molecalculator

Moles & Molar Mass

Diesel Enthalpy of Combustion: MJ/kg & BTU/gal

Calculator No. 01-9797 · Updated · Formula and assumptions shown below

Lower heating value (mass) 44.80 MJ/kg
Lower heating value (volume)
37.27 MJ/L
= 44.8 × Density of diesel
Energy (BTU)
42,462 BTU
= (Mass of diesel × 44.8 × 947.817)
Mass of diesel
1 kg
Set in the form below
You enter
Mass of diesel (kg), Volume of diesel (L), Density of diesel (kg/L)
You get
Lower heating value (mass) (MJ/kg), Lower heating value (volume) (MJ/L), Energy (BTU) (BTU)
Rounding
2 dp · 0 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The enthalpy of combustion of diesel fuel is approximately 44.8 megajoules per kilogram (MJ/kg) on a lower heating value (LHV) basis, which equals about 38.6 MJ per liter or 138,700 BTU per US gallon. This is the heat released when diesel burns completely with oxygen at constant pressure, with water leaving as vapor (LHV); the higher heating value (HHV), where water condenses, is about 45.6 MJ/kg.

Formula

The enthalpy of combustion is the energy released per unit mass or volume of fuel. For diesel, the standard values are:

  • LHV (mass): 44.8 MJ/kg (this is the default and is used in the calculator).
  • LHV (volume): LHV_mass × density (in kg/L). With density 0.832 kg/L, that gives 37.3 MJ/L.
  • Energy in BTU: Energy (MJ) × 947.817 BTU/MJ.

Where:

  • m = mass of diesel in kg
  • v = volume of diesel in liters (used only for reference; the calculator uses mass for energy)
  • density = density of diesel in kg/L (typical range 0.82–0.85, default 0.832)
  • LHV_mass = lower heating value per kg (44.8 MJ/kg)

The calculator computes the total energy released for a given mass, and also shows the volumetric energy density using the density you enter.

Worked Example

Using the default inputs: mass = 1 kg, volume = 1 L, density = 0.832 kg/L.

  1. LHV_mass = 44.8 MJ/kg (given).
  2. LHV_volume = 44.8 × 0.832 = 37.27 MJ/L (rounded to 37.27).
  3. Energy in BTU = (1 kg × 44.8 MJ/kg) × 947.817 BTU/MJ = 42,462 BTU (rounded to 42,462).

The calculator shows: LHV mass = 44.80 MJ/kg, LHV volume = 37.27 MJ/L, Energy = 42,462 BTU.

Assumptions

  • Diesel is represented by the average formula C₁₂H₂₃ (a common approximation).
  • Combustion is complete (all carbon to CO₂, all hydrogen to H₂O).
  • Lower heating value assumes water leaves as vapor; higher heating value assumes liquid water.
  • Density is an input because it varies with temperature and blend; the default 0.832 kg/L is typical at 15 °C.
  • The enthalpy of combustion is taken as a constant 44.8 MJ/kg; real diesel varies slightly (44.4–45.0 MJ/kg) depending on composition.

What Is Diesel Fuel?

Diesel is a middle distillate derived from crude oil, boiling roughly between 180 °C and 360 °C. It is a complex mixture of hydrocarbons, primarily alkanes, cycloalkanes, and aromatic compounds with carbon numbers typically from C₁₀ to C₂₂. The exact composition affects the enthalpy of combustion. For energy calculations, a representative formula like C₁₂H₂₃ is often used, giving a molecular weight of about 167 g/mol.

LHV vs. HHV: Which One to Use?

Two values are quoted for combustion enthalpy:

  • Higher Heating Value (HHV) – water produced during combustion is condensed to liquid, releasing extra heat. For diesel, HHV ≈ 45.6 MJ/kg.
  • Lower Heating Value (LHV) – water remains as vapor, so the latent heat of vaporization is not recovered. For diesel, LHV ≈ 44.8 MJ/kg.

In engines, exhaust gases are hot and water leaves as vapor, so LHV is the realistic energy available. In boiler efficiency tests, HHV is often used because flue gas condensation can be captured. Always check which value a specification uses.

How It Compares to Other Fuels

Diesel has a high energy density, which is why it is used in heavy transport. For context (all LHV, approximate):

  • Diesel: 44.8 MJ/kg, 37.3 MJ/L
  • Gasoline: 43.4 MJ/kg, 31.2 MJ/L (density ~0.72 kg/L)
  • Biodiesel (FAME): ~37.5 MJ/kg (lower because of oxygen content)
  • Natural gas (methane): 50 MJ/kg but only ~0.036 MJ/L at atmospheric pressure
  • Coal (bituminous): 24–30 MJ/kg

Per liter, diesel contains about 12% more energy than gasoline, which is one reason diesel engines often achieve better fuel economy.

Common Misconceptions

“Diesel has a higher energy content than gasoline per kg.” Actually, per kg, diesel is only about 3% higher (44.8 vs 43.4 MJ/kg). The big difference is per liter because diesel is denser. Many people confuse density with energy content.

“The enthalpy of combustion is a fixed number.” It varies with the fuel blend. Winter diesel has more lighter components, slightly lowering the energy per kg. Additives and biodiesel content also change it. The 44.8 MJ/kg is a good average but not universal.

Why It Matters in Real Life

Knowing the enthalpy of combustion helps in:

  • Calculating fuel consumption for a given power output (e.g., a 100 kW generator at 40% efficiency needs 100/0.40 = 250 kW of fuel energy, which is 250/44.8 = 5.58 kg of diesel per hour).
  • Estimating CO₂ emissions: burning 1 kg of diesel produces about 3.16 kg of CO₂ (based on carbon content ~86.4%).
  • Designing fuel tanks: a 1000 km range for a truck that uses 30 L/100 km requires 300 L, which weighs about 250 kg.

For laboratory or engineering work, always use the LHV for engine calculations and HHV for boiler efficiency, and specify which one you used.

Frequently Asked Questions

What is the enthalpy of combustion of diesel in kJ/mol?

Using an average molar mass of 167 g/mol (C₁₂H₂₃), the LHV per mole is 44.8 MJ/kg × 0.167 kg/mol = 7.48 MJ/mol, or 7480 kJ/mol. This is approximate because diesel is a mixture.

How do I convert MJ/kg to BTU/gallon?

First, multiply MJ/kg by the density in kg/L to get MJ/L. Then multiply by 947.817 BTU/MJ and by 3.78541 L/gallon. For diesel at 0.832 kg/L: 44.8 × 0.832 = 37.27 MJ/L; 37.27 × 947.817 = 35,330 BTU/L; × 3.78541 = 133,700 BTU/gallon. This matches the calculator’s output when you enter 1 kg and 1 L (but note the calculator’s BTU output is for the mass you enter, not per gallon).

Why is biodiesel’s enthalpy of combustion lower than diesel’s?

Biodiesel contains oxygen atoms in its ester structure. Oxygen does not contribute to combustion energy, so per kg, biodiesel has less chemical energy (about 37.5 MJ/kg vs 44.8 MJ/kg for diesel). However, biodiesel is denser, so the difference per liter is smaller.

Does the enthalpy of combustion change with temperature?

Yes, slightly. Enthalpy of combustion is measured at a standard state (usually 25 °C). At higher temperatures, the fuel and products have more sensible heat, so the net heat released is slightly lower. The effect is small (less than 1% over a 100 °C range) and usually ignored.

How is the enthalpy of combustion measured?

It is measured using a bomb calorimeter. A known mass of diesel is burned in excess oxygen inside a sealed vessel submerged in water. The temperature rise of the water gives the heat released. The measured value is the HHV; the LHV is calculated by subtracting the latent heat of vaporization of the water produced.

Related

Formula used
in m | Mass of diesel | kg | 1 | 0.001
in v | Volume of diesel | L | 1 | 0.001
in density | Density of diesel | kg/L | 0.832 | 0.7
out lhv_mass | Lower heating value (mass) | MJ/kg | 44.8 | 2
out lhv_volume | Lower heating value (volume) | MJ/L | 44.8 * density | 2
out lhv_btu | Energy (BTU) | BTU | (m * 44.8 * 947.817) | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →