molecalculator

Moles & Molar Mass

C1V1 = C2V2 Percent: How to Use It

Calculator No. 01-10164 · Updated · Formula and assumptions shown below

Final volume (V2) 25.00 mL
Initial concentration (C1)
10 %
Set in the form below
Initial volume (V1)
5 mL
Set in the form below
Final concentration (C2)
2 %
Set in the form below
You enter
Initial concentration (C1) (%), Initial volume (V1) (mL), Final concentration (C2) (%)
You get
Final volume (V2) (mL)
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This page explains the C1V1 = C2V2 equation, a standard formula for calculating dilutions, and shows how to express the result as a percent concentration. You enter the initial concentration (C1), initial volume (V1), and either the final concentration or final volume, and the calculator returns the missing value, which you can then read as a percentage.

Formula

The dilution equation is written as:

C1 × V1 = C2 × V2

  • C1 = initial concentration (any unit, here % w/v)
  • V1 = initial volume (mL)
  • C2 = final concentration (same unit as C1)
  • V2 = final volume (mL)

To solve for V2: V2 = (C1 × V1) / C2. The equation assumes that the amount of solute (C × V) stays constant during dilution – you are only adding more solvent.

Worked Example

Using the defaults: C1 = 10%, V1 = 5 mL, C2 = 2%.

  1. Multiply C1 by V1: 10 × 5 = 50 (%·mL)
  2. Divide by C2: 50 / 2 = 25 mL

So V2 = 25 mL. This means you would add enough water to bring the total volume to 25 mL. The final solution has a concentration of 2% (w/v), and the percent is simply the C2 value.

Assumptions

  • The solute amount (mass or moles) is conserved – no reaction occurs.
  • Volumes are additive (usually true for dilute aqueous solutions).
  • Concentration units are consistent – both C1 and C2 are in the same unit (e.g., % w/v, mol/L, mg/mL).
  • Temperature is constant; density changes are negligible.

How to Choose the Right Concentration Unit

The equation works with any concentration unit as long as you use the same unit for C1 and C2. Common choices:

  • Percent (% w/v): grams of solute per 100 mL of solution.
  • Molarity (mol/L): moles of solute per liter.
  • Mass/volume (mg/mL): often used in biology.

If you need a percent result, simply use percent as your unit. For example, a 10% stock solution means 10 g of solute in 100 mL final volume.

Common Mistakes and How to Avoid Them

  • Mixing units: If C1 is in % but C2 is in mol/L, the equation gives nonsense. Always convert first.
  • Adding solvent instead of making final volume: The equation gives the total final volume (V2), not the amount of solvent to add. To find solvent to add, subtract V1 from V2.
  • Forgetting that percent is per 100 mL: A 5% solution has 5 g per 100 mL, not per 1 mL.
  • Rounding too early: Keep extra digits until the final step to avoid error.

When to Use This Equation

Use C1V1 = C2V2 whenever you dilute a stock solution to a lower concentration. Common scenarios:

  • Preparing a working solution from a concentrated stock (e.g., diluting 10% to 2%).
  • Serial dilutions in the lab.
  • Adjusting concentrations in buffers or media.

It does not apply when you need to account for chemical reactions, density changes, or non-ideal mixing.

Limitations of the Formula

The equation assumes ideal mixing and constant density. For very concentrated solutions (e.g., >10% w/v), volumes may not be perfectly additive, and the final concentration may differ slightly from the calculated value. For precise work, prepare by mass or use a volumetric flask. Also, the equation only works for dilutions – it cannot predict the concentration after a chemical reaction.

Frequently Asked Questions

What does C1V1 = C2V2 mean?

It means that the product of concentration and volume before dilution equals the product after dilution, because the amount of solute is unchanged.

How do I get a percent from C1V1 = C2V2?

The percent is simply the concentration value you use. If you set C1 and C2 as percentages, then C2 is the final percent concentration. For example, if C2 = 2, the final solution is 2%.

Can I use this for molarity?

Yes, the equation works for molarity (mol/L) exactly the same way. Just make sure both concentrations are in mol/L.

What if I don’t know V2 but I know how much solvent to add?

If you know the volume of solvent to add (let’s call it A), then V2 = V1 + A. You can rearrange to solve for C2: C2 = (C1 × V1) / (V1 + A).

Does this work for serial dilutions?

Yes, you can apply the equation step by step. For each step, use the previous concentration as C1 and the new total volume as V2.

Is there a difference between % w/v and % v/v?

Yes. % w/v is grams per 100 mL (mass/volume), while % v/v is mL per 100 mL (volume/volume). The equation works for both, but you must keep the same type throughout.

Related

Formula used
in c1 | Initial concentration (C1) | % | 10 | 0
in v1 | Initial volume (V1) | mL | 5 | 0
in c2 | Final concentration (C2) | % | 2 | 0
out v2 | Final volume (V2) | mL | c1 * v1 / c2 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →