molecalculator

Moles & Molar Mass

Enthalpy of Combustion Equation: A-Level Guide

Calculator No. 01-9799 · Updated · Formula and assumptions shown below

Heat absorbed by water 5,225 J
Moles of fuel burned
0.0109 mol
= Mass of fuel burned ÷ Molar mass of fuel
Enthalpy of combustion
-481.4 kJ/mol
= -(Heat absorbed by water ÷ 1000) ÷ Moles of fuel burned
Mass of fuel burned
0.5 g
Set in the form below
You enter
Mass of fuel burned (g), Molar mass of fuel (g/mol), Mass of water heated (g), Temperature rise (°C)
You get
Heat absorbed by water (J), Moles of fuel burned (mol), Enthalpy of combustion (kJ/mol)
Rounding
0 dp · 4 dp · 1 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The enthalpy of combustion (ΔcHo) is the heat released when one mole of a substance burns completely in oxygen under standard conditions (298 K, 1 bar). In A-level chemistry, you calculate it using the equation ΔcHo = ΣΔfHo(products) − ΣΔfHo(reactants), or from experimental temperature changes using q = mcΔT and then dividing by moles.

Formula

The standard enthalpy of combustion is defined per mole of fuel. The formula used in the calculator is:

ΔcHo = −(q / 1000) / n

where:

  • q = heat absorbed by water = mwater × c × ΔT (in joules)
  • mwater = mass of water heated (g)
  • c = specific heat capacity of water = 4.18 J g−1 K−1
  • ΔT = temperature rise (°C, same as K for a difference)
  • n = moles of fuel burned = mass of fuel / molar mass (mol)
  • The negative sign gives the exothermic value (heat released)

For the theoretical value from formation enthalpies (Hess’s law):

ΔcHo = ΣΔfHo(products) − ΣΔfHo(reactants)

Worked Example

Using the defaults: 0.500 g of ethanol (molar mass 46.07 g/mol) heats 100.0 g of water by 12.5 °C.

  1. Heat absorbed by water: q = 100.0 × 4.18 × 12.5 = 5225 J
  2. Moles of ethanol: n = 0.500 / 46.07 = 0.01085 mol
  3. Enthalpy of combustion: ΔcHo = −(5225 / 1000) / 0.01085 = −481.6 kJ/mol

The calculator gives −481.6 kJ/mol (rounded to 1 decimal). The accepted value for ethanol is −1367 kJ/mol; the large difference is due to heat loss in the simple experiment.

Assumptions

  • All heat from the combustion goes into the water (no heat loss to the surroundings).
  • Water has a constant specific heat capacity of 4.18 J g−1 K−1 over the temperature range.
  • The fuel is pure and burns completely to CO2(g) and H2O(l).
  • Standard conditions: 298 K and 1 bar pressure.

How to Choose the Right Equation

In A-level exams, you’ll see two main routes to ΔcHo:

  • Experimental route: Use q = mcΔT when you have measured a temperature change. This gives the heat transferred, then divide by moles of fuel burned.
  • Hess’s law route: Use ΣΔfHo(products) − ΣΔfHo(reactants) when you have standard formation enthalpies from a data table. This gives the theoretical value.
  • Bond enthalpy route: ΔcH = Σ(bonds broken) − Σ(bonds formed), but this is less accurate because bond enthalpies are averages.

Always check the state symbols: water as liquid (l) gives a more exothermic value than water as gas (g), because the latent heat of vaporization is included in the liquid case.

Common Mistakes and How to Avoid Them

  • Forgetting the negative sign: Combustion is exothermic, so ΔcH is always negative. If you get a positive value, check your arithmetic.
  • Unit mix-ups: q is in joules, but ΔcH is in kJ/mol. Convert before dividing.
  • Using mass of fuel instead of moles: The definition is per mole, so you must divide by moles, not mass.
  • Ignoring heat loss: In a simple calorimeter, a lot of heat escapes. The experimental value is always less exothermic than the theoretical one.
  • Rounding too early: Keep at least 3 significant figures in intermediate steps to avoid error propagation.

Why Experimental Values Differ from Theoretical

The classic A-level experiment (burning a fuel under a beaker of water) gives a ΔcH that is often 30–50% less exothermic than the data-book value. Reasons include:

  • Heat lost to the air, the beaker, and the thermometer.
  • Incomplete combustion (soot, CO, or unburnt fuel).
  • Evaporation of water during the experiment.
  • Not all the fuel is burned – some may drip off or vaporize.

To improve accuracy, use a bomb calorimeter (constant volume), insulate the apparatus, and stir the water to ensure even heating.

Using Hess’s Law for Combustion

Hess’s law states that the enthalpy change for a reaction is the same regardless of the route taken. For combustion, you can use formation enthalpies:

For ethanol (C2H5OH):

ΔcHo = [2×ΔfHo(CO2) + 3×ΔfHo(H2O(l))] − [ΔfHo(C2H5OH) + 3×ΔfHo(O2)]

Since ΔfHo(O2) = 0 (element in its standard state), the equation simplifies.

Using data: ΔfHo(CO2) = −393.5 kJ/mol, ΔfHo(H2O(l)) = −285.8 kJ/mol, ΔfHo(C2H5OH) = −277.7 kJ/mol.

ΔcHo = [2(−393.5) + 3(−285.8)] − [−277.7 + 0] = [−787.0 − 857.4] + 277.7 = −1366.7 kJ/mol.

This matches the accepted value of −1367 kJ/mol.

Frequently Asked Questions

What is the difference between enthalpy of combustion and enthalpy of formation?

Enthalpy of combustion is the heat released when one mole of a substance burns in oxygen. Enthalpy of formation is the heat change when one mole of a compound forms from its elements in their standard states. Formation enthalpies are used as building blocks in Hess’s law calculations; combustion enthalpies are often measured directly.

Why is the enthalpy of combustion always negative?

Combustion reactions release heat because the products (CO2 and H2O) have stronger bonds and lower enthalpy than the reactants. By convention, exothermic reactions have negative ΔH. The only exception would be a substance that requires energy to burn, but that is not a real combustion process.

How do you calculate enthalpy of combustion from bond enthalpies?

Use the formula ΔH = Σ(bond enthalpies of reactants) − Σ(bond enthalpies of products). For ethanol, you’d break all C–C, C–H, C–O, O–H, and O=O bonds, then form C=O and O–H bonds. This method is less accurate because bond enthalpies are average values taken from many compounds.

What are standard conditions for enthalpy of combustion?

Standard conditions are 298 K (25 °C) and 1 bar (100 kPa) pressure. The substance must be in its standard state: for carbon that is graphite, for hydrogen that is H2(g). Water produced is taken as liquid (l), not gas, unless otherwise stated.

Why does my experimental value differ from the data book?

Heat loss to the surroundings, incomplete combustion, and evaporation of water are the main reasons. In a school lab, you might get −500 kJ/mol for ethanol instead of −1367 kJ/mol. Using a bomb calorimeter and insulating the apparatus reduces the error.

Can enthalpy of combustion be used to compare fuels?

Yes, but compare per mole for a fair chemical comparison. For energy per gram (useful for fuels), divide ΔcH by molar mass. For example, hydrogen has a high ΔcH per mole (−286 kJ/mol) but a very high value per gram because its molar mass is only 2 g/mol.

Related

Formula used
in m | Mass of fuel burned | g | 0.500 | 0
in mm | Molar mass of fuel | g/mol | 46.07 | 0.001
in w | Mass of water heated | g | 100.0 | 0
in dt | Temperature rise | °C | 12.5 | 0
out q | Heat absorbed by water | J | w * 4.18 * dt | 0
out n | Moles of fuel burned | mol | m / mm | 4
out dh | Enthalpy of combustion | kJ/mol | -(q / 1000) / n | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →