molecalculator

Moles & Molar Mass

Enthalpy Change Formula A Level Chemistry

Calculator No. 01-7804 · Updated · Formula and assumptions shown below

The calculator on this page is switched off while it is checked. The formula is below, and the worked example shows how to do the sum by hand.

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The enthalpy change formula in A Level Chemistry is ΔH = Hproducts − Hreactants, where ΔH is the heat change at constant pressure. In practice, you calculate it using ΔH = −mcΔT / n for calorimetry experiments, or ΔH = Σ(bond enthalpies of reactants) − Σ(bond enthalpies of products) for bond energy calculations.

Formula

The most common enthalpy change formula in A Level Chemistry is the calorimetry equation:

ΔH = −mcΔT / n

Where:

  • ΔH = enthalpy change in kJ/mol (negative for exothermic, positive for endothermic)
  • m = mass of the solution or water in grams (g)
  • c = specific heat capacity of the solution in J/g·K (for water, 4.18 J/g·K)
  • ΔT = temperature change in °C or K (the numerical value is the same in both)
  • n = moles of the limiting reactant (the substance you are measuring the enthalpy change per mole of)

The negative sign is crucial: it converts the heat absorbed by the solution (q) into the heat released by the reaction. If the temperature rises, ΔT is positive, q is positive, and ΔH becomes negative—indicating an exothermic reaction.

For bond enthalpy calculations, the formula is:

ΔH = Σ(bond enthalpies of reactants) − Σ(bond enthalpies of products)

This uses mean bond enthalpies (average values for a bond in many compounds) and works only for gaseous molecules.

Worked Example

Using the calculator defaults: 100 g of water, specific heat capacity 4.18 J/g·K, temperature rise of 8.5 °C, and 0.025 mol of limiting reactant.

Step 1: Calculate the heat absorbed by the water:

q = m × c × ΔT = 100 × 4.18 × 8.5 = 3553 J

Step 2: Convert to kJ: 3553 J = 3.553 kJ

Step 3: Divide by moles and apply the negative sign:

ΔH = −3.553 kJ / 0.025 mol = −142.1 kJ/mol

The calculator gives ΔH = −142.12 kJ/mol (rounded to 2 decimal places). The slight difference is due to rounding in the intermediate step.

Assumptions

  • The specific heat capacity of the solution equals that of pure water (4.18 J/g·K). This is only true for dilute aqueous solutions.
  • The density of the solution is 1 g/mL, so the mass of the solution equals its volume in mL.
  • No heat is lost to the surroundings (perfect insulation).
  • The thermometer and container absorb negligible heat.
  • The reaction goes to completion and the limiting reactant is fully consumed.
  • For bond enthalpy calculations, all reactants and products are in the gaseous state.

Why the Sign Matters

The negative sign in ΔH = −mcΔT/n is the most common source of error. When a reaction releases heat (exothermic), the solution warms up, so ΔT is positive. The equation then gives a negative ΔH, which is correct. For an endothermic reaction (e.g., dissolving ammonium nitrate), the solution cools, ΔT is negative, and ΔH becomes positive.

In A Level exams, you must state whether a reaction is exothermic or endothermic based on the sign. A negative ΔH means the products have less chemical energy than the reactants; the difference is released as heat. A positive ΔH means the products have more energy; the difference is absorbed from the surroundings.

Common Mistakes and How to Avoid Them

  • Forgetting the negative sign – Always include it in the formula. If you get a positive ΔH for a combustion reaction, you have missed it.
  • Using the wrong mass – For reactions in solution, use the total mass of the solution (usually the combined volumes of reactants, assuming density = 1 g/mL). Do not include the mass of any solid added if it dissolves completely.
  • Mixing up °C and K – Temperature changes (ΔT) are the same in both scales, but absolute temperatures are not. Always use ΔT, not the final temperature.
  • Forgetting to convert J to kJ – ΔH is usually quoted in kJ/mol, but q is in J. Divide by 1000 before dividing by moles.
  • Using the wrong moles – Use the moles of the substance that is fully consumed (limiting reactant), not the one in excess. For combustion, use the moles of the fuel burned.
  • Rounding too early – Keep intermediate values to at least 3 significant figures, then round the final answer to the appropriate precision (usually 3 sig figs).

Bond Enthalpy vs. Calorimetry

There are two main ways to calculate ΔH in A Level Chemistry, and they give different results. Calorimetry measures the actual heat change in a real reaction, including any heat loss. Bond enthalpy calculations use average bond energies from many compounds, so they are theoretical and often differ from experimental values by 5–10%.

Bond enthalpies are always positive (energy is needed to break bonds). The formula ΔH = Σ(bonds broken) − Σ(bonds formed) works because breaking bonds requires energy (positive) and forming bonds releases energy (negative). If the energy released forming new bonds is greater than the energy needed to break old bonds, the reaction is exothermic.

For example, in the combustion of methane (CH₄ + 2O₂ → CO₂ + 2H₂O), you break 4 C–H bonds and 2 O=O bonds, and form 2 C=O bonds and 4 O–H bonds. Using mean bond enthalpies, the calculation gives approximately −800 kJ/mol, while the experimental enthalpy of combustion is about −890 kJ/mol. The difference comes from the mean bond enthalpy values and the assumption that all species are gaseous (water is actually liquid in the standard enthalpy change).

Hess’s Law and Enthalpy Cycles

Another way to find ΔH is through Hess’s Law, which states that the total enthalpy change for a reaction is independent of the route taken. This is useful when a reaction is difficult to measure directly (e.g., formation of carbon monoxide from carbon and oxygen, which also produces CO₂).

The formula is: ΔHreaction = ΣΔHf(products) − ΣΔHf(reactants), where ΔHf is the standard enthalpy of formation.

In A Level exams, you may be asked to construct an enthalpy cycle using formation enthalpies or combustion enthalpies. The key is to draw the cycle correctly and then apply the formula: the sum of the enthalpy changes around a closed loop is zero.

Limitations of the Formula

The calorimetry formula assumes perfect insulation and negligible heat capacity of the container. In reality, heat is always lost to the surroundings, so the measured temperature change is smaller than the true value. This makes experimental ΔH values less exothermic (or less endothermic) than the theoretical values.

The formula also assumes the specific heat capacity of the solution is constant over the temperature range, which is approximately true for dilute solutions but not for concentrated ones or non-aqueous solvents.

For bond enthalpies, the values are averages across many compounds, not exact for a specific molecule. For example, the C–H bond enthalpy varies slightly depending on the molecule (methane vs. ethane), but a single mean value is used. This limits accuracy.

Finally, the formula only applies to constant pressure conditions. At constant volume, the heat change is the internal energy change (ΔU), not enthalpy. In A Level experiments, reactions are usually done in open containers at atmospheric pressure, so the constant pressure assumption holds.

Frequently Asked Questions

What is the difference between ΔH and q?

q is the heat energy transferred to or from the surroundings (measured in J or kJ). ΔH is the enthalpy change per mole of a substance (measured in kJ/mol). In calorimetry, you first calculate q using q = mcΔT, then divide by the number of moles to get ΔH. The negative sign converts the heat gained by the solution into the heat lost by the reaction.

Why do I need to divide by moles?

Enthalpy change is an intensive property—it depends on the amount of substance. Dividing by moles standardizes the value so you can compare reactions that use different quantities. For example, burning 1 g of methane gives a certain heat, but the enthalpy of combustion is quoted per mole of methane, allowing comparison with other fuels.

When should I use ΔH = −mcΔT/n vs. bond enthalpies?

Use ΔH = −mcΔT/n when you have experimental data from a calorimetry experiment (mass, temperature change, moles). Use bond enthalpies when you are given a chemical equation and a table of mean bond enthalpies, and you need to estimate the enthalpy change theoretically. The calorimetry method gives a real measured value; the bond method gives an approximate calculated value.

Why is my experimental ΔH less exothermic than the data book value?

Heat loss to the surroundings is the main reason. The calorimeter is not perfectly insulated, so some heat escapes before the maximum temperature is recorded. Also, the thermometer and container absorb some heat, and the reaction may not go to completion. These factors reduce the measured temperature change, leading to a smaller (less negative) ΔH.

Do I use the mass of the solution or the mass of the reactants?

Use the mass of the solution (the water or solvent plus any dissolved solute). For reactions in aqueous solution, this is usually the total volume of the solutions mixed, assuming a density of 1 g/mL. Do not include the mass of a solid reactant that is added in excess, because it does not contribute to the heat capacity of the solution.

Can ΔH be positive for a reaction that feels hot?

No. If a reaction feels hot, it is releasing heat to the surroundings, so the temperature of the solution rises, ΔT is positive, and ΔH is negative (exothermic). A positive ΔH means the reaction absorbs heat, so the solution cools down (endothermic). The sign of ΔH always matches the direction of heat flow relative to the system.

Related

Formula used
in m | Mass of solution | g | 100 | 0
in c | Specific heat capacity | J/g·K | 4.18 | 0
in dT | Temperature change | °C | 8.5 | -273.15
in n | Moles of limiting reactant | mol | 0.025 | 0
out q | Heat energy change (q) | J | m * c * dT | 1
out dh | Enthalpy change (ΔH) | kJ/mol | -q / (n * 1000) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →