An uncertainty analysis calculator estimates the combined uncertainty of a calculated result from the uncertainties of its input measurements, typically using the propagation of uncertainty formula. You enter the value and uncertainty for each input, and the calculator returns the result with its combined standard uncertainty and expanded uncertainty. This page explains the method, provides a working calculator for the most common case (multiplication and division), and walks through a worked example.
Formula
For a result R calculated from independent inputs a, b, c, …, the combined standard uncertainty is:
uc(R) = √[ (∂R/∂a · ua)² + (∂R/∂b · ub)² + (∂R/∂c · uc)² + … ]
where ∂R/∂a is the partial derivative of R with respect to a, and ua is the standard uncertainty of a. For the special case R = x·y (multiplication or division), the relative combined uncertainty is:
(uc/R) = √[ (ux/x)² + (uy/y)² ]
In the calculator above, the first output computes uc = √[(ux/x)² + (uy/y)²] · |x·y|, which is the standard uncertainty of the product. The second output multiplies by 2 to give the expanded uncertainty for a 95% confidence level (coverage factor k=2). The third output expresses the combined uncertainty as a percentage of the result.
Worked Example
Suppose you measure the length of a rectangle as x = 10.0 cm with a standard uncertainty ux = 0.1 cm, and the width as y = 5.0 cm with uy = 0.05 cm. The area is R = x·y = 10.0 × 5.0 = 50.0 cm².
Using the relative uncertainty formula:
(ux/x)² = (0.1/10.0)² = (0.01)² = 0.0001
(uy/y)² = (0.05/5.0)² = (0.01)² = 0.0001
Sum = 0.0002
√0.0002 = 0.014142
uc = 0.014142 × 50.0 = 0.7071 cm²
Expanded uncertainty (k=2): 0.7071 × 2 = 1.414 cm². So the area is reported as 50.0 ± 1.4 cm² (or 50.0 ± 1.4 cm², k=2). The relative uncertainty is 0.7071/50.0 × 100 = 1.41%.
Assumptions
- Input uncertainties are standard uncertainties (one standard deviation).
- Inputs are independent (no correlation between them).
- The formula is linearized using a first-order Taylor series approximation, which is valid for small uncertainties relative to the values.
- The expanded uncertainty uses a coverage factor k=2, which corresponds to approximately 95% confidence only if the distribution is approximately normal.
When to Use Uncertainty Analysis
Uncertainty analysis is used whenever a result is derived from multiple measurements, each with its own error. Common situations include:
- Calculating concentration from mass and volume (e.g., preparing a solution).
- Determining density from mass and volume measurements.
- Computing reaction rates from time and concentration data.
- Calibrating instruments using a standard reference.
- Estimating the error in a derived quantity in physics or engineering labs.
The goal is to quantify how the errors in the inputs propagate to the final result, so you can report a realistic confidence interval. This is essential in scientific reporting, quality control, and any field where measurement accuracy matters.
How to Read the Results
The combined standard uncertainty (uc) is the standard deviation of the result due to the input uncertainties. The expanded uncertainty (U = k·uc) defines an interval around the result (result ± U) that should contain the true value with a certain confidence level (usually 95% for k=2). The relative uncertainty gives the error as a percentage, which is useful for comparing precision across different scales.
For example, if you report a concentration as 0.250 ± 0.004 mol/L (k=2), it means the true value is likely between 0.246 and 0.254 mol/L. If the relative uncertainty is 1.6%, you know the measurement is precise to about 1.6% of the value.
Common Mistakes and Misconceptions
One common mistake is adding absolute uncertainties directly (e.g., 0.1 + 0.05 = 0.15) instead of using the quadratic sum. For multiplication and division, you must combine relative uncertainties in quadrature. Another error is using the expanded uncertainty (k=2) as if it were a standard uncertainty; always keep track of which one you are using.
A frequent misconception is that the uncertainty of a sum is the sum of uncertainties. In fact, for addition/subtraction, the combined uncertainty is the square root of the sum of squares of the individual uncertainties (if independent). For multiplication/division, you combine relative uncertainties. The calculator above handles the multiplication/division case.
Also, be careful with units: the uncertainties must be in the same units as the values. If you mix centimeters and meters, the relative uncertainties will be wrong.
Limitations of the Formula
The propagation formula assumes that the uncertainties are small enough that the linear approximation is valid. For large uncertainties (e.g., >10-20% of the value), the linear approximation may break down, and a Monte Carlo simulation would be more accurate. It also assumes the inputs are independent; if there is correlation, the formula needs covariance terms. Finally, the coverage factor k=2 gives approximately 95% confidence only when the result has a normal distribution; for small sample sizes or non-normal distributions, the confidence level may differ.
Alternatives to the Calculator
If you have more than two inputs, you can extend the formula manually by adding more terms under the square root. For complex functions, you can use numerical methods such as Monte Carlo simulation, where you randomly sample input values from their uncertainty distributions and compute the distribution of results. Some spreadsheet software and statistical packages have built-in uncertainty propagation functions. However, for simple products, this calculator gives the same result as those methods.
Frequently Asked Questions
What is the difference between standard uncertainty and expanded uncertainty?
Standard uncertainty (u) is the estimated standard deviation of the measurement. Expanded uncertainty (U) is the standard uncertainty multiplied by a coverage factor (k), typically k=2 for 95% confidence. The expanded uncertainty defines an interval around the result that is expected to contain the true value with the stated confidence level.
How do I know if my uncertainties are independent?
Independence means that the error in one input does not affect the error in another. For example, if you measure length and width with the same ruler, they might be correlated if the ruler has a systematic bias. In practice, if the measurements are made with different instruments or at different times, they are usually independent. If they are correlated, you need to include covariance terms, which is beyond this calculator.
Can I use this for addition and subtraction?
No, this calculator is specifically for multiplication and division. For addition and subtraction, the combined uncertainty is the square root of the sum of squares of the absolute uncertainties: uc = √(ua² + ub²). You can use that formula directly.
What if my uncertainty is given as a range (e.g., ±0.2)?
If the range is given as a confidence interval, you need to convert it to a standard uncertainty. For a 95% confidence interval, divide the half-width by 1.96 (or 2 for a rough estimate). For a maximum error (uniform distribution), divide by √3. Use the resulting standard uncertainty in the calculator.
Why is the relative uncertainty used for multiplication?
Because when you multiply or divide, the relative errors add in quadrature. Intuitively, a 1% error in one factor and a 2% error in another factor give a combined error of about √(1²+2²) ≈ 2.2%, not 3%. This is why the calculator uses relative uncertainties.
Does the calculator work for division too?
Yes, the formula is the same for division. If R = x/y, the relative uncertainty is still √[(ux/x)² + (uy/y)²]. The calculator multiplies the relative uncertainty by the absolute value of the result, so it works for both multiplication and division.
Related
Formula used
in x | Value of x | - | 10.0 | -1000000 in ux | Uncertainty of x (u_x) | - | 0.1 | 0 in y | Value of y | - | 5.0 | -1000000 in uy | Uncertainty of y (u_y) | - | 0.05 | 0 out uc | Combined standard uncertainty (u_c) | - | sqrt((ux/x)^2 + (uy/y)^2) * abs(x*y) | 4 out uexp | Expanded uncertainty (k=2) | - | uc * 2 | 4 out rel | Relative uncertainty (%) | - | uc / abs(x*y) * 100 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- QPP Calculator Canada: How It Works & How to Use It
- PPP Calculator World Bank: How It Works & How to Use It2,000.00
- PPP Calculator: India vs USA Cost Comparison1,000.00 USD
- PPP Calculator USD to INR: How It Works2,335 INR
- PPP Calculator India vs UK: Real Cost Comparison103.63 GBP
- PPP Calculator India vs Dubai: Real Cost Comparison8,954.58 AED