A Cv-to-CFM calculator estimates air volume flow from a valve’s flow coefficient, pressure conditions, and temperature. Enter Cv, upstream and downstream pressures, and gas temperature; the result is an estimated flow in cubic feet per minute (CFM), based on an ideal-gas approximation.
Formula
This calculator uses a simplified, subcritical gas-flow estimate based on the liquid Cv definition and ideal-gas density scaling:
Q = 14.4 × Cv × √[((P₁ − P₂)(P₁ + P₂)) / (101.325²)] × √[293.15 / (T + 273.15)]
- Q is estimated standard cubic feet per minute (scfm), referenced here to 20 °C and 101.325 kPa absolute.
- Cv is the valve flow coefficient, dimensionless under its customary convention: US gallons per minute of water at a 1 psi pressure drop.
- P₁ is upstream absolute pressure in kPa.
- P₂ is downstream absolute pressure in kPa.
- T is gas temperature in °C; adding 273.15 converts Celsius to kelvin.
- 101.325 is the number of kilopascals in one standard atmosphere. The factor 14.4 is an approximate conversion and calibration factor for this stated standard-air estimate.
The pressure term accounts for the difference in pressure and the average absolute pressure. The temperature term adjusts gas density relative to the stated reference temperature. This is not a universal valve-sizing equation: manufacturers’ gas-sizing methods apply additional expansion, pressure-ratio, specific-heat, and compressibility factors.
Worked Example
Using the defaults above: Cv = 1, P₁ = 200 kPa absolute, P₂ = 101.325 kPa absolute, and T = 20 °C.
- Calculate the pressure difference and sum: P₁ − P₂ = 98.675 kPa; P₁ + P₂ = 301.325 kPa.
- Evaluate the pressure ratio: (98.675 × 301.325) / (101.325 × 101.325) ≈ 2.8958.
- At 20 °C, the temperature adjustment is √(293.15 / (20 + 273.15)) = 1.
- Q = 14.4 × 1 × √2.8958 × 1 ≈ 24.50 scfm.
The calculator displays the result to two decimal places. The displayed unit is standard CFM (scfm), not the actual volume passing through the valve at line pressure.
Assumptions
- Air is treated as an ideal gas, with compressibility and humidity effects neglected.
- The flow is approximated as subcritical; the formula does not detect or correct for choked flow.
- Pressure inputs are absolute, not gauge pressures, and P₁ must be greater than P₂.
- The reference condition for scfm is 20 °C and 101.325 kPa absolute.
- The valve coefficient is used as a nominal Cv; fittings, piping, reducers, and installation effects are excluded.
When a Cv-to-CFM Estimate Is Useful
Cv describes a valve’s capacity, not a fixed flow rate. A valve with a stated Cv will pass different amounts of gas as the pressure conditions, temperature, gas properties, and valve opening change. A conversion can help with an initial comparison, a rough system estimate, or understanding how pressure affects capacity. It should not replace a valve manufacturer’s gas-sizing calculation for selection or safety-critical design.
Use the calculator when you have a Cv value and a clearly defined pair of absolute pressures. Check whether the published Cv is for the fully open valve or for a particular position; a control valve’s effective Cv changes with its opening. Also confirm the reference basis whenever comparing CFM figures, because standard-flow conventions may use different temperatures and pressures.
Absolute Pressure, Gauge Pressure, and Standard Flow
Absolute pressure is measured from a vacuum. Gauge pressure is measured relative to local atmospheric pressure. The formula requires absolute pressure because gas density and pressure ratios depend on the vacuum reference. If your readings are gauge pressures, add local atmospheric pressure to each reading before entering them. For example, at an atmospheric pressure of 101.325 kPa, a gauge reading of 200 kPa corresponds to 301.325 kPa absolute.
Standard CFM expresses the gas quantity as a volume at an agreed reference condition. Actual CFM (ACFM) is the volume at the actual line pressure and temperature. The same mass of gas occupies less volume at higher absolute pressure and more volume at higher temperature. Do not interpret a scfm answer as the physical volume inside a pressurized pipe.
Limits and Common Errors
- Entering gauge pressure as absolute: this changes the pressure ratio and can substantially distort the result. Convert first.
- Reversing the pressure readings: upstream pressure must exceed downstream pressure for this flow direction.
- Assuming Cv means CFM: Cv is a capacity coefficient defined using water; gas flow also depends on pressure, temperature, and gas properties.
- Confusing scfm with acfm: the output is referenced to standard conditions, not the local pipe conditions.
- Ignoring choking: gas flow through a valve can reach a maximum as downstream pressure falls. A basic estimate cannot establish the correct choked-flow capacity.
- Using air assumptions for another gas: molecular weight, heat-capacity ratio, and compressibility affect gas sizing. This calculator does not account for them.
The expression is intentionally an estimate, not a certified valve-sizing method. For a real design, consult the valve’s rated gas-flow data and the applicable sizing procedure, accounting for the gas, valve geometry, pressure recovery, piping, and operating range. For compressed-gas systems, follow applicable codes and have equipment sized and reviewed by qualified personnel.
Frequently Asked Questions
How do I calculate CFM from Cv?
There is no single exact conversion from Cv to CFM. You also need the gas, upstream and downstream absolute pressures, temperature, and a defined standard-flow reference. The calculator provides a simplified air estimate from those inputs.
Does Cv equal CFM?
No. Cv is a valve capacity coefficient based on water flow under a specified pressure drop. CFM is a volume-flow rate. Gas flow through a valve varies with pressure and temperature, so Cv alone cannot determine it.
Should I use absolute or gauge pressure?
Use absolute pressure for both upstream and downstream values. Convert a gauge reading by adding local atmospheric pressure. Do not mix absolute and gauge values in the same calculation.
What is the difference between CFM and SCFM?
CFM may mean actual volume at operating conditions, while SCFM means volume expressed at a stated standard pressure and temperature. Standards can vary, so check the reference conditions attached to a specification.
Can I use this for nitrogen or natural gas?
Not as an accurate sizing result. Gas properties differ from air, and the calculator has no gas-property correction. Use a suitable manufacturer or engineering sizing method for the specific gas and operating conditions.
Can this calculator predict choked flow?
No. It uses a simplified subcritical estimate and does not determine the choking threshold or calculate choked capacity. Use a recognized gas-valve sizing method when choking may occur.
Related
Formula used
in cv | Valve flow coefficient Cv | - | 1 | 0 in p1 | Upstream absolute pressure | kPa | 200 | 0.001 in p2 | Downstream absolute pressure | kPa | 101.325 | 0.001 in t | Gas temperature | °C | 20 | -273.15 out q | Air flow | scfm | 14.4 * cv * sqrt((p1 - p2) * (p1 + p2) / (101.325 * 101.325)) * sqrt(293.15 / (t + 273.15)) | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Calculator in Hindi: Meaning, Usage and Examples0.2000 mol/L
- Volume Strength Formula in Terms of Molarity11.20 volumes
- H2O2 Volume Strength to Molarity Calculator0.893 mol/L
- Volume Strength to Molarity: Formula and Calculator0.0409 mol/L
- Molar Volume: Definition, Formula, and Calculator22.414 L/mol
- Molar Volume of a Gas Calculator and Formula22.4140 L/mol