molecalculator

Moles & Molar Mass

Dilution of Solutions: How to Calculate C₁V₁ = C₂V₂

Calculator No. 01-6613 · Updated · Formula and assumptions shown below

Final solution volume 100.000 mL
Solvent to add
90.000 mL
Result, rounded to 3 decimal places
Stock concentration
1 mol/L
Set in the form below
Target concentration
0.1 mol/L
Set in the form below
You enter
Stock concentration (mol/L), Target concentration (mol/L), Stock volume used (mL)
You get
Final solution volume (mL), Solvent to add (mL)
Rounding
3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Dilution of a solution is calculated with C₁V₁ = C₂V₂: multiply the starting concentration by the volume taken, then divide by the desired concentration to find the volume to dilute to. Enter the stock concentration, target concentration, and starting volume below; the calculator returns the final volume and how much solvent to add.

Formula

The dilution equation is C₁V₁ = C₂V₂. Rearranging gives V₂ = C₁V₁ / C₂, the final volume after dilution. The solvent volume to add is V₂ − V₁.

  • C₁ is the stock (starting) concentration, in mol/L.
  • V₁ is the volume of stock solution transferred, in mL.
  • C₂ is the target (final) concentration, in mol/L.
  • V₂ is the total final solution volume, in mL.

Because both volumes are expressed in the same unit, their units cancel in the ratio. Concentrations must also use the same unit. The calculator treats a target concentration above the stock concentration as impossible for simple dilution: it reports “Cannot compute” for the solvent-addition result rather than suggesting a negative volume.

Worked Example

Using the defaults, the stock is 1 mol/L, the target is 0.1 mol/L, and 10 mL of stock is used.

  1. Calculate the solute amount represented by the stock portion: 1 mol/L × 10 mL = 10 mol·mL/L.
  2. Divide by the target concentration: V₂ = (1 mol/L × 10 mL) ÷ 0.1 mol/L = 100 mL.
  3. Find the solvent volume: 100 mL − 10 mL = 90 mL.

The calculator therefore returns a final solution volume of 100.000 mL and a solvent addition of 90.000 mL. In practice, bring the mixture to a final volume of 100 mL; do not assume that adding exactly 90 mL of solvent always produces exactly 100 mL of total solution.

Assumptions

  • The same solute is present before and after dilution, and no solute is lost or added.
  • The stated concentrations refer to the same concentration convention, here molarity (mol/L).
  • The target concentration is no greater than the stock concentration; dilution alone cannot concentrate a solution.
  • The final volume means total solution volume, not the volume of solvent added.

When to Use the Dilution Equation

Use C₁V₁ = C₂V₂ when making a lower-concentration solution from a known stock, such as preparing a laboratory working solution from a more concentrated solution. It is a conservation relationship: the volume transferred contains a certain amount of solute, and dilution changes the volume and concentration without changing that solute amount.

The equation also works for concentrations stated consistently as mass per volume, such as g/L, or as a percentage, provided the starting and target values use the same basis. Do not mix molarity with mass concentration or mix percentage conventions. A mass/volume percentage and a volume/volume percentage describe different quantities.

This calculator is for general laboratory arithmetic and planning. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

How to Read and Apply the Result

The first result, final solution volume, is the volume the diluted mixture should occupy in total. The second result is the calculated difference between that total and the stock volume transferred. These numbers answer different practical questions: one is the target volume, and the other is the approximate amount of solvent corresponding to that difference.

In accurate solution preparation, the usual approach is to transfer the calculated stock volume and add suitable solvent until the solution reaches the calculated final volume. This distinction matters because volumes may not be perfectly additive: mixing can cause contraction or expansion, and measuring small additions can introduce error. The equation determines the target concentration by amount of solute per final volume, not by a promise that two separately measured liquid volumes add exactly.

Serial Dilutions and Common Errors

A serial dilution uses one dilution as the stock for the next. If each step reduces concentration by a factor of 10, then after three steps the overall reduction is 10 × 10 × 10 = 1,000. For example, a 1 mol/L starting solution would become 0.001 mol/L after three ideal tenfold steps. Each step has its own transfer volume and final volume, and errors can accumulate across steps.

  • Confusing final volume with solvent volume: if the target final volume is 100 mL and the stock portion is 10 mL, the solvent difference is 90 mL—not 100 mL.
  • Mixing units: convert concentrations to a common unit before using the equation. If volumes are entered in different units, convert them too.
  • Rounding too early: keep extra digits during intermediate calculations, then round the final value to a precision supported by the measuring equipment.
  • Trying to dilute upward: a target concentration higher than the stock cannot be achieved by adding solvent. Use a more concentrated starting solution or a different preparation calculation.
  • Assuming the label is exact: stock concentration uncertainty carries through to the diluted result. The equation cannot correct inaccurate source values or measurement error.

Limits and Related Calculations

The equation assumes the solute amount remains constant. It does not account for chemical reactions, precipitation, evaporation, degradation, or a concentration change caused by temperature-dependent volume. If the stock concentration is given as a percentage or as a mass concentration but the target is molarity, first obtain the required molecular mass and any needed density information; those properties depend on the substance and should not be guessed.

When calculating by mass rather than by volume, use a mass-based relationship that matches the concentration definition. For example, mass fraction is solute mass divided by total solution mass, not solution volume. Likewise, a dilution factor is simply C₁/C₂ when concentrations are in matching units; for the example above it is 1/0.1 = 10, a tenfold dilution.

Frequently Asked Questions

What is the formula for dilution?
C₁V₁ = C₂V₂. To calculate final volume, rearrange it to V₂ = C₁V₁/C₂.

How do I calculate how much solvent to add?
Calculate the final volume with C₁V₁/C₂, then subtract the stock volume used: solvent difference = V₂ − V₁. For careful preparation, bring the solution to the final volume rather than relying on exact volume additivity.

Can I use C₁V₁ = C₂V₂ with different concentration units?
Not as written. Convert both concentrations to the same unit and basis first. For example, do not directly pair mol/L with g/L or mix different percentage definitions.

Can dilution make a solution more concentrated?
No. Adding solvent lowers concentration. If C₂ is greater than C₁, this equation yields a final volume smaller than the stock volume, which means the requested change is concentration rather than dilution.

Is the solvent volume always V₂ − V₁?
It is the arithmetic difference between the target total volume and stock volume. In real preparation, liquid volumes may not add exactly, so the reliable target is the final solution volume.

Related

Formula used
in c1 | Stock concentration | mol/L | 1 | 0.000001
in c2 | Target concentration | mol/L | 0.1 | 0.000001
in v1 | Stock volume used | mL | 10 | 0
out vf | Final solution volume | mL | c1 * v1 / c2 | 3
out vs | Solvent to add | mL | c1 * v1 / c2 - v1 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →