molecalculator

Moles & Molar Mass

Mole Volume Calculator: Find Gas Volume at STP

Calculator No. 01-1204 · Updated · Formula and assumptions shown below

Gas volume 22.4140 L
Volume per mole
22.4140 L/mol
= 8.31446261815324 × (Temperature + 273.15) ÷ Pressure
Amount of gas
1 mol
Set in the form below
Temperature
0 °C
Set in the form below
You enter
Amount of gas (mol), Temperature (°C), Pressure (kPa)
You get
Gas volume (L), Volume per mole (L/mol)
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Use this calculator to find the volume occupied by a specified amount of gas, entering the amount in moles and the temperature and pressure. It returns the gas volume in liters using the ideal gas law; a mole by itself does not have one fixed volume because volume depends on the substance and conditions.

Formula

The ideal gas law is PV = nRT. Rearranging gives V = nRT/P, the formula used here. In this calculator, temperature is entered in degrees Celsius and converted to kelvin by adding 273.15; the gas constant is R = 8.31446261815324 J/(mol·K). Because 1 J equals 1 kPa·L, the input pressure in kPa makes the resulting volume come out in liters.

  • V is gas volume, in liters (L).
  • n is amount of gas, in moles (mol).
  • T is absolute temperature, in kelvin (K), calculated as entered °C + 273.15.
  • P is absolute pressure, in kilopascals (kPa).
  • R is the ideal gas constant, 8.31446261815324 J/(mol·K).

The second output, molar volume, is V/n = RT/P, in liters per mole. It is the volume one mole would occupy at the entered temperature and pressure under the ideal-gas assumption. It is not a second independent measurement.

Worked Example

With the defaults, the calculator uses 1 mol of gas at 0 °C and 101.325 kPa. First convert Celsius to kelvin:

T = 0 + 273.15 = 273.15 K

Then apply the ideal gas law, with pressure in kPa:

V = (1 mol × 8.31446261815324 J/(mol·K) × 273.15 K) / 101.325 kPa

V ≈ 22.41397 L, which the calculator displays to four decimal places as 22.4140 L. The corresponding molar volume is also 22.4140 L/mol. This is the familiar ideal-gas molar volume at 0 °C and 1 atmosphere, where 1 atm = 101.325 kPa.

Assumptions

  • The gas behaves ideally, so particles’ own volume and intermolecular attractions are treated as negligible.
  • Temperature is uniform and pressure is absolute, not gauge pressure.
  • The entered amount is gas in the same volume and state described by the entered temperature and pressure.

Why a Mole Has No Single Volume

A mole is a counting unit for amount of substance, not a unit of size. One mole contains exactly 6.02214076 × 1023 specified entities—such as molecules, atoms, or ions. The amount alone says how many entities there are, but not how much space they take up.

For a gas, the space occupied depends strongly on pressure and temperature. Raising the temperature at fixed pressure increases ideal-gas volume; raising pressure at fixed temperature decreases it. The identity of a real gas also matters, especially at high pressure or low temperature, where intermolecular forces and the finite size of molecules make the ideal-gas approximation less accurate.

For liquids and solids, molar volume depends primarily on the substance and its density, as well as temperature and pressure. A useful relation is molar volume = molar mass / density. Therefore, there is no universal “volume of a mole” that applies to gases, liquids, and solids alike.

How to Use the Calculator

  • Enter the amount of gas in moles. For a sample with a known particle count, convert entities to moles by dividing by 6.02214076 × 1023.
  • Enter the gas temperature in °C. The conversion to kelvin is performed in the formula; do not enter a kelvin value in this field.
  • Enter the absolute pressure in kPa. Convert other units before entering them: 1 atm = 101.325 kPa, and 1 bar = 100 kPa.
  • Read the first result as total volume in liters and the second as volume per mole in L/mol.

Pressure must be absolute. A gauge-pressure reading is measured relative to the surrounding atmosphere, so it must be converted by adding atmospheric pressure when appropriate. For example, a gauge value of 0 kPa does not mean zero absolute pressure; it usually means pressure is approximately atmospheric. Use the pressure relevant to the gas sample, not a gauge value copied without conversion.

Standard Conditions and Real-Gas Limits

The phrase “standard temperature and pressure” is used with more than one convention, so it is important to state the actual values. At 0 °C and 101.325 kPa, the ideal molar volume is about 22.414 L/mol. At 0 °C and 100 kPa, it is about 22.711 L/mol. At 25 °C and 100 kPa, it is about 24.790 L/mol. These are calculated values under the ideal-gas law, not one universal constant for every stated standard.

Many ordinary gases near atmospheric pressure are close enough to ideal for classroom calculations. The approximation can become poor near a gas’s condensation point or at high pressures. In those cases, a compressibility factor or a more detailed equation of state may be needed; this calculator does not apply those corrections. Treat results as estimates when non-ideal behavior is significant.

Common Mistakes

  • Assuming every mole occupies 22.4 L: that familiar figure applies approximately to an ideal gas at 0 °C and 1 atm, not to all temperatures, pressures, or phases.
  • Mixing pressure units: the calculator expects kPa. Entering a value in atmospheres or pascals without conversion can change the result greatly.
  • Using Celsius directly in the gas law: the formula requires kelvin, so the conversion +273.15 is essential.
  • Confusing amount with mass: grams are not moles. Convert mass to amount using the substance’s molar mass before using this calculator.
  • Using gauge instead of absolute pressure: the ideal gas law uses absolute pressure measured from a vacuum.

For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor. This calculator is for general study and lab-planning arithmetic, not a substitute for a procedure or measurement.

Frequently Asked Questions

How much volume is one mole of gas?
There is no single value without temperature and pressure. For an ideal gas at 0 °C and 101.325 kPa, one mole occupies about 22.414 L.

Does one mole always equal 22.4 liters?
No. That is an approximate molar volume for an ideal gas under a specific set of conditions. Changing temperature or pressure changes the volume, and real gases can differ from the ideal prediction.

What is the volume of one mole at room temperature?
It depends on what temperature and pressure are meant by “room temperature.” At 25 °C and 100 kPa, the ideal-gas value is about 24.790 L/mol; at other conditions, calculate it with V = nRT/P.

How do I find the volume of a mole of liquid?
Use the liquid’s molar mass and density at the relevant conditions: molar volume = molar mass ÷ density. The gas-law calculator above is not suitable for liquids or solids.

How many molecules are in a mole?
One mole contains exactly 6.02214076 × 1023 specified entities. For a molecular substance, those entities are molecules; for an atomic substance, they may be atoms.

Related

Formula used
in n | Amount of gas | mol | 1 | 0
in t | Temperature | °C | 0 | -273.15
in p | Pressure | kPa | 101.325 | 0.001
out v | Gas volume | L | n * 8.31446261815324 * (t + 273.15) / p | 4
out vm | Volume per mole | L/mol | 8.31446261815324 * (t + 273.15) / p | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →