading to 0.1 °C or better.
  • A balance accurate to 0.01 g for weighing the fuel before and after burning.
  • A draught shield to reduce air currents and heat loss.

Procedure: weigh the burner with fuel, measure the water volume and initial temperature, light the burner, stir the water gently, and extinguish when the temperature has risen by about 10–20 °C. Record the final temperature and reweigh the burner. The mass difference is the fuel burned.

Calculating the Enthalpy Change

Once you have the raw data, the calculation proceeds in three steps:

  1. Calculate the heat absorbed by the water: q = mwater × cwater × ΔT.
  2. Convert q to kJ (divide by 1000).
  3. Divide by the moles of fuel burned (mass burned / molar mass) to get ΔHc in kJ/mol.

Because heat is released, the sign is negative. For example, the theoretical ΔHc of ethanol is about −1367 kJ/mol, but a simple calorimeter often gives values around −400 to −600 kJ/mol due to heat losses.

Common Problems and How to Minimize Them

Classroom results are notoriously lower than literature values. The main reasons are:

  • Heat loss to the surroundings – the biggest error. Use a draught shield, keep the flame close to the can, and stir continuously.
  • Incomplete combustion – a yellow, sooty flame means incomplete burning. Ensure a good air supply and use a clean wick.
  • Evaporation of water – some water evaporates during heating, which removes heat. Covering the can with a lid reduces this but also traps the flame gases.
  • Heat absorbed by the calorimeter – the metal can also warms up. A simple correction is to include the heat capacity of the can in the calculation, but many practicals ignore it.
  • Weighing errors – fuel evaporates from the wick between weighings. Weigh the burner quickly and keep it capped when not in use.

To improve accuracy, you can use a bomb calorimeter (constant volume) which eliminates most heat loss, but that is beyond a typical school lab.

Comparing Fuels: Which Alcohol is Best?

A common extension is to compare the enthalpy of combustion of different alcohols (methanol, ethanol, propanol, butanol). The trend is that as the molar mass increases, the enthalpy of combustion per mole becomes more negative (more energy released). For example, methanol ≈ −726 kJ/mol, ethanol ≈ −1367 kJ/mol, propan-1-ol ≈ −2021 kJ/mol, butan-1-ol ≈ −2676 kJ/mol (theoretical).

When comparing fuels, you might also calculate the energy per gram (specific energy). This shows that lighter fuels like methanol release more energy per gram than heavier ones, even though they have lower energy per mole. This is why the calculator includes a per-gram output.

Frequently Asked Questions

Why is my measured enthalpy of combustion lower than the theoretical value?

Heat is lost to the surroundings, some fuel may not burn completely, and the calorimeter absorbs heat. These losses mean less heat reaches the water, so the calculated ΔHc appears less negative (smaller magnitude).

How do I convert from kJ/g to kJ/mol?

Multiply the value in kJ/g by the molar mass of the substance in g/mol. For example, if ethanol gives 30 kJ/g, then per mole: 30 × 46.07 = 1382 kJ/mol (approximately).

What is the difference between enthalpy of combustion and heat of combustion?

They are essentially the same. “Heat of combustion” is an older term; enthalpy of combustion is the modern term used when the process occurs at constant pressure (as in an open calorimeter).

Can I use this method for solid fuels like wax or sugar?

Yes, but you need a different burner or a crucible. The principle is the same: weigh the solid fuel, burn it under the calorimeter, and measure the temperature rise. Solids often burn less cleanly, so errors are larger.

Why does the calculator ask for the mass of fuel burned, not the initial mass?

You need the mass that actually burned, which is the difference between the initial and final mass of the fuel container. This is the mass that produced the heat measured.

What is the standard enthalpy of combustion?

It is the enthalpy change when one mole of a substance is completely burned in oxygen under standard conditions (298 K, 1 atm, all substances in their standard states). These values are tabulated and are usually more negative than experimental values from simple calorimetry.

Safety and Best Practice

When doing a combustion practical, always follow your lab method, the safety data sheet (SDS) and your supervisor. Alcohols are flammable, so keep them away from naked flames when not in use. Use a safety screen, tie back long hair, and never leave a burning burner unattended. Ensure good ventilation to avoid inhaling combustion products.

Related

Formula used
in m | Mass of fuel burned | g | 0.500 | 0
in w | Mass of water | g | 100.0 | 0
in dt | Temperature rise of water | °C | 12.5 | 0
in cw | Specific heat capacity of water | J/(g·°C) | 4.18 | 0
out q | Heat absorbed by water | J | m * cw * dt | 0
out qk | Heat absorbed by water | kJ | q / 1000 | 2
out dh | Enthalpy of combustion (per gram) | kJ/g | q / (m / 1000) / 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →