Calculate concentration from absorbance with the Beer–Lambert law: divide the measured absorbance by the substance’s molar absorptivity and the optical path length. Enter those three values to get concentration in mol/L; the result is valid only when the wavelength, units, sample conditions, and calibration assumptions are appropriate.
Formula
The Beer–Lambert law is A = εlc. Rearranged to find concentration: c = A / (εl).
- A is absorbance, dimensionless (often reported as AU).
- ε is molar absorptivity, in L/(mol·cm), for the absorbing substance at the measurement wavelength and under specified conditions.
- l is the optical path length through the sample, in cm.
- c is concentration, in mol/L (M).
The calculator uses the values as entered and assumes the listed units. Its second result converts mol/L to micromol/L by multiplying by 1,000,000. The example value for ε is illustrative, not a universal constant: absorptivity varies with substance, wavelength, solvent, pH, and other conditions. Use a value from a reliable reference for the exact analyte and method, or determine the relationship with calibration standards.
Worked Example
Using the calculator’s defaults, A = 0.500, ε = 10,000 L/(mol·cm), and l = 1 cm:
c = A / (εl)
c = 0.500 / (10,000 × 1)
c = 0.000050000 mol/L = 5.0000 × 10−5 mol/L
In micromol/L: 5.0000 × 10−5 mol/L × 1,000,000 = 50.00 micromol/L. Rounded to the calculator’s displayed precision, the outputs are 0.000050 mol/L and 50.00 micromol/L.
Assumptions
- The sample is sufficiently dilute for absorbance to be proportional to concentration over the measurement range.
- The sample is measured at the wavelength and under the conditions for which ε applies.
- The path length is the actual optical path through the sample, in cm.
- The measured absorbance has been blank-corrected and is not distorted by scattering, stray light, or interfering substances.
- The analyte’s identity and absorbing chemical form are known; no universal ε is assumed.
How Absorbance Reveals Concentration
A spectrophotometer measures how much light a sample absorbs at a selected wavelength. Absorbance is defined as A = log10(I0/I), where I0 is the incident light intensity and I is the transmitted intensity. Higher absorbance means less light reaches the detector. For a dilute, well-behaved solution, the Beer–Lambert law predicts that absorbance rises in proportion to both concentration and path length.
This proportionality makes the equation useful for solutions of known absorbing compounds. If a cuvette’s path length is doubled while concentration and other conditions stay fixed, absorbance is expected to double within the law’s valid range. Conversely, if absorbance and path length are known and ε is available, concentration can be calculated directly.
The law is not a universal conversion from any absorbance reading to concentration. Absorbance alone is insufficient: different compounds can absorb very differently, and the same compound’s absorptivity changes with wavelength. A reader who has only an absorbance value must also obtain ε or establish a calibration curve using standards of known concentration.
Using the Calculator and Choosing Inputs
- Enter absorbance after blank correction. Absorbance has no physical unit, although instruments may label it AU.
- Enter the molar absorptivity for the analyte at the measurement wavelength, in L/(mol·cm). Confirm the units in the source: a value reported in a different unit system must be converted before use.
- Enter the optical path length in centimetres. A standard 1 cm cuvette is common, but microvolume cells and other measurement formats can have different path lengths.
- Read concentration in mol/L and, for easier comparison at low concentrations, micromol/L.
For instance, a reading of 0.500 does not by itself establish a concentration. With ε = 10,000 L/(mol·cm) and a 1 cm path, it corresponds to 50 micromol/L. If the actual ε were 5,000 with the same absorbance and path, the calculated concentration would instead be 100 micromol/L. The value of ε is therefore a key input, not a minor adjustment.
When ε is unknown or the sample matrix may affect the signal, use a calibration curve: measure absorbance for several standards with known concentrations, plot absorbance against concentration, and determine the relationship over the working range. For a linear fit with intercept, calculate concentration from the fitted line rather than assuming it passes through zero. A blank and appropriate controls help identify background signal.
Common Errors and Limits
- Using the wrong wavelength: ε must correspond to the wavelength used for the sample. A value measured at a different wavelength may produce a misleading result.
- Mixing path-length units: this calculator expects cm. Entering a value in mm without converting it changes the answer by a factor of ten.
- Confusing molar and mass concentration: mol/L is not mg/L. To convert a molar concentration to g/L, multiply by the compound’s molar mass in g/mol; convert g/L to mg/L by multiplying by 1,000.
- Ignoring dilution: if the measured sample was diluted, the result is the concentration in the diluted measurement solution. Multiply by the dilution factor to recover the original concentration, provided the dilution was accurately made.
- Trusting an out-of-range reading: high absorbance can exceed an instrument’s useful range, while very low absorbance may be comparable to noise. Dilute and remeasure when appropriate, then apply the dilution factor, or use a validated method’s stated range.
- Assuming all measured light loss is absorption: suspended particles, bubbles, dirty optical surfaces, and sample background can scatter or block light and inflate apparent absorbance.
Real measurements can depart from ideal linearity because of chemical interactions, changing refractive properties at higher concentrations, detector limitations, or stray light. A calibration curve measured under the same conditions often accounts for practical instrument and matrix effects better than a literature ε. Follow your lab method, the safety data sheet (SDS) and your supervisor.
Frequently Asked Questions
Can I calculate concentration from absorbance alone?
No. You also need the molar absorptivity at the measurement wavelength and the optical path length, or a calibration curve relating absorbance to known concentrations.
What is the concentration formula from absorbance?
Use c = A/(εl), rearranged from A = εlc. With A dimensionless, ε in L/(mol·cm), and l in cm, c is in mol/L.
What if I do not know the molar absorptivity?
Measure standards with known concentrations to build a calibration curve under the same wavelength and sample conditions. Do not substitute an arbitrary ε.
Does absorbance have units?
Absorbance is dimensionless because it is a logarithm of an intensity ratio. It is commonly displayed as AU, but AU is a reporting convention rather than a concentration unit.
How do I account for a diluted sample?
The calculated value is for the solution placed in the measurement cell. Multiply it by the total dilution factor to estimate the original concentration; for example, a tenfold dilution uses a factor of 10.
Can the Beer–Lambert law be used at any absorbance?
No. It works best in a validated linear range for the instrument and sample. At very high or very low readings, measurement limitations and chemical or optical effects can make a direct calculation unreliable.
Related
Formula used
in a | Absorbance | - | 0.500 | 0 in eps | Molar absorptivity | L/(mol·cm) | 10000 | 0.001 in l | Path length | cm | 1 | 0.001 out c | Concentration | mol/L | a / (eps * l) | 6 out cm | Concentration | micromol/L | c * 1000000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Liters to Cubic Meters: Conversion and Examples0.001000 m³
- Normal Cubic Meter to Liters Calculator1,000.00 L
- Qt to Liters Conversion: US and Imperial Quarts0.946353 L
- Meters to Liters Formula: Convert Length to Volume?1,000.000 L
- Meters to Litres: Why Length Alone Is Not Enough1,000.00 L
- Meters Into Liters Calculator: The Missing Dimension