molecalculator

Moles & Molar Mass

Enthalpy Change of Solution Equation

Calculator No. 01-9234 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The enthalpy change of solution (ΔHsol) is the heat absorbed or released when one mole of a solute dissolves in a solvent at constant pressure. The equation is ΔHsol = q / n, where q is the heat exchanged (in joules or kilojoules) and n is the amount of solute dissolved (in moles). This calculator computes ΔHsol from the mass of solute, its molar mass, the final solution volume, and the measured temperature change of the solution.

Formula

The enthalpy change of solution is defined by the equation:

ΔHsol = q / n

where:

  • ΔHsol = enthalpy change of solution (kJ/mol or J/mol)
  • q = heat absorbed or released by the solution (J or kJ)
  • n = amount of solute dissolved (mol)

For a constant-pressure calorimeter, q is calculated from the temperature change of the solution:

q = msolution × cp × ΔT

where msolution is the mass of the solution (g), cp is the specific heat capacity of the solution (J/g·°C), and ΔT is the temperature change (°C). For dilute aqueous solutions, we assume msolution ≈ volume (mL) × 1.00 g/mL and cp ≈ 4.18 J/g·°C.

To find n, you need the molar mass of the solute (g/mol) and the mass used:

n = msolute / M

This calculator computes the molarity (c) and millimolar concentration (cmm) of the resulting solution, which are often used to report the concentration when studying enthalpy of solution. To get ΔHsol itself, you would also enter the temperature change and solution mass in a calorimetry calculation.

Worked Example

Suppose you dissolve 2.922 g of sodium chloride (NaCl, molar mass 58.44 g/mol) in enough water to make 250 mL of solution. Using the default values in the calculator:

  1. Calculate moles of solute: n = 2.922 g / 58.44 g/mol = 0.05000 mol
  2. Convert volume to liters: V = 250 mL / 1000 = 0.250 L
  3. Calculate molarity: c = n / V = 0.05000 mol / 0.250 L = 0.2000 mol/L
  4. The calculator shows c = 0.2000 mol/L and cmm = 200.0 mM

If this dissolution caused a temperature drop of 0.50 °C in 250 g of solution, the heat absorbed would be q = 250 g × 4.18 J/g·°C × 0.50 °C = 522.5 J. Then ΔHsol = 522.5 J / 0.0500 mol = 10450 J/mol = 10.45 kJ/mol (positive, endothermic).

Assumptions

  • The solution is dilute enough that the specific heat capacity is close to that of pure water (4.18 J/g·°C).
  • The density of the solution is approximately 1.00 g/mL, so the mass of solution equals the volume in mL.
  • The calorimeter absorbs no heat and no heat is lost to the surroundings.
  • The solute is fully dissolved and the final volume is used, not the volume of solvent added.
  • Pressure is constant (usually 1 atm).

How to Use the Calculator

This calculator is designed for lab planning and study. Enter the mass of solute, its molar mass, and the final solution volume. The calculator returns the molar concentration and millimolar concentration. To compute the enthalpy change of solution, you must also know the temperature change and the mass of the solution, which you can measure in a calorimetry experiment.

For example, if you are preparing a 0.200 M NaCl solution, you can use the calculator to verify your mass and volume. For enthalpy studies, you would measure the temperature change with a thermometer or temperature probe and then apply the formula.

Common Mistakes

  • Using the volume of solvent instead of the final solution volume. Always use the final volume after dissolution.
  • Forgetting to convert mL to L in molarity calculations. Divide by 1000.
  • Confusing the sign of ΔH. A positive ΔH means endothermic (solution cools), a negative ΔH means exothermic (solution warms).
  • Assuming the specific heat of the solution is exactly that of water even for concentrated solutions. For most school experiments, this is acceptable.
  • Not accounting for the heat capacity of the calorimeter. For precise work, include it.

Why Enthalpy of Solution Matters

The enthalpy change of solution tells you whether dissolving a substance absorbs or releases heat. This is critical in many real-world applications: instant cold packs use endothermic dissolutions (e.g., ammonium nitrate), while hot packs use exothermic ones (e.g., calcium chloride). In the lab, knowing ΔHsol helps predict temperature changes when preparing solutions, which can affect reaction rates and solubility.

The overall enthalpy of solution is the sum of two contributions: the energy required to break the solute-solute and solvent-solvent interactions (endothermic) and the energy released when new solute-solvent interactions form (exothermic). The net effect determines the sign and magnitude of ΔHsol.

Limitations of the Formula

The simple equation ΔHsol = q/n assumes ideal behavior: no heat loss, constant pressure, and complete dissolution. Real solutions may deviate, especially at high concentrations. Also, the enthalpy of solution can depend on the final concentration; the value for an infinitely dilute solution (ΔHsol° ) is often reported. For ionic compounds, the lattice energy and hydration energy are large, so the net ΔHsol can be small but measurable.

This calculator only computes concentration; it does not calculate ΔHsol directly because that requires the temperature change, which is an experimental input. Use the formula with your measured q and n.

Frequently Asked Questions

What is the difference between enthalpy of solution and enthalpy of hydration?

Enthalpy of solution is the total heat change when a solute dissolves in a solvent. Enthalpy of hydration is the heat change when gaseous ions (or molecules) are surrounded by water molecules. The relationship is: ΔHsol = ΔHlattice + ΔHhydration, where ΔHlattice is the lattice energy (endothermic) and ΔHhydration is usually exothermic.

Why is the enthalpy of solution sometimes positive and sometimes negative?

It depends on the balance between breaking existing interactions (endothermic) and forming new solute-solvent interactions (exothermic). For example, ammonium nitrate dissolving in water is endothermic (positive ΔH), while sodium hydroxide dissolving is exothermic (negative ΔH).

How do I measure the enthalpy change of solution in the lab?

Use a calorimeter: dissolve a known mass of solute in a known volume of water, measure the temperature change, calculate q using q = mcΔT, then divide by the moles of solute. Ensure you account for the calorimeter’s heat capacity if needed.

Does the enthalpy of solution depend on the amount of solvent?

Yes, the enthalpy of solution can vary with concentration. For dilute solutions, it approaches a limiting value (ΔHsol°). For concentrated solutions, interactions between solute particles become significant, so the value changes.

What is the unit of enthalpy change of solution?

The SI unit is joules per mole (J/mol) or kilojoules per mole (kJ/mol). In some contexts, you may see calories per mole (cal/mol); 1 cal = 4.184 J.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →