The specific enthalpy of dry air is the total heat content per unit mass of dry air, measured relative to a reference state (typically 0 °C), and at 25 °C (298.15 K) it is approximately 25,110 J/kg or 25.11 kJ/kg. This calculator computes the specific enthalpy of dry air using the common linear formula h = cp · T, where cp is the specific heat at constant pressure (about 1005 J/(kg·K) for dry air) and T is the absolute temperature in kelvin. Enter the air temperature in °C (or any temperature scale you convert) and the calculator returns the specific enthalpy in J/kg and kJ/kg.
Formula
The specific enthalpy of dry air is calculated using the sensible heat equation:
h = cp × T
Where:
- h = specific enthalpy (J/kg)
- cp = specific heat capacity of dry air at constant pressure = 1005 J/(kg·K) (at typical atmospheric temperatures, 0–40 °C)
- T = absolute temperature in kelvin (K) = temperature in °C + 273.15
This formula assumes dry air behaves as an ideal gas and that cp is constant over the temperature range. For more precise work at high temperatures (above 100 °C) or very low temperatures, cp varies slightly, but the error is less than 1% for most HVAC and meteorological applications.
Worked Example
Using the default input of 25 °C:
- Convert temperature to kelvin: T = 25 + 273.15 = 298.15 K
- Apply the formula: h = 1005 J/(kg·K) × 298.15 K = 299,640.75 J/kg
- Convert to kJ/kg: 299,640.75 / 1000 = 299.64 kJ/kg
The calculator shows 299,641 J/kg and 299.64 kJ/kg. Note that this is the enthalpy relative to 0 K (absolute zero). In engineering practice, enthalpy is often referenced to 0 °C, so the value would be 1005 × 25 = 25,125 J/kg. The calculator uses the absolute reference, but you can subtract 273.15 × 1005 = 274,515.75 J/kg to get the 0 °C reference value.
Assumptions
- Dry air is treated as an ideal gas (compressibility factor ≈ 1 at atmospheric pressure).
- The specific heat capacity cp is constant at 1005 J/(kg·K) over the temperature range –50 °C to 100 °C.
- No moisture (water vapor) is present; for humid air, the enthalpy includes a term for water vapor.
- The reference state for enthalpy is absolute zero (0 K). Many textbooks use 0 °C as the reference; the difference is a constant offset.
Why Specific Enthalpy Matters
Specific enthalpy is a fundamental property in thermodynamics used to quantify the energy content of air in heating, ventilation, air conditioning (HVAC), and meteorology. It tells you how much heat energy is stored in each kilogram of dry air. This is essential for:
- Designing air heating and cooling systems – the enthalpy change determines the heating or cooling load.
- Calculating energy consumption in drying processes, where air absorbs moisture and heat.
- Understanding atmospheric energy transport – enthalpy differences drive weather systems.
- Psychrometrics – the study of moist air properties, where dry air enthalpy is a baseline.
When you know the mass flow rate of air (kg/s), multiplying by the specific enthalpy gives the total energy flow (watts). This is how engineers size coils, ducts, and compressors.
How to Read the Result
The calculator returns specific enthalpy in J/kg and kJ/kg. A typical room at 25 °C has an enthalpy of about 299.6 kJ/kg (relative to 0 K). If you compare two states, the difference in specific enthalpy (Δh) tells you the heat added or removed per kilogram of air. For example, heating air from 20 °C to 30 °C:
- h(30°C) = 1005 × 303.15 = 304,665.75 J/kg
- h(20°C) = 1005 × 293.15 = 294,615.75 J/kg
- Δh = 10,050 J/kg = 10.05 kJ/kg
This matches the simple calculation: 1005 × 10 = 10,050 J/kg. The offset from absolute zero cancels, so for temperature differences, the reference doesn’t matter.
Common Mistakes and Misconceptions
One common mistake is using °C directly in the formula without converting to kelvin. Since cp has units J/(kg·K), the temperature must be in kelvin. If you use °C, you get a value that is off by 273.15 × 1005 ≈ 274,516 J/kg – a huge error. Another mistake is confusing specific enthalpy (per kg) with total enthalpy (per mass flow). Always multiply by mass flow rate to get energy rate.
A frequent misconception is that specific enthalpy of dry air is zero at 0 °C. In this calculator, it’s not – it’s about 274.5 kJ/kg relative to absolute zero. In many engineering charts, however, the reference is 0 °C, so the enthalpy at 0 °C is defined as 0 kJ/kg. Both are valid; the difference is a constant offset. When you read enthalpy values from different sources, check the reference state.
Also, this calculator is for dry air. Humid air has additional enthalpy from water vapor. The total enthalpy of moist air is approximately hmoist = hdry + ω × hvapor, where ω is the humidity ratio (kg water per kg dry air) and hvapor is the enthalpy of water vapor (about 2501 kJ/kg plus 1.86 × T). For typical indoor air with ω ≈ 0.01, the vapor contribution is about 25 kJ/kg, which is significant.
Limits of the Formula
The linear formula h = cpT is accurate for temperatures between –50 °C and 100 °C at atmospheric pressure. Outside this range, cp changes: at 200 °C, it’s about 1020 J/(kg·K); at 500 °C, about 1090 J/(kg·K). For cryogenic or high-temperature applications, use property tables or more complex equations of state. Also, at very high pressures (above 10 atm), the ideal gas assumption fails, and enthalpy depends on pressure as well as temperature.
For most HVAC and environmental calculations, the constant cp is sufficient. The calculator allows temperatures up to 2000 °C, but the result beyond 100 °C should be treated as an approximation with increasing error.
Frequently Asked Questions
What is the difference between specific enthalpy and specific internal energy?
Enthalpy (h) is defined as h = u + pv, where u is internal energy, p is pressure, and v is specific volume. For a constant-pressure process, the change in enthalpy equals the heat added. Internal energy is the total kinetic and potential energy of molecules; enthalpy adds the work done to push the air against the atmosphere. For dry air, the difference is pv = RT (for ideal gas), which is about 8.314/0.02897 × T ≈ 287 × T J/kg. At 25 °C, that’s about 85.6 kJ/kg. So enthalpy is always larger than internal energy.
Why do some tables show enthalpy of dry air as 0 at 0 °C?
Because they use a different reference state. In many engineering textbooks, the reference is 0 °C (273.15 K), and enthalpy is defined as zero at that temperature. This is convenient because you only care about differences. The calculator uses absolute zero as reference, so you get a large positive number. To convert to the 0 °C reference, subtract 274,515.75 J/kg (which is 1005 × 273.15). The difference between two states is identical regardless of reference.
How do I calculate the enthalpy of humid air?
For moist air, you need the humidity ratio (ω) in kg water vapor per kg dry air. The specific enthalpy of moist air is: h_moist = h_dry + ω × h_vapor, where h_vapor ≈ 2501 + 1.86 × T (kJ/kg) at temperature T in °C. For example, at 25 °C and 50% relative humidity, ω ≈ 0.0099 kg/kg, so h_vapor ≈ 2501 + 1.86×25 = 2547.5 kJ/kg. Then h_moist = 299.64 + 0.0099 × 2547.5 ≈ 324.9 kJ/kg (relative to absolute zero). For precise work, use a psychrometric chart.
Does the specific enthalpy of dry air depend on pressure?
For an ideal gas, enthalpy depends only on temperature, not pressure. Dry air at 1 atm and 2 atm at the same temperature has the same specific enthalpy. In reality, air is not perfectly ideal, but the effect of pressure is negligible for pressures up to a few atmospheres. This is why the calculator only asks for temperature.
What is the specific heat capacity of dry air exactly?
The specific heat at constant pressure (c_p) for dry air is approximately 1005 J/(kg·K) at 25 °C. More precisely, it varies slightly with temperature: 1004 J/(kg·K) at 0 °C, 1005 at 25 °C, 1007 at 50 °C, and 1010 at 100 °C. The value 1005 is a standard engineering approximation. For most calculations, the variation is less than 0.5%.
Can I use this calculator for air at high altitudes?
Yes, because enthalpy is independent of pressure for an ideal gas. At high altitudes, the temperature is lower, so you enter the actual temperature. For example, at 3000 m altitude, the standard temperature is about –4.5 °C, so h = 1005 × (268.65) ≈ 269,993 J/kg. The lower temperature means less enthalpy, which is why air at altitude feels colder.
Related
Formula used
in t | Air temperature | °C | 25 | -273.15 | 2000 out h | Specific enthalpy | J/kg | 1005 * (t + 273.15) | 0 out hk | Specific enthalpy | kJ/kg | h / 1000 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Normality to g/L Converter & Formula29.220 g/L
- Normality to meq/mL Conversion Calculator1.0000 meq/mL
- Normality Test Q-Q Plot: How to Read It
- Normality Test Results: How to Analyze Them
- Normality Slay the Spire?
- Normality Test for Paired t Test: How to Check