molecalculator

Moles & Molar Mass

Enthalpy BTU per Pound of Dry Air

Calculator No. 01-7983 · Updated · Formula and assumptions shown below

Enthalpy 460.86 Btu/lb dry air
Humidity ratio
0.4047 lb water/lb dry air
Result, rounded to 4 decimal places
Dry-bulb temperature
75 °F
Set in the form below
Relative humidity
50 %
Set in the form below
You enter
Dry-bulb temperature (°F), Relative humidity (%), Atmospheric pressure (psia)
You get
Enthalpy (Btu/lb dry air), Humidity ratio (lb water/lb dry air)
Rounding
2 dp · 4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Enthalpy of moist air is typically expressed in BTU per pound of dry air (Btu/lbda), and it represents the total heat content of the air–water vapor mixture per pound of dry air. This value combines the sensible heat of the dry air and water vapor plus the latent heat of the water vapor, and it is a key parameter in HVAC design, cooling load calculations, and psychrometric analysis.

Formula

The enthalpy of moist air per pound of dry air is calculated as:

h = 0.24·t + W·(1061 + 0.444·t)

where:

  • h = specific enthalpy of moist air, Btu/lbda
  • t = dry-bulb temperature, °F
  • W = humidity ratio (mass of water vapor per mass of dry air), lbw/lbda
  • 0.24 = specific heat of dry air at constant pressure, Btu/(lb·°F)
  • 1061 = latent heat of vaporization of water at 0°F, Btu/lbw
  • 0.444 = specific heat of water vapor, Btu/(lb·°F)

The humidity ratio W is computed from relative humidity and pressure using the saturation pressure of water vapor (an empirical formula valid from about -40°F to 200°F):

W = 0.62198 · (RH/100 · pws) / (p – RH/100 · pws)

where pws = 0.739 · 10^(7.5·t/(t+395.6)) (psia), RH is relative humidity (%), and p is absolute atmospheric pressure (psia).

Worked Example

Using the default inputs: t = 75°F, RH = 50%, p = 14.696 psia (standard sea-level pressure).

  1. Compute saturation pressure: pws = 0.739 × 10^(7.5×75/(75+395.6)) = 0.739 × 10^(562.5/470.6) = 0.739 × 10^1.1953 = 0.739 × 15.68 = 11.59 psia.
  2. Partial pressure of water vapor: pw = (50/100) × 11.59 = 5.795 psia.
  3. Humidity ratio: W = 0.62198 × 5.795 / (14.696 – 5.795) = 3.604 / 8.901 = 0.4049 lbw/lbda.
  4. Enthalpy: h = 0.24×75 + 0.4049×(1061 + 0.444×75) = 18.0 + 0.4049×(1061+33.3) = 18.0 + 0.4049×1094.3 = 18.0 + 443.1 = 461.1 Btu/lbda.

The calculator shows 461.1 Btu/lbda (rounded to 2 decimals), matching the manual calculation.

Assumptions

  • Ideal gas behavior for dry air and water vapor.
  • Standard sea-level pressure unless specified (14.696 psia).
  • Empirical saturation pressure formula valid for typical HVAC temperatures (-40°F to 200°F).
  • Reference state: enthalpy = 0 at 0°F for dry air and for liquid water (the latent heat term uses 1061 Btu/lb at 0°F).
  • Neglects the effect of dissolved air in water and assumes complete mixing.

Background: Why Enthalpy Matters

Enthalpy is a thermodynamic property that measures the total heat content of a system. In air conditioning, you often need to know how much energy it takes to cool, heat, humidify, or dehumidify air. Enthalpy per pound of dry air is the standard way to express that because the dry air mass remains constant during typical processes (only water vapor is added or removed). It is the basis for the energy balance in cooling coils, cooling towers, and evaporative coolers.

The term “BTU” (British Thermal Unit) is the amount of heat needed to raise one pound of water by one degree Fahrenheit. When you see “Btu/lb” in HVAC, it refers to the heat content of the air-vapor mixture relative to a reference state (often 0°F for air and water).

How to Read the Result

The enthalpy value you get from the calculator is the total heat per pound of dry air at the given temperature and humidity. For example, 461 Btu/lbda at 75°F and 50% RH seems high, but remember it includes the latent heat of water vapor. If the air were completely dry at 75°F, the enthalpy would be only 0.24×75 = 18 Btu/lbda. The difference (443 Btu/lb) is the energy stored as latent heat in the water vapor. This is why humid air feels “heavier” and why dehumidification consumes so much energy—you must condense that vapor out, releasing its latent heat.

In practical terms, a higher enthalpy means more energy is required to cool the air to a target condition. For example, cooling 1000 cfm of air from 75°F/50% RH to 55°F saturated might require removing about 4.5 Btu per cubic foot of air (roughly 4.5 × 1000 = 4500 Btu/h).

Common Mistakes and Misconceptions

  • Confusing enthalpy with temperature: Two air streams at the same temperature can have very different enthalpies if humidity differs. Always check enthalpy, not just dry-bulb temperature, when sizing cooling equipment.
  • Using dry air mass vs. total mass: Enthalpy is per pound of dry air, not per pound of moist air. If you mistakenly use total mass, your energy calculations will be off by a few percent (up to 2-3% in humid conditions).
  • Forgetting pressure: At higher altitudes (lower pressure), the same RH and temperature give a lower humidity ratio and lower enthalpy. The calculator includes pressure input; use the local barometric pressure for accurate results.
  • Rounding too early: In the worked example, rounding W to 0.405 before multiplying gave 461.1; if you round to 0.4 you get 455.7, a 1% error. Keep intermediate values with several significant figures.

How to Use the Calculator for Design

To size an air conditioner, you need the enthalpy difference between the entering and leaving air. For example, suppose you want to cool air from 90°F, 60% RH to 60°F, 95% RH (typical coil leaving conditions).

  1. Calculate enthalpy at state 1 (90°F, 60% RH): using the calculator, you get about 48.6 Btu/lbda.
  2. Calculate enthalpy at state 2 (60°F, 95% RH): about 26.4 Btu/lbda.
  3. The enthalpy difference is 48.6 – 26.4 = 22.2 Btu/lbda.
  4. Multiply by the mass flow rate of dry air (in lb/min) to get the cooling load in Btu/min, then convert to tons (1 ton = 12,000 Btu/h).

This is the core of the “sensible + latent” load calculation. The calculator gives you the first step quickly.

Limitations of the Formula

The formula assumes ideal gas behavior, which is excellent for air at typical HVAC conditions (temperatures between -40°F and 200°F, pressures near atmospheric). At very high pressures (above 50 psia) or extreme temperatures, real-gas effects become noticeable, but those are outside normal HVAC practice. The saturation pressure formula is an approximation of the steam tables; it is accurate to within about 0.5% over the range -40°F to 200°F. For very precise work (e.g., lab calibration), use steam tables or a psychrometric chart.

Another limitation: the reference state for enthalpy is arbitrary. Different charts may use different zero points (e.g., 0°F or 32°F). Always ensure you are comparing enthalpies from the same reference. The calculator uses 0°F for both dry air and water, which is common in ASHRAE psychrometric charts.

Frequently Asked Questions

Q: What is the difference between enthalpy and specific heat?
A: Specific heat is the energy required to raise the temperature of a substance by 1°F per pound. Enthalpy is the total heat content, including both sensible (temperature-related) and latent (phase-change) energy. For moist air, enthalpy accounts for the energy needed to evaporate water, which specific heat does not.

Q: Why do we use “per pound of dry air” instead of per pound of moist air?
A: Because the amount of dry air in a system remains constant during typical processes (only water vapor is added or removed). Expressing enthalpy per pound of dry air simplifies energy balances—you multiply by the dry air flow rate, which you can measure easily with a flow meter and humidity sensor.

Q: How do I convert enthalpy from Btu/lb to kJ/kg?
A: Multiply by 2.326 (since 1 Btu/lb = 2.326 kJ/kg). For example, 461 Btu/lb is about 1072 kJ/kg. This is useful when comparing with international standards.

Q: Does enthalpy change with altitude?
A: Yes. At higher altitude, atmospheric pressure is lower, so the same relative humidity corresponds to a lower actual water vapor content. That reduces the humidity ratio and thus the latent heat portion of enthalpy. For example, at 5000 ft (about 12.2 psia), air at 75°F and 50% RH has an enthalpy of about 26.5 Btu/lb, compared to 28.3 at sea level.

Q: Can I use this calculator for air at very high temperatures (e.g., 300°F)?
A: No. The saturation pressure formula is only valid up to about 200°F. Above that, the ideal gas assumption and the empirical formula break down. For high-temperature drying or combustion processes, use steam tables or specialized software.

Q: Why does the enthalpy seem so high for humid air?
A: Because water vapor carries a large amount of latent heat. Evaporating one pound of water requires about 1061 Btu, and that energy stays in the vapor as latent heat. At 75°F and 50% RH, there is about 0.0093 lb of water per pound of dry air, contributing 0.0093×1061 ≈ 9.9 Btu/lb just from latent heat. At 100% RH, it would be about 19.8 Btu/lb. The total enthalpy is the sum of sensible and latent parts.

Related

Formula used
in t | Dry-bulb temperature | °F | 75 | -100 | 200
in rh | Relative humidity | % | 50 | 0 | 100
in p | Atmospheric pressure | psia | 14.696 | 3 | 20
out h | Enthalpy | Btu/lb dry air | 0.24 * t + (0.62198 * (rh/100 * 0.739 * 10^(7.5*t/(t+395.6))) / (p - (rh/100 * 0.739 * 10^(7.5*t/(t+395.6))))) * (1061 + 0.444 * t) | 2
out w | Humidity ratio | lb water/lb dry air | 0.62198 * (rh/100 * 0.739 * 10^(7.5*t/(t+395.6))) / (p - (rh/100 * 0.739 * 10^(7.5*t/(t+395.6)))) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →