molecalculator

Moles & Molar Mass

Electron Configuration A Level Chemistry Explained

Calculator No. 01-9550 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Electron configuration at A level is the arrangement of electrons in an atom’s orbitals, written using the aufbau principle, Hund’s rule, and the Pauli exclusion principle. You enter an element’s atomic number or symbol, and the calculator below generates its ground-state electron configuration in both full and shorthand (noble gas) forms. This is the foundation for explaining periodic trends, bonding, and the chemical properties of elements.

Formula

The electron configuration is built by filling orbitals in order of increasing energy, following the aufbau principle. The order is: 1s, 2s, 2p, 3s, 3p, 4s, 3d, 4p, 5s, 4d, 5p, 6s, 4f, 5d, 6p, 7s, 5f, 6d, 7p. Each orbital holds a maximum of two electrons (Pauli exclusion), and for degenerate orbitals (same energy, like the three 2p orbitals), electrons occupy each orbital singly before pairing (Hund’s rule). The shorthand form uses the preceding noble gas in square brackets, e.g., [Ar] for argon (Z=18), followed by the remaining electrons. The number of unpaired electrons is counted by examining the partially filled subshells.

Worked Example

For iron (Fe, Z = 26):

  1. Fill 1s: 1s2 (2 electrons)
  2. Fill 2s: 2s2 (4 total)
  3. Fill 2p: 2p6 (10 total)
  4. Fill 3s: 3s2 (12 total)
  5. Fill 3p: 3p6 (18 total)
  6. Fill 4s: 4s2 (20 total)
  7. Fill 3d: 3d6 (26 total)

Full configuration: 1s2 2s2 2p6 3s2 3p6 4s2 3d6. Shorthand: [Ar] 3d6 4s2 (note that in shorthand, the 4s comes after 3d, but in the full configuration it is written before 3d because 4s fills first). Unpaired electrons: in the 3d subshell with 6 electrons, Hund’s rule gives 4 unpaired (one pair and four singles).

Assumptions

  • Ground-state (lowest energy) configuration.
  • Gas-phase atoms, not ions or excited states.
  • Standard aufbau order; exceptions for transition metals (e.g., Cr, Cu) are noted but not automatically adjusted.
  • No relativistic effects or orbital contraction considered.

How to Read the Result

The configuration shows the distribution of electrons in shells (n=1,2,3…) and subshells (s, p, d, f). The superscript indicates the number of electrons in that subshell. The shorthand form simplifies writing for elements beyond argon. The unpaired electron count is crucial for predicting magnetic properties (paramagnetic vs. diamagnetic) and the number of bonds an atom can form (valency). For example, iron with 4 unpaired electrons is strongly paramagnetic and commonly forms +2 and +3 oxidation states.

Common Mistakes and Misconceptions

  • 4s vs 3d order: Many students write 3d before 4s in the full configuration, but the aufbau order fills 4s first. However, when writing the shorthand, the 4s is written after 3d because 4s has higher energy than 3d once occupied. This is a common source of confusion.
  • Exceptions: Chromium (Z=24) and copper (Z=29) are exceptions. Cr is [Ar] 3d5 4s1 (not 3d4 4s2) because a half-filled d subshell is more stable. Cu is [Ar] 3d10 4s1 (not 3d9 4s2) due to a fully filled d subshell. The calculator does not apply these exceptions automatically; you should know them for exams.
  • Ions: For cations, electrons are removed from the highest energy orbital first, which is 4s before 3d for transition metals. For example, Fe2+ is [Ar] 3d6, not [Ar] 3d4 4s2.
  • Orbital diagrams: Remember to draw boxes for orbitals and arrows for electrons, with opposite spins in the same box.

Why It Matters for A Level Chemistry

Electron configuration explains the periodic table’s structure: elements in the same group have the same outer shell configuration, leading to similar chemical properties. It also explains trends in atomic radius, ionisation energy, and electronegativity. For example, the increase in ionisation energy across a period is due to increasing nuclear charge with the same outer shell. At A level, you are expected to write configurations for the first 36 elements and for common ions, and to use them to explain periodic trends and bonding.

Limitations of the Aufbau Model

The aufbau principle is a useful guide but not a strict rule. For heavier elements, the energy ordering of orbitals can change due to electron-electron repulsion and relativistic effects. The model also fails to predict the configurations of some transition metals and lanthanides. In reality, the exact configuration is determined by quantum mechanics, but the aufbau model is accurate enough for A level purposes.

Frequently Asked Questions

Why is 4s filled before 3d? In the aufbau order, the 4s orbital has a lower energy than 3d for neutral atoms, so it fills first. However, once both are occupied, the 3d electrons are lower in energy, which is why they are written last in the shorthand and why they are removed first when forming ions.

How do I write the configuration for an ion? For cations, remove electrons from the highest energy orbital first. For transition metals, that means removing 4s electrons before 3d. For anions, add electrons to the next available orbital, following the same order as for neutral atoms.

What are the exceptions to the aufbau principle? The most common exceptions are chromium (Cr) and copper (Cu), where a half-filled or fully filled d subshell is more stable than the predicted configuration. There are others, such as niobium (Nb), molybdenum (Mo), and gold (Au), but they are less commonly tested at A level.

How do I count unpaired electrons? Draw the orbital diagram for the partially filled subshells. Fill each orbital with one electron before pairing. The number of singly occupied orbitals is the number of unpaired electrons.

Is the configuration the same for all isotopes? Yes, isotopes of an element have the same number of electrons and thus the same electron configuration. Only the number of neutrons differs.

Why do some elements have anomalous configurations? The stability of half-filled and fully filled subshells (due to exchange energy and symmetry) can lower the energy enough to promote an electron from a filled s subshell to a d subshell. This is why Cr and Cu behave differently.

Related

Formula used
in z | Atomic number (Z) | - | 26 | 1 | 118
out config | Full electron configuration | - | config | 0
out noble | Noble gas shorthand | - | noble | 0
out unpaired | Unpaired electrons | - | unpaired | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →