For an ideal gas, convert heat capacity at constant volume to heat capacity at constant pressure with Cp = Cv + nR, where n is the amount of gas and R is the ideal gas constant. This calculator takes Cv and the amount of gas, then returns Cp; it also reports the molar heat capacities so you can compare values independently of sample size.
Formula
For a sample containing n moles of an ideal gas:
Cp = Cv + nR
- Cp is the sample’s heat capacity at constant pressure, in J/K.
- Cv is the sample’s heat capacity at constant volume, in J/K.
- n is the amount of gas, in mol.
- R is the ideal gas constant, 8.31446261815324 J/(mol·K).
The molar form is Cp,m = Cv,m + R, with both molar heat capacities in J/(mol·K). The calculator’s input Cv is for the whole sample, so dividing it by n gives Cv,m. It adds R to that molar value to obtain Cp,m. In the sample-level equation, nR has units J/K, matching Cv and Cp.
Worked Example
Using the calculator defaults, Cv = 20.786 J/K and n = 1 mol:
- Calculate the pressure-volume contribution: nR = 1 mol × 8.31446261815324 J/(mol·K) = 8.314462618 J/K.
- Add it to Cv: Cp = 20.786 J/K + 8.314462618 J/K = 29.100462618 J/K, which rounds to 29.100 J/K.
- Find the molar constant-volume capacity: Cv,m = 20.786 J/K ÷ 1 mol = 20.786 J/(mol·K).
- Find the molar constant-pressure capacity: Cp,m = 29.100462618 J/K ÷ 1 mol = 29.100 J/(mol·K).
Assumptions
- The gas follows the ideal-gas model under the conditions of interest.
- Cv is the heat capacity of the same gas sample and uses J/K.
- The amount n is positive and expressed in moles.
- The comparison applies at the same temperature and for the same specified heat-capacity basis; real-gas effects and changes in molecular behavior with temperature are not modeled.
Why Cp Is Greater Than Cv
Heat capacity describes how much heat is needed to raise a system’s temperature by a specified amount. At constant volume, the gas cannot expand, so supplied heat changes its internal energy. At constant pressure, the gas generally expands as it warms. Some energy is associated with the expansion against the surroundings, so more heat is required for the same temperature rise. That is why Cp exceeds Cv by nR for an ideal gas.
The relation is an ideal-gas thermodynamic identity, not a claim that every gas sample has one universal value of Cp or Cv. The actual heat capacities depend on the gas and, in many cases, temperature. The difference Cp − Cv is the part fixed by the ideal-gas model and the amount of substance.
How to Use the Calculator
- Enter the sample’s Cv in joules per kelvin. If your value is in another unit, convert it before entering it.
- Enter n in moles. For example, convert millimoles to moles by dividing by 1,000.
- Read the first result, Cp, as the heat capacity of the entire sample. The next two results are per mole.
Keep the basis consistent. A value in J/(mol·K) is already molar and should not be entered as though it were a sample value in J/K. If you know molar Cv instead, multiply it by n to obtain the sample Cv before using this calculator, or use the molar relation directly: Cp,m = Cv,m + R.
Comparisons and Common Mistakes
Cp and Cv are not interchangeable. Cp refers to heating under constant pressure; Cv refers to heating at constant volume. Confusing the conditions can produce an incorrect energy calculation even if the units look right. For an ideal gas, the difference in molar heat capacities is R, approximately 8.314 J/(mol·K), not 8.314 J/K for every sample. The sample-level difference grows with n.
Another common source of error is mixing molar and total heat capacity. For 2 mol of ideal gas, Cp − Cv equals 2R, about 16.629 J/K for the sample. On a per-mole basis, Cp,m − Cv,m remains R. The factor n belongs in the total-sample equation but not in the molar equation.
Do not infer Cv solely from the gas being “ideal.” Ideal behavior specifies the relationship between Cp and Cv, but the value of Cv itself depends on the gas’s molecular degrees of freedom and temperature. Simple textbook values can be useful approximations over limited temperature ranges; accurate work should use appropriate heat-capacity data for the gas and conditions.
Limits and Practical Interpretation
The calculator assumes the input Cv is a valid, positive heat capacity for the sample. It does not identify the gas, determine Cv from molecular structure, or correct for non-ideal behavior. At high pressures or near condensation, real-gas effects can make the ideal relation insufficient. At temperatures where internal molecular motions become accessible, heat capacity may vary, so a value measured or tabulated at one temperature may not apply unchanged elsewhere.
For a temperature interval where heat capacity is approximately constant, heat added can often be estimated using q = CΔT for the relevant constant-pressure or constant-volume process. If heat capacity changes significantly with temperature, a single-value multiplication is not enough; the temperature-dependent capacity must be integrated over the interval. The Cp-to-Cv conversion alone does not give the heat transferred: the process, temperature change, and sample amount also matter.
Frequently Asked Questions
What is the formula to convert Cv to Cp for an ideal gas?
Cp = Cv + nR for a sample, or Cp,m = Cv,m + R on a molar basis. Use the form that matches whether your heat capacity is total or per mole.
Why is Cp higher than Cv?
At constant pressure, a gas can expand as it warms and does work on its surroundings. At constant volume, it does not expand, so less heat is needed for the same temperature increase.
Is Cp − Cv always equal to R?
For an ideal gas, the difference is R per mole. For a whole sample of n moles, the difference is nR. Real gases do not generally obey this exact relation.
Can I use Cv in J/(mol·K) directly?
Yes, if you use the molar equation Cp,m = Cv,m + R. For this calculator, which requests sample Cv in J/K, multiply your molar value by the number of moles first.
Does the conversion depend on the type of ideal gas?
The difference follows the same ideal-gas equation for any gas, but the starting Cv and resulting Cp depend on the substance and may vary with temperature.
Related
Formula used
in cv | Heat capacity at constant volume | J/K | 20.786 | 0 in n | Amount of gas | mol | 1 | 0 out cp | Heat capacity at constant pressure | J/K | cv + n * 8.31446261815324 | 3 out cvm | Molar heat capacity at constant volume | J/(mol·K) | cv / n | 3 out cpm | Molar heat capacity at constant pressure | J/(mol·K) | cp / n | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Calculator in Hindi: Meaning, Usage and Examples0.2000 mol/L
- Volume Strength Formula in Terms of Molarity11.20 volumes
- H2O2 Volume Strength to Molarity Calculator0.893 mol/L
- Volume Strength to Molarity: Formula and Calculator0.0409 mol/L
- Molar Volume: Definition, Formula, and Calculator22.414 L/mol
- Molar Volume of a Gas Calculator and Formula22.4140 L/mol