The change of enthalpy (ΔH) is calculated using the formula ΔH = qp, where qp is the heat absorbed or released by a system at constant pressure. In most chemistry problems, you’ll use the expanded form ΔH = m·c·ΔT (for a temperature change in a substance) or ΔH = ΣΔHf(products) − ΣΔHf(reactants) (for a chemical reaction). This page explains each version, when to use it, and how to avoid common mistakes.
Formula
The most direct definition: ΔH = qp, where ΔH is the enthalpy change and qp is heat transferred at constant pressure. Enthalpy (H) is a state function: H = U + PV, where U is internal energy, P is pressure, and V is volume. At constant pressure, the change in enthalpy equals the heat exchanged with the surroundings.
For a temperature change in a single substance, the formula is:
ΔH = m × c × ΔT
- m = mass of the substance (grams, g)
- c = specific heat capacity (J/(g·°C) or J/(g·K))
- ΔT = Tfinal − Tinitial (°C or K, same difference)
For a chemical reaction at constant pressure, use standard enthalpies of formation (ΔHf°):
ΔHrxn° = Σ ΔHf°(products) − Σ ΔHf°(reactants)
Each term is multiplied by its stoichiometric coefficient. The unit is typically kJ/mol of reaction as written.
Worked Example
Using the calculator defaults: heat 100 g of water (c = 4.184 J/(g·°C)) from 20 °C to 30 °C.
- Calculate ΔT: 30 − 20 = 10 °C
- Apply ΔH = m × c × ΔT = 100 × 4.184 × 10
- ΔH = 4184 J
- Convert to kJ: 4184 / 1000 = 4.184 kJ
The calculator shows 4184.00 J and 4.1840 kJ. Positive ΔH means heat is absorbed (endothermic).
Assumptions
- Pressure is constant (open container, atmospheric pressure).
- No phase change occurs during the temperature range.
- Specific heat capacity is constant over the temperature interval.
- No heat loss to the surroundings (ideal calorimetry).
- For reaction enthalpies, all substances are in their standard states at 25 °C and 1 bar.
When to Use Each Form
Choose the formula based on what you know:
- Temperature change of a substance – use ΔH = m·c·ΔT. This works for heating water, cooling a metal, or mixing solutions.
- Chemical reaction at constant pressure – use ΔHrxn° = ΣΔHf°(products) − ΣΔHf°(reactants). This is for reactions where bonds break and form.
- Phase change (melting, boiling) – use ΔH = n × ΔHfus or ΔH = n × ΔHvap, where n is moles and ΔHfus/ΔHvap are molar enthalpies of fusion/vaporization.
- Bond energies – ΔH ≈ Σ(bonds broken) − Σ(bonds formed), using average bond dissociation energies. This is an estimate, not exact.
How to Read the Result
The sign of ΔH tells you the direction of heat flow:
- ΔH > 0 (positive) – endothermic process; the system absorbs heat from the surroundings. Example: melting ice.
- ΔH < 0 (negative) – exothermic process; the system releases heat to the surroundings. Example: combustion of methane.
For a reaction, ΔH is usually reported per mole of reaction as written. If you double the coefficients, ΔH doubles. If you reverse the reaction, the sign of ΔH flips.
Common Mistakes and Misconceptions
- Confusing ΔH with ΔU – ΔH = ΔU + Δ(PV). For reactions involving gases, ΔH and ΔU differ by the work done (ΔngasRT). At constant volume, q = ΔU, not ΔH.
- Using °C vs K incorrectly – For ΔT, the numerical difference is identical in °C and K, so you can mix them. But for absolute temperatures in the ideal gas law, you must use Kelvin.
- Forgetting units – Specific heat can be J/(g·°C) or J/(kg·K). Convert mass to match the unit. 1 J/(g·°C) = 1000 J/(kg·K).
- Sign errors – When using ΔHf°, always subtract reactants from products. A common error is subtracting products from reactants.
- Assuming ΔH is independent of temperature – In reality, ΔH changes with temperature (Kirchhoff’s law), but for small ranges, it’s often neglected.
Limits of the Formula
The simple ΔH = m·c·ΔT assumes no phase change and constant c. It fails for:
- Substances with temperature-dependent specific heat (e.g., gases over large ranges).
- Processes with phase changes – you must add the latent heat term.
- Very high pressures where PV work is significant.
The formation-enthalpy method works only for reactions at standard state; for non-standard conditions, you need heat capacity corrections. Also, ΔHf° values are averages from calorimetry, so they carry experimental uncertainty.
Frequently Asked Questions
What is the difference between ΔH and q?
At constant pressure, ΔH equals q (heat). At constant volume, q equals ΔU (change in internal energy). For most bench chemistry in open flasks, pressure is constant, so ΔH ≈ q. For reactions in a bomb calorimeter (constant volume), you measure ΔU and then convert to ΔH using ΔH = ΔU + ΔngasRT.
Can I use ΔH = m·c·ΔT for a chemical reaction?
Only if the reaction simply changes temperature without a phase change and you know the mass and specific heat of the entire system. For a reaction where bonds break, you need formation enthalpies or bond energies, not just temperature change.
Why is ΔH negative for exothermic reactions?
Because the system loses heat to the surroundings. By convention, heat leaving the system is negative. The surroundings gain that heat, so their ΔH is positive.
How do I find ΔHf° values?
They are tabulated in chemistry textbooks and databases (like NIST). The standard enthalpy of formation of an element in its most stable form (e.g., O2 gas) is defined as zero. For compounds, values are measured via calorimetry.
What is the unit of ΔH?
For a substance, ΔH is in joules (J) or kilojoules (kJ). For a reaction, it’s usually kJ/mol of reaction. For phase changes, it’s kJ/mol of substance. Always check the context.
Does ΔH depend on the path taken?
No. Enthalpy is a state function, so ΔH depends only on the initial and final states, not on how you get there. This is why you can add reaction enthalpies (Hess’s law) to find ΔH for a multi-step process.
Follow your lab method, the safety data sheet (SDS) and your supervisor when performing any calorimetry or reaction work.
Related
Formula used
in m | Mass of substance | g | 100 | 0 in c | Specific heat capacity | J/(g·°C) | 4.184 | 0 in t1 | Initial temperature | °C | 20 | -273.15 in t2 | Final temperature | °C | 30 | -273.15 out dh | Change of enthalpy (ΔH) | J | m * c * (t2 - t1) | 2 out dhkj | Change of enthalpy | kJ | dh / 1000 | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check