molecalculator

Moles & Molar Mass

Density and Pressure: How They Relate

Calculator No. 01-1693 · Updated · Formula and assumptions shown below

Pressure increase 98,066 Pa
Pressure increase
98.067 kPa
= Pressure increase ÷ 1000
Fluid density
1000 kg/m^3
Set in the form below
Gravitational acceleration
9.80665 m/s^2
Set in the form below
You enter
Fluid density (kg/m^3), Gravitational acceleration (m/s^2), Depth below surface (m)
You get
Pressure increase (Pa), Pressure increase (kPa)
Rounding
0 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Density and pressure are related, but there is no single formula that connects them in every situation. For a fluid at rest, pressure changes with depth according to its density and gravity; for a gas, pressure, density, and temperature are linked by the ideal-gas law. This calculator finds the hydrostatic pressure change from fluid density, gravity, and depth.

Formula

For a fluid at rest with constant density, the pressure increase between two heights is:

ΔP = ρgh

  • ΔP is the pressure increase, in pascals (Pa).
  • ρ is the fluid density, in kilograms per cubic metre (kg/m³).
  • g is gravitational acceleration, in metres per second squared (m/s²).
  • h is the vertical depth difference, in metres (m).

The calculator reports ΔP, not absolute pressure. To estimate absolute pressure below an open liquid surface, add the surface pressure: Pabsolute = Psurface + ρgh. The units work because kg/(m·s²) equals a pascal. The second output converts pascals to kilopascals using 1 kPa = 1,000 Pa.

Worked Example

Using the calculator’s default values—water density 1,000 kg/m³, gravitational acceleration 9.80665 m/s², and depth 10 m:

ΔP = ρgh
ΔP = (1,000 kg/m³)(9.80665 m/s²)(10 m)
ΔP = 98,066.5 Pa
ΔP = 98.067 kPa

The pressure increase is therefore 98,067 Pa when rounded to the calculator’s whole-pascal display, or 98.067 kPa to three decimal places. If the water surface is exposed to standard atmospheric pressure, about 101.325 kPa, the absolute pressure at that depth is about 199.392 kPa. The calculator’s first result is the increase alone.

Assumptions

  • The fluid is stationary, continuous, and has uniform density throughout the stated depth.
  • Gravity is constant over the depth and is set to 9.80665 m/s², the conventional standard value; local gravity varies slightly by location and altitude.
  • Depth is a vertical difference, not the length of a sloping route through the fluid.
  • The output is a pressure difference. Surface pressure is excluded unless added separately.

How Density and Pressure Relate

Density is mass per unit volume; pressure is force per unit area. They describe different properties, so density alone does not determine pressure. The relationship depends on the physical situation and on other variables such as depth, temperature, and whether the material is a liquid, gas, or solid.

In a stationary liquid, deeper points support the weight of more liquid above them. A denser liquid has more mass in each unit of volume, so a given depth produces a larger pressure increase. For example, at the same depth and under the same gravity, a liquid with twice the density produces twice the hydrostatic pressure difference.

Pressure in a fluid acts in all directions at a point. The hydrostatic equation concerns how pressure changes with vertical position; it does not mean pressure pushes only downward. In a connected fluid at rest, points at the same height have equal pressure when they are in the same continuous fluid and there are no other forces or density variations to account for.

Why Gas Pressure Also Depends on Density

For an ideal gas, pressure and mass density are related by P = ρRsT, where P is absolute pressure in pascals, ρ is gas density in kg/m³, T is absolute temperature in kelvins, and Rs is the gas-specific constant in J/(kg·K). For a particular gas, Rs is the universal gas constant divided by that gas’s molar mass expressed in kg/mol.

This relation shows why density and pressure cannot be compared without specifying temperature and gas identity. At a fixed temperature for the same ideal gas, greater density means greater absolute pressure. At fixed pressure, heating an ideal gas generally lowers its density if it can expand. Real gases can depart from the ideal-gas model, especially at high pressure or near condensation.

Do not apply the liquid formula ΔP = ρgh to estimate the pressure of a gas in a sealed container. That is a different problem, governed by the container’s volume, gas amount, temperature, and possibly non-ideal behavior. Nor does a gas’s density by itself reveal its pressure unless the temperature and gas composition are known.

Using the Calculator and Interpreting Results

Enter density in kg/m³, gravity in m/s², and vertical depth in metres. The default density is a convenient approximate value for water; actual water density changes with temperature, dissolved material, and pressure. For another fluid, use a density appropriate to that substance and its conditions rather than treating the default as universal.

  • Use a pressure difference when comparing two depths or calculating the pressure added by a liquid column.
  • Add the pressure at the fluid surface to obtain absolute pressure at depth. For a vessel with a sealed or pressurized surface, use that actual surface pressure.
  • Use consistent units. Convert centimetres to metres by dividing by 100; convert g/cm³ to kg/m³ by multiplying by 1,000.
  • Use the vertical distance between points. A 10 m-deep point has the same hydrostatic pressure increase whether the route to it is straight or along a bent pipe.

A pressure gauge commonly reports pressure relative to the surrounding atmosphere (gauge pressure), whereas absolute pressure includes atmospheric pressure. The distinction matters for calculations involving gases, vacuum, and sealed systems. This calculator gives a change in pressure, so it can be added to a known starting pressure only after the reference is clear.

Limits and Common Misconceptions

The simple liquid equation assumes density does not vary with depth. If the fluid is layered or its density changes substantially, pressure change is found by integrating density times gravity over vertical distance; for layers of constant density, calculate each layer’s contribution and add them. In accelerating fluids, rotating systems, or flowing fluids, additional effects can alter the pressure distribution.

A common misconception is that denser objects always experience higher pressure. An object’s density does not set the surrounding fluid pressure: the fluid’s density, depth, gravity, and boundary conditions do. An object’s density does affect whether it tends to float or sink, but that is a buoyancy question, not a direct pressure rule.

Another mistake is to confuse pressure with force. Pressure is force divided by area, so the same pressure acting on a larger surface produces a larger total force. Likewise, doubling fluid density doubles the hydrostatic pressure difference only when depth and gravity stay the same.

Frequently Asked Questions

Does higher density mean higher pressure?
Not by itself. At the same depth in the same gravitational field, a denser stationary fluid produces a greater pressure increase. For a gas, pressure also depends on temperature and gas identity.

What is the formula for pressure from density?
For a stationary fluid of uniform density, the pressure difference is ΔP = ρgh. For an ideal gas, the relation is P = ρRsT, using absolute pressure and temperature.

How much pressure does water add per metre of depth?
Using water density 1,000 kg/m³ and standard gravity 9.80665 m/s², each metre adds about 9,806.65 Pa, or 9.807 kPa. The actual value varies slightly with water density and local gravity.

Is pressure at depth absolute or gauge pressure?
The value ρgh is the pressure increase relative to the surface. If the surface is open to the atmosphere, that increase is gauge pressure relative to atmospheric pressure; absolute pressure is the increase plus atmospheric pressure.

Does density change with pressure?
It can. Liquids are usually only slightly compressible under ordinary conditions, while gases can change density substantially as pressure or temperature changes. The direction and size of the change depend on the substance and conditions.

Related

Formula used
in rho | Fluid density | kg/m^3 | 1000 | 0
in g | Gravitational acceleration | m/s^2 | 9.80665 | 0
in h | Depth below surface | m | 10 | 0
out dp | Pressure increase | Pa | rho * g * h | 0
out dpk | Pressure increase | kPa | dp / 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →