molecalculator

Moles & Molar Mass

Enthalpy Change A Level Chemistry AQA

Calculator No. 01-8212 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

Enthalpy change (ΔH) in AQA A-level Chemistry is the heat energy transferred at constant pressure, measured in kJ mol⁻¹, with a negative value for exothermic reactions and a positive value for endothermic reactions. You calculate it using calorimetry data (q = mcΔT then divide by moles) or by applying Hess’s Law with known enthalpy values. This page explains the definitions, the calculations, and the common pitfalls so you can apply them confidently in exams.

Formula

For a reaction in solution, the heat energy transferred is:

q = m × c × ΔT

  • q = heat energy absorbed or released (J)
  • m = mass of the solution (usually water) in grams (g)
  • c = specific heat capacity of the solution (J g⁻¹ K⁻¹); for dilute aqueous solutions, use 4.18 J g⁻¹ K⁻¹
  • ΔT = temperature change in kelvin (K); a 1 °C change equals a 1 K change

Then divide by the number of moles of the substance whose enthalpy change you are measuring:

ΔH = (q / 1000) / n

where n is in moles and the factor 1000 converts joules to kilojoules. The sign of ΔT determines the sign of ΔH: a temperature rise (exothermic) gives a negative ΔH; a temperature fall (endothermic) gives a positive ΔH.

Worked Example

Using the defaults from the calculator: 100 g of water, c = 4.18 J g⁻¹ K⁻¹, ΔT = +12.5 K, and n = 0.025 mol of the limiting reactant.

  1. Calculate q: q = 100 × 4.18 × 12.5 = 5225 J
  2. Convert to kJ: 5225 J = 5.225 kJ
  3. Divide by moles: ΔH = 5.225 / 0.025 = 209 kJ mol⁻¹

Because the temperature increased, the reaction is exothermic, so ΔH = −209 kJ mol⁻¹ (the calculator shows the magnitude; you must assign the sign based on the temperature change).

Assumptions

  • The specific heat capacity of the solution equals that of pure water (4.18 J g⁻¹ K⁻¹).
  • The density of the solution is 1.00 g mL⁻¹, so the mass of solution equals its volume in grams.
  • No heat is lost to the surroundings (the calorimeter is perfectly insulated).
  • The reaction goes to completion and the limiting reactant is fully consumed.
  • For Hess’s Law calculations, all enthalpy values are at the same conditions (usually 298 K and 1 atm).

Standard Enthalpy Changes You Must Know

AQA defines several standard enthalpy changes (all with the standard symbol ΔH°). These are the ones you will be asked to define or use:

  • Enthalpy of formation (ΔHf°): enthalpy change when one mole of a compound is formed from its elements in their standard states under standard conditions.
  • Enthalpy of combustion (ΔHc°): enthalpy change when one mole of a substance is completely burned in oxygen under standard conditions.
  • Enthalpy of neutralisation (ΔHn°): enthalpy change when one mole of water is formed from an acid–base reaction under standard conditions.
  • Enthalpy of atomisation (ΔHat°): enthalpy change when one mole of gaseous atoms is formed from the element in its standard state.
  • Ionisation energy and electron affinity (used in Born–Haber cycles).
  • Lattice enthalpy (formation of one mole of ionic lattice from gaseous ions).

Standard conditions are 298 K (25 °C), 100 kPa pressure, and 1 mol dm⁻³ solutions where relevant.

How to Calculate ΔH Using Calorimetry

The experimental method (used in required practical 2) involves measuring the temperature change of a known mass of water when a known amount of substance reacts or dissolves.

  1. Measure the volume of solution (assume density = 1 g mL⁻¹ to get mass).
  2. Record the initial temperature, then add the reactant and record the maximum or minimum temperature.
  3. Calculate ΔT (final − initial).
  4. Use q = mcΔT to find the heat absorbed by the water.
  5. Calculate the moles of the substance (n = mass / Mr, or n = concentration × volume).
  6. Divide q (in kJ) by n to get ΔH in kJ mol⁻¹.
  7. Add the sign: negative if temperature rose, positive if it fell.

For combustion experiments, you burn a known mass of fuel and heat a known mass of water; the same formula applies, but you must account for the mass of fuel burned (ΔH = q / moles of fuel).

Hess’s Law and Energy Cycles

Hess’s Law states that the enthalpy change for a reaction is independent of the route taken. This lets you calculate ΔH for reactions that are difficult to measure directly. In AQA, you will use two main types of cycles:

  • Formation cycles: ΔHr° = ΣΔHf°(products) − ΣΔHf°(reactants)
  • Combustion cycles: ΔHr° = ΣΔHc°(reactants) − ΣΔHc°(products)

For example, to find the enthalpy of formation of propane (C₃H₈), you can use the combustion enthalpies of carbon, hydrogen, and propane:

ΔHf°(C₃H₈) = 3ΔHc°(C) + 4ΔHc°(H₂) − ΔHc°(C₃H₈)

Always draw the cycle and label the arrows: formation arrows point up, combustion arrows point down. Then apply the rule: products minus reactants for formation, reactants minus products for combustion.

Common Mistakes and Exam Tips

  • Sign errors: The biggest source of lost marks. Always state whether the reaction is exothermic (negative) or endothermic (positive) based on the temperature change.
  • Units: q is in joules, but ΔH is in kJ mol⁻¹. Forgetting to divide by 1000 is a classic error.
  • Mass vs. volume: In solution calorimetry, use the total mass of the solution, not just the mass of the solute. Assume 1 cm³ ≈ 1 g.
  • Moles: Use the moles of the substance that limits the reaction, not the one in excess. For neutralisation, use the moles of water formed.
  • ΔT in kelvin: A temperature change in °C is numerically the same in K, but you must write the unit as K in your final answer.
  • Hess’s Law direction: When reversing an equation, flip the sign of ΔH. When multiplying an equation, multiply ΔH by the same factor.
  • Bond enthalpy vs. enthalpy of formation: Bond enthalpies are average values and always positive; ΔHf° can be negative or positive.

Limitations of Calorimetry

Experimental values are always less negative than theoretical ones because heat is lost to the surroundings, the calorimeter absorbs heat, and combustion may be incomplete. In exams, you may be asked to suggest improvements: insulate the container, use a lid, stir continuously, use a more precise thermometer, or use a bomb calorimeter for combustion. Also, the specific heat capacity of the solution may differ from water, and the density assumption may not hold for concentrated solutions.

Frequently Asked Questions

What is the difference between ΔH and ΔH°?

ΔH is the enthalpy change under the actual conditions of the experiment. ΔH° (with a plimsoll symbol) is the standard enthalpy change measured under standard conditions (298 K, 100 kPa, 1 mol dm⁻³ solutions). In AQA, you usually calculate ΔH° using Hess’s Law, while experimental calorimetry gives ΔH (which you may compare to the standard value, noting the differences).

Why is ΔH negative for exothermic reactions?

In an exothermic reaction, the system loses heat to the surroundings, so the final enthalpy of the products is lower than that of the reactants. Enthalpy change is defined as products minus reactants, so a lower product enthalpy gives a negative value. The surroundings gain heat, which is why the temperature rises.

How do I know which sign to use in Hess’s Law?

Use the rule: for formation cycles, ΔHr = ΣΔHf(products) − ΣΔHf(reactants). For combustion cycles, it is the reverse: ΔHr = ΣΔHc(reactants) − ΣΔHc(products). Draw the cycle and check the direction of the arrows: if you go against an arrow, you subtract that value.

What is a Born–Haber cycle?

It is a specific Hess’s Law cycle used to calculate lattice enthalpy for ionic compounds. It involves steps like atomisation, ionisation, electron affinity, and formation. AQA requires you to interpret and use Born–Haber cycles, not necessarily construct them from scratch, but you should be able to label each step and calculate the unknown value.

Why do my experimental values differ from data book values?

Heat loss to the surroundings is the main reason. Incomplete combustion, non-standard conditions, and the assumption that the solution has the same density and specific heat as water also contribute. These factors make experimental ΔH values less exothermic (less negative) than theoretical values.

When should I use bond enthalpies instead of formation enthalpies?

Bond enthalpies are useful for reactions where no formation data is available, but they are average values from many compounds, so they give less accurate results. Formation enthalpies are more accurate because they refer to specific compounds. In AQA, you may be asked to calculate ΔH using mean bond enthalpies, but you should note that the answer is approximate.

Related

Formula used
in m | Mass of water (m) | g | 100 | 0
in c | Specific heat capacity of water (c) | J/g·K | 4.18 | 0
in dt | Temperature change (ΔT) | K | 12.5 | -273.15
in n | Moles of limiting reactant | mol | 0.025 | 0
out q | Heat energy (q) | J | m * c * dt | 1
out dH | Enthalpy change (ΔH) | kJ/mol | (q / 1000) / n | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →