molecalculator

Moles & Molar Mass

Heat Exchanger U-Value Calculator and Formula

Calculator No. 01-2165 · Updated · Formula and assumptions shown below

Overall heat-transfer coefficient U 250.00 W/(m²·K)
Heat-transfer rate
10000 W
Set in the form below
Heat-transfer area
2 m²
Set in the form below
Log mean temperature difference
20 K
Set in the form below
You enter
Heat-transfer rate (W), Heat-transfer area (m²), Log mean temperature difference (K)
You get
Overall heat-transfer coefficient U (W/(m²·K))
Rounding
2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Calculate a heat exchanger’s overall heat-transfer coefficient, U, by dividing the heat-transfer rate by the area and the temperature difference that drives the transfer. Enter heat duty in watts, heat-transfer area in square metres, and the log mean temperature difference in kelvins; the calculator returns U in W/(m²·K).

Formula

The overall heat-transfer coefficient is the heat-transfer rate divided by the area multiplied by the log mean temperature difference:

U = Q / (A × ΔTlm)

  • U is the overall heat-transfer coefficient, in watts per square metre kelvin, W/(m²·K).
  • Q is the heat-transfer rate, or duty, in watts (W).
  • A is the heat-transfer area in square metres (m²), using the area basis appropriate to the U-value being reported.
  • ΔTlm is the log mean temperature difference (LMTD) in kelvins (K). For a heat exchanger that needs a correction factor, use corrected LMTD in the calculation.

When temperatures are supplied in degrees Celsius, temperature differences have the same numerical size in kelvins: a 20 °C difference equals 20 K. Do not convert a temperature difference by adding 273.15. The calculator assumes that the entered duty, area and temperature difference are positive and refer to the same operating condition.

Worked Example

Using the calculator defaults—Q = 10,000 W, A = 2 m², and ΔTlm = 20 K—calculate the area-temperature product first:

A × ΔTlm = 2 m² × 20 K = 40 m²·K

Then divide the duty by that product:

U = 10,000 W / 40 m²·K = 250 W/(m²·K)

The calculator displays 250.00 W/(m²·K). This is an illustrative calculation, not a design recommendation; actual exchanger performance depends on its fluids, geometry, flow conditions and fouling.

Assumptions

  • Heat duty is the rate of heat transferred under the operating condition of interest, not a total energy quantity.
  • The area is the area used as the reference for U, such as outside tube area or inside tube area, and is consistent with any comparison value.
  • The temperature difference is the appropriate LMTD, including a correction factor when the exchanger arrangement requires one.
  • The calculation provides an overall, averaged coefficient; it does not resolve local temperature or flow variations.

What the U-Value Means

U describes the combined ability of the exchanger’s materials and fluids to transfer heat per unit area for each kelvin of temperature difference. A higher U means more heat can pass through a given area at a given temperature driving force. It does not, by itself, tell you how much heat the exchanger will transfer: that also depends on available area and temperature difference.

The overall value combines multiple thermal resistances. These commonly include convection between each fluid and a separating surface, conduction through the exchanger wall, and additional resistance from deposits or fouling. In simplified form, resistances are added in series. For a flat wall with a consistent area basis, an illustrative relationship is:

1/U = 1/hhot + Rf,hot + t/k + Rf,cold + 1/hcold

Here, h values are convection coefficients in W/(m²·K), Rf values are fouling resistances in m²·K/W, t is wall thickness in metres, and k is wall thermal conductivity in W/(m·K). Real exchanger calculations may need cylindrical-wall equations and consistent inside or outside area conversions; this flat-wall expression is a guide to the resistance concept, not a universal design equation.

How to Calculate the LMTD

For a counter-current exchanger, find the temperature difference at each end, ΔT1 and ΔT2, pairing the hot and cold streams at the corresponding ends. Then calculate:

ΔTlm = (ΔT1 − ΔT2) / ln(ΔT1/ΔT2)

The same logarithmic-mean form applies to parallel flow when the end differences are paired consistently. Both end differences must be positive for this simple expression. Multipass and crossflow arrangements may require an LMTD correction factor, commonly represented as F; use ΔTcorrected = F × ΔTlm when that method is applicable. A wrong flow arrangement or omitted correction can make a calculated U misleading.

Alternatively, estimate duty from a stream’s mass flow and heat capacity when suitable data are available: Q = ṁ × cp × ΔT for a single-phase stream with approximately constant heat capacity. Here ṁ is mass flow in kg/s, cp is specific heat in J/(kg·K), and ΔT is that stream’s temperature change in K. For phase change, variable properties, heat loss or multiple streams, use an appropriate energy balance rather than assuming this simple form applies.

Area Basis, Units, and Comparisons

Always state the surface area basis alongside U. A tubular exchanger can have different inside and outside surface areas, so a U-value calculated on one basis will not numerically match one calculated on the other. The underlying heat duty is the same, but the coefficient changes with the area used in Q = UAΔTlm.

Use watts for Q, square metres for A and kelvins for the temperature difference to obtain W/(m²·K). If duty is in kilowatts, multiply by 1,000 to convert to watts; if area is in square feet, convert it to square metres before using this calculator. Keeping units consistent prevents errors that can change a result by large factors.

U-values are not universal constants for a type of exchanger. They vary with fluid properties, flow velocity, phase change, geometry, surface condition and operating state. A value from a reference table is useful only when its service, area convention, units and fouling assumptions are comparable. Use project-specific data or a validated design method when selecting equipment.

Interpreting Results and Common Errors

A calculated U can be useful for checking measured performance or estimating required area. Rearranging the equation gives A = Q/(UΔTlm): if the required duty or temperature difference rises while U stays fixed, more area is needed. This is a preliminary relationship, not a substitute for checking pressure drop, flow distribution, mechanical limits or operating margins.

  • Confusing power with energy: Q in this equation is a rate, such as W or kW. A total quantity in joules must first be divided by the time over which it was transferred.
  • Using the wrong temperature difference: Do not automatically use the inlet-to-inlet difference or an arithmetic average; calculate the appropriate LMTD and any required correction.
  • Mixing area bases: Label U as inside-area-based or outside-area-based when relevant.
  • Ignoring fouling or changes in operation: Deposits and altered flow can reduce effective performance, so a clean design value may not represent an exchanger in service.
  • Overinterpreting precision: A result with many decimal places does not make uncertain measurements exact. Report precision appropriate to the input data.

To compare a calculated U with a reference or design value, check that both use the same units, area convention, exchanger configuration, operating conditions and treatment of fouling. A discrepancy can indicate measurement uncertainty, an incorrect duty or LMTD, or a real performance change; U alone does not identify the cause.

Frequently Asked Questions

What is a typical U-value for a heat exchanger?
There is no single typical value that applies to every exchanger. U depends on the fluids, whether either stream changes phase, flow and surface conditions, exchanger construction, area basis and fouling. Compare values only when those conditions and conventions are similar.

Can I calculate U from inlet and outlet temperatures alone?
Not generally. You also need the heat-transfer rate and exchanger area. Temperatures help determine the LMTD and may help establish duty if flow rates and appropriate heat capacities or phase-change data are known.

Is U the same as the heat-transfer coefficient h?
No. A fluid-side convection coefficient h describes heat transfer between one fluid and a surface. Overall U includes the relevant resistances on both sides, through the wall, and from fouling where included.

Should LMTD be in Celsius or kelvins?
Either gives the same numerical value for a temperature difference: 1 °C of difference equals 1 K. Use temperature differences, not absolute temperatures, in the LMTD formula.

Why does my calculated U seem too high or too low?
Check the heat-duty units, area basis, end-temperature pairing, flow arrangement and any required LMTD correction factor. Also confirm that the measurements describe the same steady operating condition and that total energy was not entered as a heat-transfer rate.

Related

Formula used
in q | Heat-transfer rate | W | 10000 | 0
in a | Heat-transfer area | m² | 2 | 0.000001
in dt | Log mean temperature difference | K | 20 | 0.000001
out u | Overall heat-transfer coefficient U | W/(m²·K) | q / (a * dt) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →