This calculator converts a volume of gas in standard cubic feet (SCF) to its mass in pounds (lbs) using the ideal gas law. You enter the gas volume in SCF, its molecular weight, and the standard conditions (temperature and pressure) that define your SCF, and you get the mass in pounds. This is useful for estimating gas cylinder contents, calculating emissions, or sizing gas handling equipment.
Formula
The ideal gas law, PV = nRT, is rearranged to solve for the number of moles (n) and then multiplied by the molecular weight to get mass. In US customary units, the equation for mass in pounds is:
m (lb) = [V (SCF) × P (psia) × 144] / [R × T (°R)] × MW (lb/mol)
Where:
- V = gas volume in standard cubic feet (SCF)
- P = absolute pressure in pounds per square inch absolute (psia)
- 144 = conversion factor from square inches to square feet (in²/ft²)
- R = universal gas constant = 10.7316 (psia·ft³)/(lb·mol·°R)
- T = absolute temperature in degrees Rankine (°R) = °F + 459.67
- MW = molecular weight of the gas in pounds per pound-mole (lb/lb-mol). Note: the molecular weight in g/mol is numerically the same as in lb/lb-mol, so you can enter the g/mol value directly.
To get pounds, the result in lb-mol is multiplied by the molecular weight (lb/lb-mol). The calculator also shows the number of moles in mol (using 453.59237 g/lb).
Worked Example
Using the default values: V = 100 SCF, MW = 28.97 g/mol (air), T = 60 °F, P = 14.696 psia.
- Convert temperature to Rankine: T = 60 + 459.67 = 519.67 °R
- Calculate lb-mol of gas: n (lb-mol) = (100 × 14.696 × 144) / (10.7316 × 519.67) = 211,622.4 / 5,576.67 ≈ 37.947 lb-mol
- Convert lb-mol to mol: 37.947 lb-mol × 453.59237 mol/lb-mol = 17,214.7 mol
- Calculate mass: m = n × MW = 37.947 lb-mol × 28.97 lb/lb-mol ≈ 1,099.3 lb
The calculator shows 1099.3 lb (rounded to 3 decimals) and 17214.7 mol.
Assumptions
- The gas behaves as an ideal gas (PV = nRT). This is accurate for most gases at standard conditions and moderate pressures.
- Standard conditions are defined by the user. Common definitions include 60 °F and 14.696 psia (US customary), 0 °C and 101.325 kPa (SI), or 15 °C and 101.325 kPa (ISO).
- The molecular weight is for the pure gas or an average for a mixture (e.g., air = 28.97 g/mol).
- The gas is not supercritical or near its condensation point; the ideal gas law fails for real gases at high pressure or low temperature.
When to Use This Calculator
Use this conversion when you need to know the mass of a gas that occupies a certain volume at standard conditions. For example, to estimate the weight of gas in a cylinder (knowing the internal volume and pressure), to convert volumetric flow rates to mass flow rates in lb/hr, or to calculate gas emissions in pounds from a known volume in SCF.
Remember that SCF is a volume measured at a specific temperature and pressure. If your gas is at different conditions, you must first correct to standard conditions using the combined gas law, or use the actual conditions in this calculator (but then it is not SCF).
How to Read the Result
The first output, Mass (lb), is the weight of the gas. The second output, Amount of gas (mol), is the number of moles, which is useful for stoichiometric calculations. For air at 60 °F and 14.696 psia, 1 SCF weighs about 0.076 lb (this is the density of air at those conditions).
For other gases, the mass per SCF is proportional to molecular weight: helium (4.00 g/mol) weighs much less than propane (44.1 g/mol).
Common Mistakes
- Using gauge pressure (psig) instead of absolute (psia): Standard conditions use absolute pressure. Gauge pressure is relative to atmospheric; add 14.696 to psig to get psia.
- Forgetting to convert °F to °R: The gas law requires absolute temperature. Add 459.67 to °F.
- Mixing up molecular weight units: The molecular weight in g/mol is numerically equal to lb/lb-mol, so you can enter the same number. But do not use kg/kmol without adjusting.
- Using the wrong gas constant: The constant 10.7316 is for psia·ft³/(lb·mol·°R). If you use a different pressure or volume unit, you must use the corresponding constant.
- Assuming SCF is always at 60 °F and 14.696 psia: Some industries use 59 °F, 15 °C, or 101.325 kPa. Always check your standard conditions.
Tips
- For a real gas at high pressure (e.g., > 500 psia) or near its critical point, use a compressibility factor (Z) or an equation of state for better accuracy. This calculator assumes Z = 1.
- If you have a gas mixture, use the average molecular weight. For air, that is 28.97 g/mol.
- When measuring gas flow in SCFM (standard cubic feet per minute), multiply by 60 to get SCF per hour, then use this calculator to get lb/hr.
- Double-check your standard conditions: the calculator allows any temperature and pressure, but the result is only meaningful if you know what standard you are using.
Troubleshooting
Result seems too high or too low: Verify that your pressure is absolute (psia), not gauge. Check that temperature is in °F, not °C. For °C, convert to °F first: °F = °C × 9/5 + 32.
Getting an error for temperature below -459.67 °F: That is absolute zero. No gas can exist below that, so the calculator rejects it. If you are entering a very cold temperature, ensure you are using °F, not °C.
Molecular weight input is rejected: The minimum is 0.001 g/mol. For a gas, the lightest is hydrogen (about 2.016 g/mol). If you are using a mixture, ensure the average is above 0.001.
Mass output shows “Cannot compute”: This happens if any input is outside its allowed range. Check that pressure is positive and temperature is above absolute zero.
Frequently Asked Questions
What is SCF? SCF stands for Standard Cubic Foot, a unit of gas volume measured at a defined standard temperature and pressure. The most common US standard is 60 °F and 14.696 psia (1 atm).
How many pounds is 1 SCF of natural gas? Natural gas is mostly methane (MW ≈ 16.04 g/mol). At 60 °F and 14.696 psia, 1 SCF weighs about 0.042 lb (16.04/28.97 × 0.0765 lb). Use the calculator with MW = 16.04 to get the exact value.
Can I use this for any gas? Yes, as long as the gas behaves ideally at the given conditions. For most gases at standard conditions, this is a good approximation. For high pressures or near condensation, use a compressibility factor.
What is the difference between SCF and ACF? ACF is Actual Cubic Feet, measured at the actual temperature and pressure of the gas. SCF is normalized to standard conditions. To convert ACF to SCF, you use the combined gas law: SCF = ACF × (P_actual/P_standard) × (T_standard/T_actual).
Is the molecular weight in g/mol the same as in lb/lb-mol? Yes, the numerical value is the same because the definition of pound-mole uses the same Avogadro number but with pounds. So 28.97 g/mol = 28.97 lb/lb-mol.
Why does the calculator show moles as well as pounds? Moles are useful for chemical reactions and for converting to other units like kilograms (multiply by molecular weight in kg/mol). It also helps you verify the calculation.
Related
Formula used
in v | Gas volume | SCF | 100 | 0 in mw | Molecular weight | g/mol | 28.97 | 0.001 in t | Standard temperature | °F | 60 | -459.67 in p | Standard pressure | psia | 14.696 | 0 out lbs | Mass | lb | v * (p * 144) * mw / (10.7316 * (t + 459.67)) / 453.59237 | 3 out mol | Amount of gas | mol | v * (p * 144) / (10.7316 * (t + 459.67)) | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Relative Molecular Mass of Copper Sulfate0.0732 mol/L
- Bag Volume Calculator: How to Measure Any Bag25.50 L
- Molar Mass of Copper(II) Sulfate (CuSO₄)0.0468 mol/L
- Molar Mass of Hydrated Copper Sulphate (CuSO4·5H2O)0.0468 mol/L
- Molar Mass of Copper(II) Sulfate: Exact Value & How to Find It0.0732 mol/L
- Molar Mass of CuSO4: How to Calculate It0.1000 mol