molecalculator

Moles & Molar Mass

Pure Nitric Acid Density: Value and Calculation

Calculator No. 01-3631 · Updated · Formula and assumptions shown below

Density 1.5100 g/mL
Mass from volume
151.00 g
= Volume × Density
Volume from mass
100.00 mL
= Mass ÷ Density
Volume
100 mL
Set in the form below
You enter
Volume (mL), Mass (g)
You get
Density (g/mL), Mass from volume (g), Volume from mass (mL)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Pure nitric acid (100% HNO₃) has a density of about 1.51 g/mL at 20 °C, equivalent to about 1,510 kg/m³. This calculator estimates the mass of pure acid from its volume, or its volume from its mass, using that reference density; enter either quantity and the calculator returns the other.

Formula

Density is mass divided by volume: ρ = m / V. Rearranging gives mass m = ρ × V and volume V = m / ρ. Here, ρ is the reference density of pure nitric acid, 1.51 g/mL; m is mass in grams (g); and V is volume in millilitres (mL). The density value is a conventional approximate input, not a universal constant: temperature and the exact composition of a sample affect it. The calculator reports density directly and uses the entered volume or mass for the corresponding conversion.

Worked Example

Using the defaults, the reference density is 1.51 g/mL, the volume is 100 mL, and the mass is 151 g.

  • Density: ρ = 1.51 g/mL.
  • Mass from volume: m = ρ × V = 1.51 g/mL × 100 mL = 151 g.
  • Volume from mass: V = m / ρ = 151 g / (1.51 g/mL) = 100 mL.

The outputs are displayed to the number of decimal places specified in the calculator block. In this example, they are 1.5100 g/mL, 151.00 g, and 100.00 mL.

Assumptions

  • The material is pure nitric acid, treated as 100% HNO₃, not an aqueous commercial solution.
  • The density reference is approximately 1.51 g/mL near 20 °C; the calculation does not correct for temperature.
  • Volume means the measured volume of the acid itself. No dilution or mixing is represented.
  • This is a mass–volume conversion, not a method for preparing, handling, or transferring nitric acid.

What “Pure Nitric Acid” Means

Nitric acid is HNO₃, a molecular compound composed of hydrogen, nitrogen, and oxygen. In ordinary laboratory and industrial use, “pure” generally refers to material that is essentially undiluted, while real products may have specified purity limits and trace impurities. The density quoted for pure acid should not be applied automatically to a bottle labelled with a lower concentration.

The commonly encountered value near 1.51 g/mL is tied to a stated temperature and composition. Density is mass per unit volume, so a change in either temperature or concentration can change the measured value. The number is useful for a quick conversion, but a product specification or a reliable reference table for the exact concentration and temperature is preferable when precision matters.

Why Concentration and Temperature Matter

Nitric acid is often supplied as a water solution. Adding water changes the composition and therefore the density; the relationship is not simply proportional to the percentage of acid. For example, multiplying the pure-acid density by a solution’s percentage does not give the solution’s density. Use a density table or specification for that particular concentration instead.

Temperature matters because liquids generally expand as they warm. If the same amount of liquid occupies a larger volume, its density is lower. Thus, a density reported at 20 °C is not necessarily accurate for a sample measured at a substantially different temperature. For routine reference use, always state the temperature alongside the value.

Mass is generally a more stable quantity than volume when temperature changes. If a precise amount is needed for an approved analytical calculation, use the actual product concentration and appropriate density data rather than treating the approximate pure-acid figure as exact.

Using the Calculator and Reading the Result

Enter the volume in millilitres to estimate its mass, or enter the mass in grams to estimate its volume. The calculator shows both conversions using the reference density; interpret the result that matches the quantity you entered. Units cancel as expected: g/mL multiplied by mL gives g, while g divided by g/mL gives mL.

  • For a volume of 10 mL, the estimate is 1.51 × 10 = 15.1 g.
  • For a mass of 50 g, the estimate is 50 / 1.51 ≈ 33.1 mL.
  • For a litre, first note that 1 L = 1,000 mL; the corresponding estimate is about 1,510 g, or 1.51 kg.

These are arithmetic examples, not handling instructions. The displayed precision is not proof that the underlying density is known to four decimal places. The reference value itself is approximate, so extra digits in an output should not be mistaken for extra accuracy.

Common Misconceptions and Limits

A frequent error is to confuse pure nitric acid with concentrated nitric acid. “Concentrated” describes a solution with a high proportion of HNO₃, not necessarily 100% acid. Its density can differ from the pure-acid reference, and the exact value depends on the specified concentration and temperature. Another error is to assume that all nitric acid labels use the same concentration basis or purity specification; check the product documentation.

The calculator also cannot account for impurities, water uptake, temperature expansion, measurement uncertainty, or a volume change when substances are mixed. It is suitable for a basic density conversion and educational arithmetic, not for determining a sample’s composition. If the measured material is a solution, substitute a documented density for that solution rather than using 1.51 g/mL.

Safety and Scope

Nitric acid is a corrosive oxidizing acid that can cause severe burns and serious eye injury; some concentrations also release hazardous fumes. This page provides only a general calculation and is not a procedure for preparing, dispensing, or using the substance. Never handle nitric acid based on a density conversion alone. For any legitimate bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What is the density of pure nitric acid?
About 1.51 g/mL near 20 °C, or about 1,510 kg/m³. The exact value depends on temperature and purity.

Is nitric acid denser than water?
Yes. Water has a density close to 1.00 g/mL near room temperature, whereas pure nitric acid is about 1.51 g/mL near 20 °C.

What is the density of concentrated nitric acid?
There is no single value for every concentrated product. Density depends on its stated HNO₃ concentration and temperature, so consult the product specification or an appropriate density table.

How much does 100 mL of pure nitric acid weigh?
At the approximate reference density of 1.51 g/mL, 100 mL has an estimated mass of 151 g.

Does nitric acid density change with temperature?
Yes. Like other liquids, nitric acid expands or contracts with temperature, changing its density. Use a value reported for the sample’s temperature when accuracy is important.

Related

Formula used
in v | Volume | mL | 100 | 0
in m | Mass | g | 151 | 0
out d | Density | g/mL | 1.51 | 4
out mass | Mass from volume | g | v * d | 2
out vol | Volume from mass | mL | m / d | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →