molecalculator

Moles & Molar Mass

Enthalpy of Solution Equation & How to Use It

Calculator No. 01-9214 · Updated · Formula and assumptions shown below

Molarity 0.2000 mol/L
Concentration in millimolar
200.00 mM
= Molarity × 1000
Mass of solute
2.922 g
Set in the form below
Molar mass
58.44 g/mol
Set in the form below
You enter
Mass of solute (g), Molar mass (g/mol), Final solution volume (mL)
You get
Molarity (mol/L), Concentration in millimolar (mM)
Rounding
4 dp · 2 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The enthalpy of solution (ΔHsol) is the heat absorbed or released when one mole of a solute dissolves in a solvent at constant pressure. The equation is ΔHsol = q / n, where q is the heat exchanged with the surroundings (in joules) and n is the amount of solute dissolved (in moles). This page provides a calculator that determines ΔHsol from the temperature change of the solution, the mass of solution, and its specific heat capacity.

Formula

The enthalpy of solution is defined as the heat change per mole of solute at constant pressure. The general equation is:

ΔHsol = q / n

Where:

  • ΔHsol = enthalpy of solution (kJ/mol or J/mol)
  • q = heat absorbed or released by the solution (J or kJ)
  • n = moles of solute dissolved (mol)

In a typical calorimetry experiment, the heat q is calculated from the temperature change of the solution using:

q = msolution × csolution × ΔT

Where:

  • msolution = mass of the solution (g) – usually the mass of solvent plus solute
  • csolution = specific heat capacity of the solution (J/(g·°C)) – for dilute aqueous solutions, this is approximated as 4.184 J/(g·°C), the value for water
  • ΔT = final temperature − initial temperature (°C or K, the difference is the same)

Combining, the enthalpy of solution is:

ΔHsol = (msolution × csolution × ΔT) / n

If the temperature increases (ΔT > 0), the solution releases heat to the surroundings, so q is negative and ΔHsol is negative (exothermic). If the temperature decreases, ΔHsol is positive (endothermic).

Worked Example

Let’s calculate the molarity and then use it to find the enthalpy of solution for a typical example: dissolving 2.922 g of sodium chloride (NaCl, molar mass 58.44 g/mol) in enough water to make 250 mL of solution.

Step 1: Calculate moles of solute

n = mass / molar mass = 2.922 g / 58.44 g/mol = 0.05000 mol

Step 2: Convert volume to liters

V = 250 mL × (1 L / 1000 mL) = 0.250 L

Step 3: Calculate molarity

M = n / V = 0.05000 mol / 0.250 L = 0.2000 mol/L (0.2000 M)

Step 4: Millimolar concentration

cmM = 0.2000 mol/L × 1000 = 200.0 mM

Now, to find the enthalpy of solution, suppose the temperature of the solution rose by 0.35 °C during the dissolution. The mass of the solution is approximately the mass of water (250 g) plus the mass of solute (2.922 g) = 252.922 g. Using the specific heat of water (4.184 J/(g·°C)):

q = 252.922 g × 4.184 J/(g·°C) × 0.35 °C = 370.4 J

Since the temperature rose, the process is exothermic, so q = −370.4 J (heat released).

ΔHsol = q / n = −370.4 J / 0.05000 mol = −7408 J/mol = −7.41 kJ/mol

The negative sign indicates that dissolving NaCl in water is exothermic (releases heat), which matches the known value of about −3.9 kJ/mol for NaCl at infinite dilution (our simplified example gives a slightly different value because we used a small temperature change and ignored heat capacity of the calorimeter).

Assumptions

  • The solution is dilute enough that the specific heat capacity is close to that of pure water (4.184 J/(g·°C)).
  • The calorimeter absorbs no heat (perfect insulation).
  • The density of the solution is approximately 1 g/mL for dilute aqueous solutions.
  • The dissolution is complete and no chemical reaction other than solvation occurs.
  • The pressure is constant (usually 1 atm).

How to Measure the Enthalpy of Solution in Practice

To measure ΔHsol experimentally, you would use a calorimeter – a well-insulated container with a thermometer. The basic procedure is:

  1. Measure a known volume of solvent (usually water) into the calorimeter and record its initial temperature.
  2. Weigh a known mass of solute (so you can calculate moles).
  3. Add the solute quickly, stir, and record the highest or lowest temperature reached.
  4. Calculate q using the mass of the solution (solvent + solute) and the temperature change.
  5. Divide q by the moles of solute to get ΔHsol.

In a school lab, a simple styrofoam cup calorimeter is often used. In more precise work, a constant-pressure calorimeter or a differential scanning calorimeter is used. Always follow your lab method, the safety data sheet (SDS) and your supervisor.

Why Does the Enthalpy of Solution Vary?

The enthalpy of solution is not a constant for a given solute; it depends on concentration. When you dissolve a solute, the process involves three energy terms:

  • Lattice energy – the energy required to break the ionic or molecular lattice of the solid (endothermic).
  • Solvation energy – the energy released when solute particles are surrounded by solvent molecules (exothermic).
  • Mixing energy – the energy change from the mixing of solute and solvent (often small).

The sum of these gives the overall ΔHsol. For ionic compounds, if the lattice energy is larger than the solvation energy, the process is endothermic (e.g., ammonium nitrate, NH4NO3, which absorbs heat and makes a cold pack). If solvation energy dominates, the process is exothermic (e.g., sodium hydroxide, NaOH, which releases heat).

As you dissolve more solute, the concentration increases, and the enthalpy of solution changes because the solvation environment becomes different. The standard enthalpy of solution (ΔH°sol) is usually reported for infinite dilution – where each solute molecule is fully surrounded by solvent and no solute-solute interactions occur.

Common Mistakes and Misconceptions

  • Forgetting the sign: A temperature increase means heat is released (negative ΔH), even though the solution feels hot. A temperature decrease means heat is absorbed (positive ΔH).
  • Using the wrong mass: The heat equation uses the mass of the entire solution (solvent + solute), not just the solvent. For dilute solutions, the difference is small, but for concentrated solutions it matters.
  • Ignoring the calorimeter heat capacity: In a real experiment, the calorimeter absorbs some heat. For precise work, you must calibrate the calorimeter and add its heat capacity to the calculation.
  • Assuming the specific heat is constant: The specific heat of a solution can differ from that of pure water, especially at high concentrations. For accurate results, use the actual specific heat of the solution if known.
  • Mixing up kJ and J: Always convert to consistent units. If you use J for q and mol for n, the result is in J/mol; divide by 1000 to get kJ/mol.

Enthalpy of Solution vs. Enthalpy of Hydration

These two terms are often confused. The enthalpy of hydration (ΔHhyd) is the heat change when one mole of gaseous ions dissolves in water to form an infinitely dilute solution. It is always exothermic because ion-dipole attractions form. The enthalpy of solution for an ionic compound can be related to the lattice enthalpy (ΔHlattice) and the hydration enthalpy of the ions:

ΔHsol = ΔHlattice + ΔHhyd

Here, ΔHlattice is positive (endothermic – breaking the lattice) and ΔHhyd is negative (exothermic – forming ion-dipole bonds). This is a Born-Haber cycle type relationship. For example, for NaCl, the lattice enthalpy is about +787 kJ/mol and the hydration enthalpy is about −783 kJ/mol, giving a small positive ΔHsol of about +4 kJ/mol (though the actual measured value is slightly exothermic due to concentration effects).

Frequently Asked Questions

What is the difference between enthalpy of solution and enthalpy of dissolution?

They are essentially the same thing. “Enthalpy of solution” is the standard term, but “enthalpy of dissolution” is used interchangeably. Both refer to the heat change when a solute dissolves in a solvent.

Why is the enthalpy of solution sometimes positive and sometimes negative?

It depends on the balance between the energy required to break the solute-solute attractions (lattice energy for ionic compounds) and the energy released when solute-solvent attractions form (solvation energy). If breaking requires more energy than forming, the net is endothermic (positive). If forming releases more, the net is exothermic (negative).

How do I calculate the enthalpy of solution from a temperature change?

Use the equation q = m × c × ΔT, where m is the mass of the solution, c is the specific heat capacity (usually 4.184 J/(g·°C) for water), and ΔT is the temperature change. Then divide q by the moles of solute. Remember to assign the correct sign: if the temperature rises, q is negative.

Does the enthalpy of solution depend on the amount of solvent?

Yes, for a given amount of solute, the enthalpy of solution changes with concentration. At infinite dilution (large excess of solvent), the value approaches a constant called the standard enthalpy of solution. At higher concentrations, solute-solute interactions become significant, so the value changes.

What is the enthalpy of solution of NaCl in water?

The standard enthalpy of solution for NaCl is about +3.9 kJ/mol at infinite dilution (endothermic), but in a typical lab experiment with a few grams in water, it often appears slightly exothermic (around −3 to −4 kJ/mol) because of the heat of dilution and the calorimeter’s heat capacity. The exact value depends on concentration and temperature.

Why do cold packs use ammonium nitrate?

Ammonium nitrate (NH4NO3) has a highly endothermic enthalpy of solution (about +25.7 kJ/mol). When it dissolves in water, it absorbs heat from the surroundings, causing the temperature to drop dramatically. This makes it ideal for instant cold packs.

Related

Formula used
in m | Mass of solute | g | 2.922 | 0
in mm | Molar mass | g/mol | 58.44 | 0.001
in v | Final solution volume | mL | 250 | 0.001
out c | Molarity | mol/L | m / mm / (v / 1000) | 4
out cmm | Concentration in millimolar | mM | c * 1000 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →