molecalculator

Moles & Molar Mass

Density of a Quarter: Mass, Volume, and Calculation

Calculator No. 01-1703 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The density of a U.S. quarter is about 7.1 g/cm³, using its current standard mass of 5.670 g and diameter of 24.26 mm to estimate its volume as a cylinder. The exact value depends on the coin’s thickness and condition, so this calculator estimates density from mass, diameter, and thickness rather than treating every quarter as identical.

Formula

The calculator treats the coin as a flat cylinder. Density is mass divided by volume:

ρ = m ÷ [π(d ÷ 2)²t]

  • ρ is estimated density, in grams per cubic centimetre (g/cm³).
  • m is the coin’s mass, in grams. The formula converts grams to kilograms by dividing by 1000.
  • d is diameter, in millimetres. It is converted to metres by dividing by 1000, then halved to get the radius.
  • t is thickness, in millimetres, converted to metres by dividing by 1000.
  • π is pi, approximately 3.14159.

The cylinder volume is calculated in cubic metres. To express density in g/cm³, the calculator’s combined unit conversion is equivalent to converting mass to kilograms and volume to cubic metres, finding kg/m³, then dividing by 1000. The second output shows the same estimate in kg/m³; 1 g/cm³ equals 1000 kg/m³.

Worked Example

Using the default values—mass 5.670 g, diameter 24.26 mm, and thickness 1.75 mm—first convert the dimensions:

  • Mass: 5.670 g ÷ 1000 = 0.005670 kg.
  • Diameter: 24.26 mm ÷ 1000 = 0.02426 m; radius = 0.02426 m ÷ 2 = 0.01213 m.
  • Thickness: 1.75 mm ÷ 1000 = 0.00175 m.

Volume = π × (0.01213 m)² × 0.00175 m ≈ 8.0881 × 10-7 m³.

Density = 0.005670 kg ÷ (8.0881 × 10-7 m³) ≈ 7010.9 kg/m³, or ≈ 7.01 g/cm³. Rounded to the calculator’s two decimal places, the displayed estimate is 7.01 g/cm³, equivalent to 7011 kg/m³ rounded to a whole number.

What a Quarter Is Made Of

A modern U.S. quarter-dollar coin is a copper-nickel clad coin. The U.S. Mint specifies a mass of 5.670 g, a diameter of 24.26 mm, and a thickness of 1.75 mm. Its outer layers are copper-nickel alloy, bonded to a copper core. Because the coin is layered, its bulk density reflects the combined mass and volume of these materials, not the density of one pure metal.

The result from the cylinder model is close to 7.1 g/cm³, a useful approximate value for a typical current quarter. It is not a direct measurement of the alloy’s intrinsic density: the calculation simplifies the coin’s shape and uses rounded dimensions. A more precise result would require measuring the coin’s actual displaced volume or using sufficiently precise geometric measurements.

How to Use the Calculator

For the default estimate, leave the inputs unchanged. For a particular coin, weigh it and measure its diameter and thickness, then enter the readings in the displayed units. Use the coin’s full diameter, not its radius. Thickness is the distance from one flat face to the other; avoid including a raised design as though it were the thickness of the entire disk.

Mass and dimensions should refer to the same coin. A worn, damaged, dirty, or unusual coin may not match standard specifications. Measurement resolution matters: because the volume is small, a modest error in thickness can noticeably affect the calculated density. The result is best interpreted as an estimate, not as a coin-authentication test.

Accuracy, Limits, and Common Misconceptions

  • Density is not mass. A quarter’s standard mass is 5.670 g; its density is mass divided by volume and is expressed here in g/cm³.
  • The calculator assumes a perfect cylinder. Real coins have raised designs, a rim, and fine edge details, so their shape is not exactly a smooth cylinder.
  • Units must match the inputs. Enter grams and millimetres as labelled. Entering centimetres or inches without conversion produces a misleading result.
  • Density alone does not prove authenticity. Different materials or combinations of materials can yield similar bulk densities. Weight, dimensions, appearance, and other checks may all matter.

A related question is whether a quarter’s density equals the density of copper or nickel. It does not: the coin is a copper-nickel composite with a copper core, and its measured bulk density is based on the complete coin. The answer also need not be exactly the calculator’s default because real measurements, rounding, wear, and the geometric approximation affect the result.

Frequently Asked Questions

What is the density of a U.S. quarter?
A typical current U.S. quarter has an estimated density around 7.1 g/cm³. Using the standard dimensions and mass in the calculator’s cylinder model gives about 7.01 g/cm³.

What is the mass of a quarter?
The specified mass of a current U.S. quarter is 5.670 g. Older or worn coins may differ, so weigh a specific coin if its individual mass matters.

What is a quarter’s volume?
Approximating a standard quarter as a cylinder gives about 0.809 cm³ from its stated diameter and thickness. The actual coin’s relief and edge details make its exact volume more complicated to calculate geometrically.

Is a quarter made of solid copper or nickel?
No. A modern U.S. quarter is copper-nickel clad, with copper-nickel outer layers and a copper core. Its density reflects the whole layered coin.

Can density tell me if a quarter is real?
Not reliably by itself. The estimate depends on measurement accuracy and a simplified shape model, and density is not a unique identification test. Use other appropriate checks as well.

Assumptions

  • The coin is modeled as a uniform, flat cylinder.
  • Mass and dimensions are measured accurately and use the stated units.
  • The result is an approximate bulk density; it does not identify the coin’s composition or authenticity.

Related

Formula used
in m | Quarter mass | g | 5.670 | 0
in d | Quarter diameter | mm | 24.26 | 0
in t | Quarter thickness | mm | 1.75 | 0
out rho | Estimated density | g/cm^3 | (m / 1000) / (pi * (d / 1000 / 2)^2 * (t / 1000)) * 1000 | 2
out si | Estimated density | kg/m^3 | rho * 1000 | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →