molecalculator

Moles & Molar Mass

C1V1 = C2V2 Equation Name & How to Use It

Calculator No. 01-9215 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator applies the dilution equation C1V1 = C2V2 (also called the dilution formula or the concentration-volume equation) to find any one of the four variables when the other three are known. You enter the initial concentration and volume and the final concentration (or volume), and the calculator returns the missing final volume (or concentration) in your choice of molarity, millimolar, or other units. The equation itself is a simple conservation statement: the amount of solute (concentration × volume) stays the same before and after dilution.

Formula

In words: the concentration of the stock solution times its volume equals the concentration of the diluted solution times its final volume. In symbols:

C1 × V1 = C2 × V2

  • C1 – concentration of the stock (initial) solution, in any concentration unit (mol/L, mM, % w/v, etc.)
  • V1 – volume of the stock solution taken, in any volume unit (mL, L, µL)
  • C2 – final concentration after dilution, in the same unit as C1
  • V2 – final total volume after dilution, in the same unit as V1

The only requirement is that the units on each side match: C1 and C2 must be the same unit, and V1 and V2 must be the same unit. The equation does not care whether you use mL or L, as long as both volumes use the same unit.

Worked Example

Suppose you need to prepare 250 mL of a 0.200 mol/L NaCl solution from solid NaCl (molar mass 58.44 g/mol). First, find the mass of solute needed using the molarity definition:

Moles of NaCl = C × V = 0.200 mol/L × (250/1000) L = 0.0500 mol

Mass = moles × molar mass = 0.0500 mol × 58.44 g/mol = 2.922 g

So you dissolve 2.922 g of NaCl in enough water to make a final volume of 250 mL. The calculator above uses exactly this calculation: 2.922 g ÷ 58.44 g/mol ÷ (250/1000) L = 0.2000 mol/L, which is 200.0 mM. Notice the final volume is the total volume of the solution, not the volume of water added.

Assumptions

  • The solute is non-volatile and does not react with the solvent.
  • The solution is ideal: volumes are additive and the density change is negligible (true for dilute aqueous solutions).
  • When dissolving a solid, the final volume is measured after the solute is fully dissolved, not the volume of solvent used.
  • For dilutions, the amount of solute in V1 is exactly the amount in V2 – no loss, no added solute.

When to Use C1V1 = C2V2

This equation is used whenever you dilute a concentrated stock solution to a lower concentration, or when you concentrate a solution by evaporation (though in practice it is used almost exclusively for dilutions). Typical lab situations include:

  • Preparing a working solution from a 1 M stock (e.g., diluting 5 M NaCl to 0.5 M).
  • Making serial dilutions for standard curves in spectroscopy or ELISA.
  • Diluting a concentrated acid or base to a safer concentration (always add acid to water).
  • Adjusting the concentration of a buffer or media component.

The equation also works in reverse: if you know the final concentration and volume you want, and the stock concentration, you can solve for V1 – the volume of stock to pipette.

How to Use the Calculator

This particular calculator is designed for a slightly different but related task: preparing a solution from a solid solute. You enter the mass of solute, its molar mass, and the final volume, and it gives the molarity. To use the C1V1 equation directly, you would enter the stock concentration and volume on one side and the final concentration on the other. For example, to find how much 5 M NaCl stock to use to make 500 mL of 0.2 M NaCl:

  1. Identify C1 = 5 M, C2 = 0.2 M, V2 = 500 mL.
  2. Rearrange: V1 = (C2 × V2) / C1 = (0.2 × 500) / 5 = 20 mL.
  3. Pipette 20 mL of stock into a graduated cylinder and add water to a final volume of 500 mL.

If you instead have a solid, use the mass-based calculation above.

Common Mistakes and Pitfalls

  • Unit mismatch: Mixing mL and L on the same side. Always convert so that V1 and V2 share the same unit.
  • Concentration unit confusion: Using molarity for C1 and percent for C2 without conversion. The equation only works if C1 and C2 are in the same unit.
  • Final volume vs. added solvent: For a dilution, V2 is the final total volume (stock + diluent), not the volume of diluent added. For example, 20 mL stock + 480 mL water gives V2 = 500 mL, not 480 mL.
  • Forgetting to account for the volume of solute: When dissolving a solid, the final volume is not the volume of water you start with; you must add solute and then adjust to the final volume.
  • Rounding too early: Keep extra digits until the final answer.

Limitations and Alternatives

C1V1 = C2V2 assumes that the volumes are additive and that the concentration is uniform. This is a good approximation for dilute solutions, but it fails for concentrated solutions where the density changes significantly (e.g., mixing ethanol and water causes volume contraction). In such cases, you must use mass-based calculations or account for density. Also, the equation does not handle situations where the solute reacts with the solvent or where the concentration is expressed in molality (moles per kg of solvent) – for molality you need a different approach.

For serial dilutions, you can apply the equation repeatedly, but it is often easier to use a dilution factor (e.g., 1:10 dilution) and multiply the concentration step by step.

Frequently Asked Questions

What does C1V1 = C2V2 stand for?

C stands for concentration, V for volume. The subscripts 1 and 2 refer to the initial (stock) and final (diluted) solutions. The equation states that the product of concentration and volume (which equals the amount of solute) is constant before and after dilution.

Can I use C1V1 = C2V2 with percent concentrations?

Yes, as long as both concentrations are in the same unit (e.g., both % w/v or both % v/v). If you have a 10% stock and want a 2% solution, you can use 10 × V1 = 2 × V2. However, be careful with % w/v vs % v/v – they are not interchangeable.

What if I don’t know the molar mass?

If you are working with a stock solution and diluting it, you don’t need the molar mass at all – the equation works with any concentration unit. The molar mass is only needed when preparing a solution from a solid (as in the calculator above).

Is C1V1 = C2V2 the same as the dilution formula?

Yes, it is often called the dilution formula or the dilution equation. It is a specific case of the general conservation of mass applied to solutions.

Does the equation work for gases?

It can be used for gas dilutions if you assume ideal behavior and constant temperature and pressure, but for gases you usually use the ideal gas law (PV = nRT) to relate volume and moles. For solutions, C1V1 = C2V2 is standard.

Why is the final volume not just the volume of water added?

Because the solute itself occupies volume. When you add 20 mL of stock to 480 mL of water, the total volume is not exactly 500 mL due to molecular interactions, but for dilute aqueous solutions the difference is negligible. In precise work, you make up to the final volume in a volumetric flask.

Follow your lab method, the safety data sheet (SDS) and your supervisor when preparing any chemical solution.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →