molecalculator

Moles & Molar Mass

Cv for an Ideal Gas: Formula and Calculator

Calculator No. 01-4631 · Updated · Formula and assumptions shown below

Constant-volume heat capacity, Cv 12.4717 J/K
Molar constant-volume heat capacity
12.4717 J/(mol·K)
= Constant-volume heat capacity, Cv ÷ Amount of gas
Amount of gas
1 mol
Set in the form below
Molar heat capacity at constant volume
12.4717 J/(mol·K)
Set in the form below
You enter
Amount of gas (mol), Molar heat capacity at constant volume (J/(mol·K))
You get
Constant-volume heat capacity, Cv (J/K), Molar constant-volume heat capacity (J/(mol·K))
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

This calculator finds the constant-volume heat capacity, CV, of an ideal gas from its amount of gas and molar heat capacity. Enter the amount in moles and the molar heat capacity in joules per mole-kelvin; the result is the total heat capacity in joules per kelvin.

Formula

The total constant-volume heat capacity is the amount of gas multiplied by its molar constant-volume heat capacity:

CV = nCV,m

  • CV is the heat capacity of the whole gas sample, in J/K.
  • n is the amount of gas, in mol.
  • CV,m is molar heat capacity at constant volume, in J/(mol·K).

The molar value can be estimated from the ideal-gas equipartition model when the molecule’s active degrees of freedom are known. For a gas with f active quadratic degrees of freedom, CV,m = (f/2)R, where R = 8.31446261815324 J/(mol·K). The calculator instead takes molar heat capacity as an input because the value depends on the gas and temperature; it is not universal.

Worked Example

Using the calculator’s defaults, n = 1 mol and CV,m = 12.4717 J/(mol·K):

  1. Apply CV = nCV,m.
  2. CV = (1 mol)(12.4717 J/(mol·K)) = 12.4717 J/K.
  3. Rounded to the four decimal places displayed, CV = 12.4717 J/K. The molar output is 12.4717 J/(mol·K).

Assumptions

  • The sample is treated as an ideal gas in a single, well-defined thermodynamic state.
  • The entered molar heat capacity applies to the gas’s composition and temperature range.
  • Amount is in moles, with no conversion from mass or volume performed by this calculator.
  • The result describes heat capacity at constant volume, not the heat required for an arbitrary process.

What Cv Means for an Ideal Gas

Heat capacity tells how much energy must be transferred as heat to raise a system’s temperature by one kelvin under specified conditions. The subscript V means the volume is held constant. For a fixed amount of gas in a rigid container, a small temperature change is related to heat transfer by δQV = CVdT, provided the heat capacity is approximately constant over that temperature interval. If it varies appreciably, use the temperature-dependent value and integrate rather than multiplying by one constant.

In the ideal-gas model, internal energy depends only on temperature, not on volume or pressure. That makes the model especially useful for connecting heat input and temperature change. It does not mean that every real gas has the same heat capacity, or that the heat capacity is independent of temperature.

How Degrees of Freedom Set the Molar Value

In classical statistical mechanics, each independent quadratic degree of freedom contributes R/2 to molar heat capacity at constant volume. A monatomic ideal gas has three translational degrees of freedom, so its predicted molar heat capacity is (3/2)R = 12.4717 J/(mol·K). This is why that value is used as the calculator’s example default.

A rigid diatomic molecule at ordinary temperatures is often approximated as having three translational and two rotational degrees of freedom. The resulting classical estimate is (5/2)R = 20.7862 J/(mol·K). Molecular vibration can add heat capacity when vibrational modes become thermally accessible, and at sufficiently low temperatures quantum effects can reduce contributions that the classical model predicts. Polyatomic gases may have more rotational and vibrational modes, so a single universal number is not appropriate.

For a real calculation, obtain the molar heat capacity for the specific gas and temperature range from a reliable reference or a stated experimental data set. Check whether the source gives CV,m directly. Many tables instead report CP,m, the molar heat capacity at constant pressure.

Cv and Cp: The Important Difference

CP refers to heating at constant pressure, while CV refers to heating at constant volume. At constant pressure, a gas can expand and do pressure-volume work as it warms. At constant volume, it cannot expand its boundary, so heat input changes its internal energy without that expansion work.

For an ideal gas, molar heat capacities satisfy the Mayer relation:

CP,m − CV,m = R.

Thus, if a trustworthy ideal-gas CP,m value is available at the same conditions, subtract 8.31446261815324 J/(mol·K) to obtain CV,m. Do not subtract R from a total heat capacity unless the equation and units are first made consistent: the relation above is molar. For a sample containing n moles, the total difference is nR.

Using the Calculator and Interpreting the Result

Enter the amount in mol and the molar heat capacity in J/(mol·K). The first output is the total CV; the second reports the molar value implied by the inputs as a useful unit check. If the amount doubles while the gas state and molar heat capacity remain unchanged, the total heat capacity doubles. The molar heat capacity does not change merely because the sample is larger.

For a small temperature change at fixed volume, an approximate heat requirement is Q = CVΔT. For example, a 1 mol monatomic ideal gas with CV,m = 12.4717 J/(mol·K) requires approximately 124.717 J for a 10 K increase under the assumptions above. This is a heat-transfer estimate, not a prediction of the final pressure or a substitute for an energy balance that includes other work or energy transfers.

  • Keep the units consistent: mol times J/(mol·K) gives J/K.
  • Do not enter a value in J/(mol·°C) without recognizing that a temperature interval of 1 °C equals an interval of 1 K; the numerical heat-capacity value is the same for those interval units.
  • Do not confuse heat capacity per mole with total heat capacity, or CV with CP.
  • Keep enough significant figures through the calculation, then round the reported result to match the input data’s precision.

Limits of the Ideal-Gas Calculation

The arithmetic CV = nCV,m is simple, but choosing a valid CV,m is the main scientific judgment. The value can change with temperature, molecular structure, and the composition of a gas mixture. A mixture’s molar heat capacity can be estimated from mole-fraction-weighted component values when the mixture behaves ideally and the component values refer to the same temperature.

At high pressure or near condensation, real-gas interactions can make ideal-gas predictions inaccurate. Also, heat capacity may be defined for a particular path or state, so a tabulated value should be checked for its conditions and convention. This calculator does not infer heat capacity from pressure, temperature, or molecular identity; it multiplies the molar value supplied by the reader.

Frequently Asked Questions

What is Cv for an ideal gas?
There is no single value for all ideal gases. For a monatomic ideal gas, the classical molar value is CV,m = (3/2)R = 12.4717 J/(mol·K). Other gases have different values because their rotational and vibrational modes contribute differently.

Is Cv the same as molar heat capacity?
Not necessarily. CV commonly denotes the total heat capacity of a sample, in J/K, while CV,m is the molar heat capacity, in J/(mol·K). They are related by CV = nCV,m.

How do I calculate Cv from Cp?
For an ideal gas, use the molar relation CV,m = CP,m − R, with R = 8.31446261815324 J/(mol·K). Ensure both values are molar heat capacities and correspond to compatible conditions.

Does Cv depend on temperature?
It can. The degrees-of-freedom model is a useful guide, but vibrational modes and quantum effects make real molar heat capacities temperature-dependent. Use data measured or tabulated for the relevant temperature range when accuracy matters.

Why is Cv used for a rigid container?
A rigid container has constant volume, so its gas cannot do boundary expansion work as it warms. Under the ideal-gas model, heat transfer at fixed volume is directly related to the change in internal energy and temperature.

Related

Formula used
in n | Amount of gas | mol | 1 | 0
in cvm | Molar heat capacity at constant volume | J/(mol·K) | 12.4717 | 0
out cv | Constant-volume heat capacity, Cv | J/K | n * cvm | 4
out cvbar | Molar constant-volume heat capacity | J/(mol·K) | cv / n | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →