molecalculator

Moles & Molar Mass

Cv to GPM Calculator: Convert Valve Flow Capacity

Calculator No. 01-4625 · Updated · Formula and assumptions shown below

Water flow rate 20.0 US gal/min
Water flow rate
75.7 L/min
= Water flow rate × 3.785411784
Valve flow coefficient Cv
10
Set in the form below
Pressure drop across valve
4 psi
Set in the form below
You enter
Valve flow coefficient Cv, Pressure drop across valve (psi)
You get
Water flow rate (US gal/min), Water flow rate (L/min)
Rounding
1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A Cv-to-GPM calculator estimates water flow in U.S. gallons per minute from a valve’s flow coefficient and the pressure drop across it. Enter Cv and pressure drop in psi; the calculator returns estimated GPM using the standard liquid-flow equation.

Formula

For water under the standard reference conditions, flow in U.S. gallons per minute is the valve coefficient multiplied by the square root of the pressure drop in pounds per square inch:

Q = Cv × √ΔP

  • Q is estimated flow, in U.S. gallons per minute (GPM).
  • Cv is the valve flow coefficient, a rated capacity number defined for the valve at specified reference conditions.
  • ΔP is the pressure difference from the valve inlet to its outlet, in psi.

The calculator also converts the result to liters per minute: L/min = GPM × 3.785411784, using the exact U.S. gallon-to-liter conversion. The displayed results are rounded to one decimal place; the underlying estimate can have more digits. Cv is not a unit of flow by itself: pressure drop is needed to estimate flow.

Worked Example

Using the calculator’s default values, Cv = 10 and ΔP = 4 psi:

  1. Take the square root of the pressure drop: √4 psi = 2 √psi.
  2. Multiply by the valve coefficient: Q = 10 × 2 = 20.000 GPM.
  3. Convert to liters per minute: 20.000 × 3.785411784 = 75.70823568 L/min.

Rounded as shown by the calculator, the result is 20.0 GPM, or 75.7 L/min.

Assumptions

  • The fluid is water with a specific gravity of 1.0 under the reference conditions used to rate Cv.
  • The entered pressure drop is the actual pressure difference across the valve while flowing, not merely the system’s supply pressure.
  • The valve is operating in a flow regime where the standard Cv equation is a reasonable estimate; piping, fittings and other system effects are not included.

How Cv Relates to Flow

Cv is a capacity rating used for control and other valves. In the customary U.S. definition, a valve with Cv of 1 passes 1 U.S. GPM of water when the pressure drop across it is 1 psi. The square-root relationship means that doubling the pressure drop does not double flow: it multiplies flow by √2, about 1.414. Doubling Cv, by contrast, doubles the calculated flow when the fluid and pressure drop stay the same.

For example, a valve with Cv = 10 at a 9 psi drop has a water-flow estimate of 10 × √9 = 30 GPM. This is a calculation at a particular pressure drop, not a promise that the valve will deliver 30 GPM in every installation. The actual flow depends on the system’s available pressure, valve position, fluid properties and restrictions elsewhere in the piping.

When to Use the Calculator

Use this conversion to make a quick estimate when you know a valve’s Cv and the pressure drop expected across it. It can help compare flow capacity at a defined operating point, check a design estimate, or convert a known valve rating into a familiar flow unit. For a control valve, make sure the Cv corresponds to the intended opening or travel: a valve’s effective Cv can change substantially as it moves.

The pressure drop must be across the valve itself. A pump’s discharge pressure or the difference between a pump outlet and an unrelated reference point is not automatically the valve’s ΔP. Pressure is consumed by the whole flow path, including pipes, fittings, filters and other equipment. If the pressure readings are taken at different locations, account for what lies between them before using the result as the valve pressure drop.

Other Fluids and Important Limits

The displayed equation assumes water. For a liquid with a different specific gravity, a common incompressible-liquid form is:

Q = Cv × √(ΔP / SG)

Here, SG is the liquid’s specific gravity relative to water. A denser liquid (higher SG) has lower flow at the same Cv and pressure drop under this simplified model. Use a reliable value for the actual liquid and operating temperature; do not assume water’s SG for another fluid. Viscosity can also matter, especially for viscous liquids or small passages, so the simple equation may not predict real flow adequately.

Gas and vapor flow are not reliably calculated by treating them as water. Their behavior depends on absolute upstream pressure, temperature, molecular properties and whether flow becomes choked. Use a suitable gas-sizing method and the valve manufacturer’s data for those cases. The water calculator is also not a substitute for a complete valve selection: noise, cavitation, flashing, allowable velocity and control stability may affect suitability.

Common Errors and Valve Selection

  • Using the wrong pressure units: this calculator expects psi. A value entered in kPa or bar will produce an invalid result unless converted first. For reference, 1 bar is approximately 14.5038 psi and 1 kPa is approximately 0.145038 psi.
  • Using total system pressure instead of valve ΔP: use inlet pressure minus outlet pressure at the valve under the relevant flow condition.
  • Confusing Cv with a flow rate: Cv alone does not tell you GPM; pressure drop is part of the calculation.
  • Ignoring the fluid: the calculator’s direct result is for water, not every liquid, gas or vapor.
  • Relying on excessive precision: a one-decimal display does not mean the inputs or assumptions are accurate to that level. Valve data, pressure measurements and system conditions limit the meaningful precision.

For selection, estimate the flow range the system needs and the pressure drop available across the valve at that flow. Then compare the required capacity with the valve’s Cv at its intended operating position, using the manufacturer’s sizing information and appropriate standards. A valve that is much larger than needed may operate mostly near closed, where control can be poor; a valve that is too small may restrict maximum flow. The calculator alone cannot determine the correct valve size.

Frequently Asked Questions

How do I convert Cv to GPM?
For water, multiply Cv by the square root of the pressure drop in psi: GPM = Cv × √ΔP. Without ΔP, Cv cannot be converted to a single flow rate.

What pressure drop should I enter?
Enter the pressure difference between the valve inlet and outlet at the flow condition you want to estimate. Do not substitute the pump’s rated pressure or the system’s full supply pressure unless it truly equals the pressure drop across the valve.

Does Cv equal GPM?
Only when the pressure drop is 1 psi and the fluid is water at the applicable reference conditions. At other pressure drops, calculate flow with the square-root equation.

Can I use this calculator for oil or another liquid?
The direct result assumes water. For an incompressible liquid, the simplified correction is GPM = Cv × √(ΔP / SG), where SG is the liquid’s specific gravity relative to water. Viscosity and operating conditions can require a more complete sizing method.

Can I use it for air or gas?
No. Gas flow requires a compressible-flow calculation that considers absolute pressure, temperature and possible choking. Use a gas-specific valve-sizing method instead.

Why does actual flow differ from the estimate?
The equation isolates the valve and assumes the entered pressure drop is accurate. In a real system, valve position, fluid properties, piping losses, fittings and other equipment affect pressure and flow, so the estimate may not match measured operation.

Related

Formula used
in cv | Valve flow coefficient Cv | - | 10 | 0
in dp | Pressure drop across valve | psi | 4 | 0
out gpm | Water flow rate | US gal/min | cv * sqrt(dp) | 1
out lpm | Water flow rate | L/min | gpm * 3.785411784 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →