The density of copper sulfate depends on its form: anhydrous copper sulfate (CuSO₄) has a density of about 3.60 g/cm³, while the common pentahydrate (CuSO₄·5H₂O) has a density of about 2.29 g/cm³. For a solution, the density varies with concentration and temperature—a saturated solution at 20 °C contains about 32 g of CuSO₄·5H₂O per 100 g of water and has a density of roughly 1.20 g/mL. This article explains these values, how they are measured, and how to use them in lab calculations.
Formula for Density
Density (ρ) is mass divided by volume: ρ = m / V.
- ρ – density, in g/cm³ (equivalent to g/mL) for solids, or g/mL for solutions.
- m – mass of the substance or solution, in grams.
- V – volume, in cm³ or mL.
For a solid sample, measure the mass and the volume (by water displacement or geometry). For a solution, measure a known volume and its mass; the density is the mass divided by that volume. The calculator above estimates the density of a solution prepared by dissolving a given mass of CuSO₄·5H₂O in water, assuming the final volume equals the volume of water plus the volume of solute (an approximation that works well for dilute solutions).
Worked Example
Using the default values: 25.0 g of CuSO₄·5H₂O dissolved in enough water to make 250 mL of solution.
- Mass concentration: 25.0 g / (250 mL / 1000) = 25.0 / 0.250 = 100.0 g/L.
- Molar mass of CuSO₄·5H₂O: Cu 63.546 + S 32.065 + O₄ 63.996 + 5×H₂O 90.078 = 249.685 g/mol.
- Moles: 25.0 g / 249.685 g/mol = 0.10013 mol.
- Molarity: 0.10013 mol / 0.250 L = 0.4005 mol/L.
- Approximate density: (25.0 g + 250 g) / 250 mL = 275 / 250 = 1.100 g/mL (assuming water density 1.00 g/mL and no volume change).
The calculator gives the same: 100 g/L, 0.4005 mol/L, and 1.100 g/mL.
Assumptions
- The solution is at room temperature (~20 °C).
- The density of water is taken as 1.00 g/mL.
- Dissolving copper sulfate does not change the total volume significantly (valid for dilute solutions).
- The solid is pure CuSO₄·5H₂O.
Background: Why Copper Sulfate Has Two Densities
Copper sulfate is commonly encountered as the bright blue pentahydrate (CuSO₄·5H₂O), which contains water of crystallization. When heated, it loses this water to become the white or gray anhydrous form (CuSO₄). The anhydrous form is denser because the water molecules are removed, leaving a more compact crystal lattice. The pentahydrate’s density of 2.29 g/cm³ and anhydrous density of 3.60 g/cm³ are widely cited in handbooks. These values are for crystalline solids, not powders—a powder will have a lower bulk density due to air between particles.
How to Measure Density of a Solid or Solution
For a solid crystal, the simplest method is water displacement: record the volume of water in a graduated cylinder, add the crystal, and read the new volume. The difference is the crystal’s volume. Divide the mass by that volume. For a solution, use a volumetric flask: weigh an empty flask, add a known volume of solution, weigh again, and compute density. Alternatively, use a hydrometer or a pycnometer for greater accuracy.
Common Mistakes and Misconceptions
- Confusing the density of the solid with the density of a solution. A 1 M solution is not 3.60 g/mL; it is about 1.12 g/mL.
- Ignoring temperature. Solution density decreases as temperature rises; always note the temperature.
- Using the anhydrous molar mass (159.61 g/mol) when weighing the pentahydrate. This leads to errors in concentration calculations.
- Assuming that dissolving a solid always increases the volume by the solid’s volume. In practice, the final volume may differ; measuring the final volume is essential.
Practical Uses of Density
Density is used to convert between mass and volume in preparing solutions. For example, if you need 500 mL of a copper sulfate solution with a density of 1.10 g/mL, the total mass is 550 g. If you know the mass fraction, you can calculate how much solid to weigh. Density also helps in quality control: a solution with the wrong density likely has the wrong concentration. In electroplating or agriculture, density measurements are a quick check on concentration.
Safety and Handling
Copper sulfate is harmful if swallowed and can irritate skin and eyes. Wear gloves and eye protection when handling the solid or concentrated solutions. Avoid inhaling dust. Follow your lab’s safety data sheet (SDS) and your supervisor’s instructions. Dispose of copper sulfate solutions as hazardous waste, not down the drain.
Frequently Asked Questions
What is the density of copper sulfate in g/mL? For the solid pentahydrate, it is about 2.29 g/mL. For a 1 M solution, it is approximately 1.12 g/mL. The anhydrous solid is 3.60 g/mL.
How does concentration affect solution density? The more copper sulfate dissolved, the denser the solution. A saturated solution at 20 °C has a density around 1.20 g/mL. Each concentration has a characteristic density, which is why density can be used to estimate concentration.
Why does copper sulfate have different densities? The pentahydrate includes water molecules in its crystal structure, making it less dense than the anhydrous form. The water adds mass but also increases volume disproportionately.
Can I use density to find the molarity of a copper sulfate solution? Yes, if you have a density-concentration table or a calibration curve. Measure the density, then look up the corresponding molarity. This is a common method in industrial settings.
Is the density of copper sulfate the same as its specific gravity? Specific gravity is the ratio of the substance’s density to the density of water (at a specified temperature). For solids, the numeric value is close but not identical unless water is at 4 °C. For solutions, specific gravity is often measured with a hydrometer.
Does temperature change the density of a saturated copper sulfate solution? Yes. Solubility increases with temperature, so a hot saturated solution has a higher concentration and higher density than a cold one. Always record the temperature when measuring density.
Related
Formula used
in m | Mass of copper sulfate (CuSO₄·5H₂O) | g | 25.0 | 0 in v | Solution volume | mL | 250 | 0.001 out c | Mass concentration (g/L) | g/L | m / (v / 1000) | 2 out m | Molarity (mol/L) | mol/L | (m / 249.685) / (v / 1000) | 4 out d | Approx. solution density (g/mL) | g/mL | (m + v) / v | 3
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check