molecalculator

Moles & Molar Mass

RCF to G-Force: What the Number Means

Calculator No. 01-2797 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Yes—RCF is g-force expressed as a multiple of standard Earth gravity, so an RCF of 1,000 × g means a radial acceleration 1,000 times standard gravity. This calculator converts between relative centrifugal force (RCF) and rotor speed (RPM) using the rotor radius; enter any two values to calculate the third.

Formula

The calculator uses the standard centrifuge conversion, with radius in centimeters and rotational speed in revolutions per minute:

RCF = 1.118 × 10−5 × r × RPM2

Here, RCF is relative centrifugal force in multiples of standard gravity (× g), r is the distance from the rotation axis to the sample in centimeters, and RPM is revolutions per minute. The calculator’s first output substitutes radius in meters and RPM in thousands: 1.118 × (r / 100) × (RPM / 1000)2. Its other outputs rearrange that equation to solve for RPM or radius.

Standard gravity is exactly 9.80665 m/s2. The underlying centripetal acceleration is a = ω2r, where ω is angular speed in radians per second and r is radius in meters. Dividing acceleration by standard gravity gives RCF. The familiar coefficient 1.118 × 10−5 combines the unit conversions and standard gravity.

Worked Example

Using the calculator’s defaults—radius 10 cm, speed 5,000 RPM, and entered RCF 2,797.92 × g—the headline calculation is:

RCF = 1.118 × (10 / 100) × (5,000 / 1,000)2
= 1.118 × 0.1 × 25
= 2.795 × g
≈ 2,795 × g (rounded to 0 decimal places)

For the RPM output, using the entered RCF of 2,797.92 × g and radius of 10 cm:

RPM = 1,000 × √[2,797.92 / (1.118 × 0.1)]
= 1,000 × √25,026.12
≈ 5,000.61 RPM

For the radius output, using the entered RCF of 2,797.92 × g and speed of 5,000 RPM:

r = 100 × 2,797.92 / [1.118 × (5,000 / 1,000)2]
= 100 × 2,797.92 / 27.95
≈ 10,010.45 cm

The three inputs are independent examples, not a single mutually consistent set: the default radius and speed produce 2,795 × g, while the default RCF is 2,797.92 × g. Enter two mutually consistent measurements to obtain a meaningful third value.

Assumptions

  • The radius is measured from the rotation axis to the sample location, not the rotor’s outside edge.
  • RPM is steady during the calculation; acceleration and deceleration are not represented.
  • RCF is reported relative to standard gravity, 9.80665 m/s2.
  • The model treats the sample as a point at the entered radius. A sample spanning a range of radii experiences a range of RCF values.

Why RCF and g-force Mean the Same Thing Here

“G-force” is an informal name for acceleration described as a multiple of gravitational acceleration. RCF, also called relative centrifugal force, expresses the acceleration due to circular motion in the same way. Thus 500 × g is an acceleration of 500 standard gravities; it is not a force measured in newtons.

In a rotating frame, a sample moves in a circle and continually changes direction. The required inward centripetal acceleration has magnitude ω2r. In the rotating frame, this is often described as an outward centrifugal effect. Centrifuge specifications use RCF as a convenient comparison independent of the machine’s size: the same RPM can produce very different RCFs on rotors with different radii.

The “× g” notation does not mean that the sample’s mass is multiplied by a number of grams. For an object of mass m, the corresponding net force magnitude in an inertial description is ma, measured in newtons. RCF itself is a dimensionless ratio: acceleration divided by standard gravity.

Using RCF and RPM in Practice

RCF is often the more useful setting when a centrifugation method specifies how strongly a sample should be accelerated. RPM is the rotor’s rotational speed. A protocol stated in RPM applies directly only when the rotor geometry matches the method; when rotors differ, matching RCF is generally the relevant comparison, subject to the protocol’s other conditions.

  • Find the rotor radius used by the equipment documentation. A common convention is the distance from the axis to the bottom of the sample or tube position; check which radius the specification uses.
  • Enter radius in centimeters. If you have a radius in millimeters, divide by 10; if in meters, multiply by 100.
  • Enter the RPM or RCF you know. Calculate the missing quantity, then compare the result with the rotor’s stated operating limits and the method’s instructions.
  • Keep units consistent. The coefficient in this calculator assumes centimeters and RPM; inserting millimeters or revolutions per second directly gives a wrong result.

When an RCF value is described as “maximum,” it may refer to the greatest acceleration at the tube bottom rather than at the sample’s midpoint. Because radius varies along a tube, the RCF also varies along it. For critical work, use the precise radius convention specified for that rotor and protocol.

Common Errors and Limits

The most frequent mistake is assuming RPM and RCF are interchangeable. They are related, but conversion requires radius. For example, doubling RPM at fixed radius increases RCF by a factor of four because speed is squared; doubling radius at fixed RPM doubles RCF.

Another source of error is confusing rotor radius with diameter. If the measured quantity is a diameter, halve it before entering it as the radius. A 20 cm diameter corresponds to a 10 cm radius, not a 20 cm radius. Check whether the equipment’s published radius is measured to the tube bottom, sample midpoint, or another reference point.

The calculation describes ideal rotational acceleration, not the complete behavior of a centrifugation process. It does not determine separation efficiency, sedimentation time, heating, vibration, sample compatibility, or safety. Real results also depend on factors such as particle properties, liquid viscosity, rotor design, and the method. Follow the relevant lab method, the safety data sheet (SDS), and your supervisor.

Do not use an RPM calculated from RCF unless the rotor is rated for that speed and the equipment permits it. The rotor’s maximum speed, tube and sample limits, balance requirements, and operating instructions take precedence over a mathematical conversion. A correct RCF calculation does not establish that a particular setup is safe.

Frequently Asked Questions

Is 1,000 RCF the same as 1,000 g?
Yes. In centrifuge notation, 1,000 RCF means an acceleration of 1,000 times standard gravity, written 1,000 × g.

Can I convert RCF to RPM without knowing the radius?
No. The conversion depends on radius as well as RCF. Obtain the correct rotor radius from the rotor documentation or method before calculating.

Does doubling RPM double RCF?
No. At a fixed radius, RCF is proportional to RPM squared. Doubling RPM makes the calculated RCF four times as large.

Is RCF a force in newtons?
No. RCF is a dimensionless acceleration ratio. To express a force in newtons, multiply the acceleration in m/s2 by mass in kilograms.

Which radius should I use for a centrifuge tube?
Use the radius required by the equipment specification or protocol. It may be measured to the sample midpoint or to the tube bottom, and those choices give different RCF values.

Related

Formula used
in r | Rotor radius | cm | 10 | 0
in rpm | Rotor speed | RPM | 5000 | 0
in rcf | Relative centrifugal force | × g | 2797.92 | 0
out rcf | Relative centrifugal force | × g | 1.118 * (r / 100) * (rpm / 1000) ^ 2 | 0
out rpm | Rotor speed | RPM | 1000 * sqrt(rcf / (1.118 * (r / 100))) | 0
out r | Rotor radius | cm | 100 * rcf / (1.118 * (rpm / 1000) ^ 2) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →