molecalculator

Moles & Molar Mass

Motor RPM from Hz: How to Calculate It

Calculator No. 01-7316 · Updated · Formula and assumptions shown below

Synchronous speed 1,800 RPM
Typical slip (induction motor)
3 %
= 3
Estimated actual speed
1,746 RPM
= Synchronous speed × (1 − Typical slip (induction motor) ÷ 100)
Frequency
60 Hz
Set in the form below
You enter
Frequency (Hz), Number of poles
You get
Synchronous speed (RPM), Typical slip (induction motor) (%), Estimated actual speed (RPM)
Rounding
0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

To calculate motor RPM from Hz, use the formula RPM = (Frequency in Hz × 120) ÷ Number of motor poles. For a standard 4-pole motor running on 60 Hz, this gives 1800 RPM (synchronous speed); on 50 Hz, the same motor gives 1500 RPM. This page explains the formula, the difference between synchronous and actual (slip) speed, and how to apply it to real motors.

Formula

The fundamental equation for synchronous motor speed is:

Ns = (120 × f) / P

  • Ns = synchronous speed in revolutions per minute (RPM)
  • f = supply frequency in hertz (Hz), typically 50 or 60
  • P = number of magnetic poles per phase (always an even number: 2, 4, 6, 8, etc.)

The constant 120 comes from 60 seconds per minute × 2 (because one AC cycle produces two pole passes). For actual speed of an induction motor, subtract slip (typically 2–5%).

Worked Example

Using the calculator defaults: frequency = 60 Hz, poles = 4, slip = 3%.

  1. Synchronous speed = (120 × 60) / 4 = 7200 / 4 = 1800 RPM
  2. Slip speed = 1800 × 0.03 = 54 RPM
  3. Actual speed = 1800 − 54 = 1746 RPM

So a typical 4-pole induction motor on 60 Hz runs at about 1746 RPM under load, not 1800.

Assumptions

  • The motor is AC powered (synchronous or induction).
  • The number of poles is known and fixed (it is determined by the motor’s winding).
  • For induction motors, slip is estimated (typical 2–5%); the calculator uses 3% as default, but real slip depends on load and motor design.
  • Frequency is the supply frequency (mains or VFD output).

Why 120? The Background Behind the Formula

AC motors work by creating a rotating magnetic field. The speed of that field depends on how many times the current alternates per second (Hz) and how many magnetic poles the motor has. One full AC cycle makes the field rotate 360° electrical degrees. For a 2-pole motor, that equals one full mechanical revolution; for a 4-pole motor, it takes two cycles per revolution. The 120 factor merges the 60 seconds per minute with the 2 poles per cycle. That is why the formula is not simply f × something—it is f × 120 / P.

This relationship is fundamental to all AC motors, whether they are tiny fan motors or huge industrial drives. It also explains why the same motor runs slower on 50 Hz than on 60 Hz: a 4-pole motor gives 1500 RPM on 50 Hz versus 1800 RPM on 60 Hz.

Synchronous vs. Actual Speed (Slip)

For a synchronous motor (used in clocks, some high-precision drives), the rotor locks to the rotating field, so actual speed equals synchronous speed exactly. For an induction motor (the most common type), the rotor cannot reach field speed—it must “slip” to induce current. Slip is expressed as a percentage of synchronous speed. Typical values:

  • No load: 0.5–1%
  • Full load: 2–5% (small motors may be 5–10%)

So if you measure the actual RPM with a tachometer, you will see a value slightly below the synchronous speed. The calculator’s “actual speed” output uses a 3% slip default, but for precise work you should use the motor nameplate’s rated slip or measure it.

How to Determine the Number of Poles

You cannot always see the poles directly, but you can find them from the motor nameplate or by the rated speed:

  • Nameplate often lists “4P” or “Poles: 4”.
  • If not, use the rated speed at 60 Hz: 3600 → 2 poles, 1800 → 4 poles, 1200 → 6 poles, 900 → 8 poles.
  • On 50 Hz, the corresponding speeds are 3000, 1500, 1000, 750.

Note that the rated speed on the nameplate is the actual speed (with slip), so a 4-pole motor might say 1740 RPM. That is close to 1800, so you can still identify it as 4-pole.

Using a Variable Frequency Drive (VFD)

When you use a VFD to control motor speed, you change the frequency. For example, a 4-pole motor at 30 Hz runs at 900 RPM synchronous (about 873 RPM actual). The formula works exactly the same. However, VFDs also adjust voltage proportionally to frequency (V/f ratio) to maintain torque. At very low frequencies (below about 10% of rated), the motor may overheat or lose torque unless the VFD is set correctly. Always follow the motor and VFD manufacturer’s guidelines.

Common Mistakes and Misconceptions

  • Confusing synchronous with actual speed: The formula gives synchronous speed; real induction motors are slower by slip. If you need actual RPM, subtract slip.
  • Using the wrong pole count: Poles are always even. A “4-pole” motor has 4 poles, not 4 pole pairs. Some people mistakenly use 2 for a 4-pole motor, which doubles the speed.
  • Forgetting to convert units: Frequency must be in Hz, not RPM. The formula already includes the conversion from cycles per second to revolutions per minute.
  • Assuming 60 Hz everywhere: Many countries use 50 Hz. Always check the supply frequency or VFD setting.
  • Ignoring load: Slip increases with load. A motor under heavy load may have 5% slip, not 3%.

Frequently Asked Questions

How many RPM is 60 Hz on a 4-pole motor?

Synchronous speed is 1800 RPM. Actual speed is typically 1740–1770 RPM depending on load. The nameplate often lists the actual speed, e.g., 1750 RPM.

What is the formula for RPM from Hz?

RPM = (120 × Hz) / number of poles. For example, 50 Hz with 6 poles: (120 × 50) / 6 = 1000 RPM synchronous.

How do I find the number of poles from RPM?

Divide 120 by the frequency, then divide by the synchronous RPM. For instance, at 60 Hz, 1800 RPM → 120/60 = 2, then 2/1800? Actually, use: Poles = (120 × Hz) / RPM. So for 60 Hz and 1800 RPM, poles = 7200/1800 = 4.

Does a VFD change the number of poles?

No, the poles are fixed by the motor’s winding. A VFD changes the frequency, which changes the synchronous speed, but the pole count remains the same.

Why is my motor’s actual RPM lower than calculated?

Because of slip. The rotor of an induction motor must lag behind the rotating field to induce current. The difference is usually 2–5% of synchronous speed. If the motor is overloaded, slip increases further.

Can I use this formula for DC motors?

No. DC motor speed is controlled by voltage, not frequency. The formula applies only to AC synchronous and induction motors.

Practical Tips for Using the Calculator

  • Enter the exact frequency from your mains (e.g., 60 in the US, 50 in Europe) or the VFD setting.
  • Determine poles from the nameplate or rated speed.
  • Adjust slip if you know the motor’s full-load slip from the nameplate (e.g., 4%).
  • For synchronous motors, set slip to 0%.
  • Remember that the result is an estimate; actual speed can vary with load, temperature, and voltage.

This calculator gives the theoretical synchronous speed and an estimated actual speed for typical induction motors. For precise speed measurement, use a tachometer or encoder. Always follow the motor manufacturer’s data and your local electrical safety standards when working with live equipment.

Related

Formula used
in f | Frequency | Hz | 60 | 0
in p | Number of poles | - | 4 | 2
out sync | Synchronous speed | RPM | f * 120 / p | 0
out slip | Typical slip (induction motor) | % | 3 | 0
out actual | Estimated actual speed | RPM | sync * (1 - slip / 100) | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →