molecalculator

Moles & Molar Mass

Concentrated Sulfuric Acid Molar Mass and Calculator

Calculator No. 01-2838 · Updated · Formula and assumptions shown below

Moles of H₂SO₄ 0.9993 mol
Mass of H₂SO₄
98.000 g
= Mass of solution × Sulfuric acid mass fraction ÷ 100
Mass of solution
100 g
Set in the form below
Sulfuric acid mass fraction
98 %
Set in the form below
You enter
Mass of solution (g), Sulfuric acid mass fraction (%), Molar mass of H₂SO₄ (g/mol)
You get
Moles of H₂SO₄ (mol), Mass of H₂SO₄ (g)
Rounding
4 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Pure sulfuric acid (H₂SO₄) has a molar mass of 98.072 g/mol, usually reported as 98.08 g/mol. This calculator uses the molar mass and the stated mass fraction of a sulfuric acid solution to estimate the moles of H₂SO₄ in a sample; enter the solution mass, its concentration by mass, and the molar mass to get moles and acid mass.

Formula

The formula for the number of moles is n = (m × w / 100) / M. Here, n is the amount of sulfuric acid in moles (mol), m is the mass of the whole solution in grams (g), w is the acid concentration as a mass percentage (%), and M is the molar mass of pure H₂SO₄ in grams per mole (g/mol). The calculator first finds the mass of acid, macid = m × w / 100, then divides by the molar mass.

The molar mass value follows from the formula’s atoms and standard atomic weights: H₂SO₄ contains two hydrogen atoms, one sulfur atom, and four oxygen atoms. Using H = 1.008, S = 32.06, and O = 15.999 g/mol gives 2(1.008) + 32.06 + 4(15.999) = 98.072 g/mol. The mass percentage must be entered as a percentage number, such as 98, not as a decimal fraction such as 0.98.

Worked Example

Using the defaults, the sample is 100 g of solution at 98% by mass, and the molar mass is 98.072 g/mol.

  1. Find the sulfuric acid mass: 100 g × 98 / 100 = 98 g H₂SO₄.
  2. Divide that acid mass by the molar mass: 98 g / 98.072 g/mol = 0.99927 mol.

The calculator reports 0.9993 mol to four decimal places, plus an acid mass of 98.000 g to three decimal places. The remaining 2 g in this example represents the solution’s other components, treated as non-sulfuric-acid mass for this calculation.

Assumptions

  • The entered mass percentage describes the mass of H₂SO₄ divided by the total solution mass.
  • The molar mass is for pure molecular H₂SO₄, not for the whole solution.
  • The calculation concerns amount of substance only; it does not infer volume, density, temperature, or reaction yield.

Why Concentrated Acid Still Has the Same Molar Mass

“Concentrated” describes a solution containing a high proportion of sulfuric acid; it does not change the molar mass of an H₂SO₄ molecule. A molecule’s molar mass depends on its chemical formula and the atomic masses used, not on how much water is mixed with it. Thus pure H₂SO₄ and H₂SO₄ present in a concentrated aqueous solution share the same molecular molar mass, about 98.072 g/mol.

What changes with concentration is how many moles of H₂SO₄ are present in a given mass or volume of solution. Commercial concentrated sulfuric acid is commonly specified near 98% by mass, but that figure is a product specification, not a universal definition of “concentrated.” Check the label or certificate for the actual concentration. A result based on 98% is only an estimate if the sample’s true concentration differs.

Do not confuse molar mass with density or molarity. Molar mass has units of g/mol; density is mass per volume, such as g/mL; molarity is moles of solute per litre of final solution (mol/L). To calculate molarity, you need the solution’s volume or a suitable density and temperature-specific data. This calculator deliberately uses mass fraction and sample mass, so it does not need a volume or density.

How to Use the Result

Use the result when a calculation needs moles of sulfuric acid from a known mass of solution and a stated mass percentage. For instance, the calculator’s default sample contains almost one mole of H₂SO₄. That makes the output useful for study problems and for checking the acid amount specified in a lab calculation, but it does not establish the volume of the sample or the amount of any reaction product.

  • Mass of solution: enter the mass of the entire acid solution, not just its acid component.
  • Mass fraction: enter the concentration in percent by mass. For example, 98% means 98 g acid per 100 g solution.
  • Molar mass: leave the default for H₂SO₄ unless a calculation explicitly uses a different convention or precision.

The formula assumes the concentration is a mass percentage. If a label gives a different basis, such as molarity or a volume percentage, do not enter that number as though it were mass percent. Convert using suitable, condition-specific information or use a calculation designed for that concentration basis. Rounding the molar mass to 98.08 g/mol is usually adequate for classroom arithmetic; retain more digits when the problem calls for them, but avoid implying that the sample concentration is known more precisely than its specification.

Common Mistakes and Limits

A frequent error is using 98 as the molar mass because the acid is “98%.” These numbers describe different things: 98% is a mass fraction specification, while about 98.072 g/mol is the molar mass. Another common error is dividing the mass of the full solution directly by 98.072 g/mol. That would incorrectly treat every gram of solution—including water—as sulfuric acid. Apply the mass percentage first.

This calculator does not convert the result into volume, calculate solution molarity, or account for a concentration that changes with storage or contamination. Those tasks need additional information, and volume calculations in particular can depend on density and temperature. It also does not calculate dissociation or chemical reaction stoichiometry. The reported moles refer to the H₂SO₄ amount represented by the entered mass percentage.

Safety and Handling Context

Concentrated sulfuric acid is highly corrosive and can cause severe chemical burns; dilution releases substantial heat, and contact with water can cause dangerous splashing. This page provides arithmetic, not handling or dilution instructions. For any bench work, follow your lab method, the safety data sheet (SDS), and your supervisor. Use the concentration and handling information supplied for the specific material rather than assuming every concentrated solution has identical properties.

Frequently Asked Questions

What is the molar mass of sulfuric acid?
Pure H₂SO₄ has a molar mass of 98.072 g/mol from the stated atomic weights, commonly rounded to 98.08 g/mol.

Does 98% sulfuric acid have a molar mass of 98 g/mol?
No. The 98% describes the mass fraction of acid in the solution. The molar mass of H₂SO₄ remains about 98.072 g/mol.

How many moles are in 100 g of 98% sulfuric acid?
There are 98 g of H₂SO₄ in that solution mass. Dividing by 98.072 g/mol gives approximately 0.9993 mol.

Is molar mass the same as molarity?
No. Molar mass is measured in g/mol and relates mass to amount of substance. Molarity is measured in mol/L and describes moles per volume of solution.

Can I calculate the volume of concentrated sulfuric acid from this?
Not from molar mass alone. You also need an applicable density and concentration, with temperature taken into account where relevant; the calculator reports mass and moles only.

Related

Formula used
in m | Mass of solution | g | 100 | 0
in w | Sulfuric acid mass fraction | % | 98 | 0 | 100
in mm | Molar mass of H₂SO₄ | g/mol | 98.072 | 0.001
out n | Moles of H₂SO₄ | mol | (m * w / 100) / mm | 4
out a | Mass of H₂SO₄ | g | m * w / 100 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →