A coefficient of linear expansion calculator finds a material’s linear expansion coefficient, α, from its original length, temperature change, and change in length. Enter those three measurements in consistent units to get α, usually expressed in inverse degrees Celsius (°C⁻¹) or inverse kelvins (K⁻¹).
Formula
The calculator uses the standard linear expansion relationship rearranged to solve for the coefficient:
α = ΔL / (L₀ × ΔT)
- α is the average coefficient of linear expansion over the measured temperature interval, in °C⁻¹. A temperature interval of 1 °C has the same size as an interval of 1 K, so its numerical value is also the same in K⁻¹.
- ΔL is the change in length, in metres. It is final length minus initial length; positive means the sample lengthened.
- L₀ is the original length at the starting temperature, in metres.
- ΔT is the temperature change, in °C or K, calculated as final temperature minus initial temperature.
The second output converts the result to parts per million per degree Celsius: 1 ppm/°C = 10⁻⁶ °C⁻¹. The expression multiplies α by 1,000,000 to make that conversion.
Worked Example
Using exactly the default values in the calculator, a 1 m sample increases in length by 0.0012 m while its temperature rises by 100 °C.
First calculate the length-temperature product: L₀ × ΔT = 1 m × 100 °C = 100 m·°C.
Then divide the length change by that product: α = 0.0012 m / 100 m·°C = 0.000012 °C⁻¹. The metres cancel, leaving inverse degrees Celsius.
In parts per million per degree Celsius, 0.000012 × 1,000,000 = 12.00 ppm/°C. Therefore, the calculator’s headline result is 0.00001200 °C⁻¹, followed by 12.00 ppm/°C.
Assumptions
- The sample expands or contracts uniformly along the measured direction.
- The stated change in length is attributable to the temperature change, rather than stretching, measurement drift, a phase change, or another cause.
- The result is an average coefficient over the temperature interval. It is treated as constant for this calculation.
- Length inputs use the same unit. The calculator specifies metres for both lengths; convert other units before entering them.
What the Coefficient Means
The coefficient describes how much a material’s length changes relative to its original length for each degree of temperature change. For a small temperature interval and a roughly constant α, the expected change is ΔL ≈ αL₀ΔT. A higher coefficient means a greater fractional length change for the same temperature change.
For example, a coefficient of 12 ppm/°C means a one-metre length changes by about 12 micrometres for a 1 °C temperature increase, under the usual linear-expansion approximation. For a 100 °C rise, that estimate becomes 1,200 micrometres, or 0.0012 m. The worked example uses exactly that relationship in reverse to infer the coefficient.
This quantity is often called the linear expansion coefficient or linear thermal expansion coefficient. It is not the same as area or volume expansion. For an isotropic solid—a material whose properties are the same in every direction—and a small temperature change, area expansion is approximately twice linear expansion, while volume expansion is approximately three times linear expansion. Those approximations do not necessarily apply to anisotropic materials, composites, or large temperature ranges.
How to Use the Calculator
- Measure the sample’s original length at the starting temperature and enter it in metres.
- Find the length change, final length minus original length, and enter that difference in metres. Do not enter the final length alone.
- Enter the temperature change as final temperature minus initial temperature. A difference in °C has the same numerical size as the corresponding difference in K.
- Read α in °C⁻¹ and, if useful, its equivalent in ppm/°C. Compare values only when the measurement conditions and coefficient convention are understood.
For example, if measurements are in millimetres, convert both lengths by dividing by 1,000 before entering them. The ratio can be calculated with another consistent length unit mathematically, but following the calculator’s metre labels avoids confusion and helps keep the reported units clear.
Choosing Measurements and Interpreting Results
Accurate inputs matter because the length change may be tiny compared with the original length. Use instruments and methods suitable for the expected expansion, and record the starting and ending temperatures near the sample. Thermal gradients can cause different parts of a specimen to be at different temperatures, while loose supports or applied loads can alter its measured length.
Report the temperature interval and material condition alongside a measured coefficient when precision matters. Many materials do not have one perfectly fixed coefficient: α can vary with temperature, composition, heat treatment, crystal direction, moisture content, and phase. A result measured over a broad interval is therefore an average, not necessarily the value at every temperature within that interval.
A calculated coefficient may be compared with reference data, but only if the reference uses a compatible material, temperature range, and definition (instantaneous or average). Published values are not universal constants. For design decisions involving thermal clearances, stresses, or precision equipment, use validated material data and account for tolerances and operating conditions.
Common Errors and Limits
- Entering final length instead of ΔL: subtract initial length from final length first. The formula uses the change, not the full expanded length.
- Mixing units: converting one length but not the other can produce a result off by a factor of 1,000 or more. Keep L₀ and ΔL in the same unit.
- Using absolute temperatures as ΔT: subtract the two temperatures. For instance, a change from 20 °C to 80 °C is 60 °C, not 80 °C.
- Confusing °C and K: absolute temperatures differ by 273.15, but temperature differences in °C and K are numerically equal. Do not add 273.15 to a temperature difference.
- Rounding too early: preserve the measured digits through the calculation, then round the reported coefficient to a precision justified by the measurements.
The calculator rejects zero temperature change because dividing by zero is undefined. A negative temperature change can also be physically meaningful for cooling, but this calculator’s input limit requires a positive interval. To use cooling data, reverse the comparison so that both ΔL and ΔT are expressed consistently, or use the formula directly with signed changes. An unexpected negative coefficient can occur in some materials and directions, but it cannot be entered through this calculator’s nonnegative change fields.
Frequently Asked Questions
What is the formula for the coefficient of linear expansion?
For an average coefficient over a temperature interval, α = ΔL/(L₀ΔT), where ΔL is the length change, L₀ is the original length, and ΔT is the temperature change.
What units are used for linear expansion coefficient?
Common units are °C⁻¹ and K⁻¹; these have the same numerical value when describing temperature intervals. Parts per million per degree Celsius (ppm/°C) are also common: 1 ppm/°C equals 10⁻⁶ °C⁻¹.
Can I calculate linear expansion from final length?
Yes, first find ΔL = final length − initial length. Then use that difference in the formula. Entering the final length in the change field gives an incorrect result.
Is the coefficient of linear expansion constant?
Not always. It can vary with temperature and material structure. A calculation from measurements across an interval gives an average coefficient for those conditions.
Is linear expansion the same as volumetric expansion?
No. Linear expansion describes change along one dimension. For isotropic solids over small temperature changes, volume expansion is approximately three times linear expansion, but the relationship may not hold for anisotropic materials or broader conditions.
Related
Formula used
in l0 | Original length | m | 1 | 0 in dl | Change in length | m | 0.0012 | 0 in dt | Temperature change | °C | 100 | 0.000001 out alpha | Coefficient of linear expansion | 1/°C | dl / (l0 * dt) | 8 out ppm | Coefficient in parts per million per °C | ppm/°C | alpha * 1000000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Gas Correction Factor Formula and Calculator0.9829
- Gas Correction Factor Calculator and Table1.2534
- Gas Temperature: Calculate It from Pressure and Volume298.15 K
- Gas Correction Factor Calculator: Formula and Uses107.322 same as input
- Density Temperature Correction Calculator and Formula999.25 kg/m^3
- Gas Cv Calculator: Heat Capacity Ratio and Formula20.786 J/(mol·K)