molecalculator

Moles & Molar Mass

Exponential Decay and Growth Formula Calculator

Calculator No. 01-4463 · Updated · Formula and assumptions shown below

Amount after elapsed time 164.8721 units
Percentage change
64.87 %
Result, rounded to 2 decimal places
Starting amount
100 units
Set in the form below
Rate constant
0.05 1/time
Set in the form below
You enter
Starting amount (units), Rate constant (1/time), Elapsed time (time units)
You get
Amount after elapsed time (units), Percentage change (%)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The exponential growth and decay formula is N(t) = N0ekt, where a positive rate constant k describes growth and a negative one describes decay. This calculator finds the amount remaining or accumulated after a chosen time from the starting amount, rate, and elapsed time; it also reports the percentage change.

Formula

The continuous exponential growth or decay model is:

N(t) = N0ekt

  • N(t) is the amount after elapsed time t, in the same units as the starting amount.
  • N0 is the amount at time zero.
  • e is the mathematical constant approximately 2.71828.
  • k is the continuous rate constant, in reciprocal time units, such as per year or per hour.
  • t is elapsed time, using the same time unit that defines k.

The calculator uses N(t) = N0 × exp(k × t). Its percentage-change output is 100 × (exp(kt) − 1). A positive result indicates growth; a negative result indicates decay. The units chosen for k and t must match so their product is dimensionless.

Worked Example

Using the calculator’s defaults, the starting amount is 100 units, the continuous rate constant is 0.05 per time unit, and the elapsed time is 10 time units.

  1. Multiply rate by time: kt = 0.05 × 10 = 0.5.
  2. Calculate the amount: N(t) = 100 × e0.5 = 164.872127.
  3. Rounded to four decimal places, the amount is 164.8721 units.
  4. Calculate percentage change: 100 × (e0.5 − 1) = 64.872127%, or 64.87% to two decimal places.

The calculation predicts an increase of about 64.87% over the selected interval under the assumed constant-rate model.

Assumptions

  • The rate constant remains constant throughout the elapsed time.
  • The process follows a continuous exponential model, rather than a fixed number of discrete percentage changes.
  • The starting amount is nonnegative, and the model does not impose a carrying capacity, minimum amount, or other external limit.
  • The time unit used for the rate constant matches the elapsed-time unit.

How Growth and Decay Work

Exponential change occurs when the rate of change is proportional to the amount currently present. In differential form, this relationship is dN/dt = kN. Solving it gives N(t) = N0ekt. Because the change depends on the current amount, equal time intervals do not add or subtract equal quantities: each interval changes the amount by a similar proportion instead.

When k > 0, the amount grows. When k < 0, it decays toward zero. When k = 0, the model predicts no change. A negative rate does not make the calculated amount negative; with a positive starting amount, the exponential result remains positive.

This model can describe idealized situations such as constant proportional growth or first-order loss. It is not automatically appropriate just because measurements rise or fall. Real systems may have changing rates, resource limits, delays, or multiple processes that make a single exponential a poor fit.

Choosing the Rate and Time Units

The rate constant and elapsed time must use compatible units. If a quantity decays at 0.2 per day, enter time in days. For 3 days, kt = −0.2 × 3 = −0.6. If time is instead entered in hours, convert the rate to the equivalent hourly rate first: 0.2 per day is 0.2/24 per hour.

Rate conventions matter. The calculator accepts the continuous rate constant k, not a percentage change per period. For example, a 5% increase per period for one period is a discrete multiplier of 1.05. Its equivalent continuous rate for that period is ln(1.05), approximately 0.04879 per period. Simply entering 0.05 into the continuous model gives a factor of e0.05, approximately 1.05127, a slightly different increase.

For decay, the rate constant is often written with a minus sign. A half-life is a related way to express the same model. If an amount halves in time T1/2, then k = −ln(2)/T1/2. Conversely, the half-life is T1/2 = ln(2)/|k| when k is negative.

Reading Results and Common Mistakes

The amount output is expressed in the same units as the starting amount. The percentage-change output is relative to that starting amount; it is not the final amount as a percentage. For example, a 64.87% increase means a final amount of 164.87% of the initial amount.

  • Mixing units: Using a per-year rate with time in days changes the exponent incorrectly. Convert one so both use the same time basis.
  • Using the wrong rate convention: A discrete percentage per period is not exactly the same as a continuous rate constant.
  • Entering a positive decay rate: In this formula, decay requires a negative k. A positive value calculates growth.
  • Confusing percentage change with the final percentage: The formula reports change from the starting value; add 100% to the percentage change to express the final amount as a percentage of the start.
  • Overinterpreting precision: More displayed digits do not make an estimated rate or measurement more accurate. Round the result to suit the quality of the inputs.

When the Model Is Useful—and Its Limits

Use exponential growth or decay when evidence supports a roughly constant proportional rate over the interval of interest. A fitted value of k should be treated as an estimate tied to the data, conditions, and time span from which it came. If the rate changes, a single constant-rate calculation can be misleading, especially when projecting far beyond observed measurements.

Growth is often limited in practice. A population, for instance, may grow exponentially for a while but slow as resources become scarce. A simple exponential model has no such ceiling. Likewise, decay in a real system may include several components with different rates, so the total may not follow one exponential curve.

The calculator is a mathematical projection, not a source of measured rates. Obtain k from suitable observations, a stated model, or a reliable reference for the specific situation. When measurements are available, compare predicted and observed values and check whether a constant-rate model is credible.

Frequently Asked Questions

What is the formula for exponential decay?
Use N(t) = N0e−λt, where λ is a positive decay constant. This is the same model as N(t) = N0ekt with k = −λ.

What is the formula for exponential growth?
Use N(t) = N0ekt with a positive constant k. The amount grows by a proportion related to its current size.

How do I calculate a decay constant from half-life?
For half-life T1/2, the signed rate is k = −ln(2)/T1/2. Use the same time unit for the half-life and the rate.

Can the rate constant be zero?
Yes. If k = 0, then ekt = 1 and the amount stays equal to its starting value.

Why is my decay result not decreasing?
Check that the rate constant is negative and that the elapsed time is positive. A positive rate produces growth in this formula, while a negative rate produces decay.

Related

Formula used
in n0 | Starting amount | units | 100 | 0
in k | Rate constant | 1/time | 0.05 | -
in t | Elapsed time | time units | 10 | 0
out nt | Amount after elapsed time | units | n0 * exp(k * t) | 4
out pct | Percentage change | % | (exp(k * t) - 1) * 100 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →