molecalculator

Moles & Molar Mass

Equation for k in Chemistry: Rate Constant Formula

Calculator No. 01-4288 · Updated · Formula and assumptions shown below

Rate constant k 0.1600 L/(mol*s)
Reaction rate
0.02 mol/(L*s)
Set in the form below
Concentration of A
0.5 mol/L
Set in the form below
Concentration of B
0.25 mol/L
Set in the form below
You enter
Reaction rate (mol/(L*s)), Concentration of A (mol/L), Concentration of B (mol/L)
You get
Rate constant k (L/(mol*s))
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

In chemical kinetics, the equation for the rate constant k comes from the rate law: for a reaction with rate = k[A]m[B]n, calculate k by dividing the measured rate by the reactant concentrations raised to their experimentally determined orders. Enter the rate and concentrations below to calculate k and its units; this example assumes first-order dependence on A and B.

Formula

For a general rate law, rate = k[A]m[B]n, so k = rate / ([A]m[B]n). Here, rate is the measured reaction rate in mol L−1 s−1; [A] and [B] are reactant concentrations in mol L−1; and m and n are reaction orders, found from experiment. The calculator uses the special case rate = k[A][B], with m = n = 1. Thus k = rate / ([A][B]) and its units are L mol−1 s−1, also written M−1 s−1.

The rate law is not generally obtained by taking coefficients from a balanced overall equation. Reaction orders describe how the measured rate responds to concentration changes and must be established experimentally or provided for the reaction. The equation above assumes the rate is expressed as a positive consumption or formation rate, with a consistent definition across measurements.

Worked Example

Using the calculator defaults, the measured rate is 0.020 mol L−1 s−1, [A] = 0.50 mol L−1, and [B] = 0.25 mol L−1. For first order in each reactant:

  1. Multiply the concentrations: (0.50 mol L−1)(0.25 mol L−1) = 0.125 mol2 L−2.
  2. Divide the rate by that product: k = (0.020 mol L−1 s−1) / (0.125 mol2 L−2) = 0.16 L mol−1 s−1.

The result, to the four decimal places configured for the output, is 0.1600 L/(mol·s). The extra displayed zeros indicate calculator formatting, not extra precision in the measurements.

Assumptions

  • The rate law is first order in A and first order in B; this is an illustrative model, not a universal rule.
  • The rate and concentrations use compatible units, and the concentrations represent the reaction conditions at which the rate was measured.
  • The rate is a valid initial or instantaneous rate for applying the stated rate law; the calculation does not determine reaction orders or account for changing conditions.

What the Rate Constant Means

The rate constant is the proportionality factor connecting a rate law’s concentration terms to the observed reaction rate. At a fixed temperature and for a specified reaction mechanism and medium, a larger k generally corresponds to a faster reaction at the same reactant concentrations. It is not itself the reaction rate: the rate also depends on concentration and on the reaction orders.

The units of k depend on the overall order, which is the sum of the exponents in the rate law. For an overall order q, rate has units of concentration per time, so k has units of (concentration)1−q per time. Examples using concentration in mol/L and time in seconds include:

  • Zero order, rate = k: k has units mol L−1 s−1.
  • First order, rate = k[A]: k has units s−1.
  • Second order, such as rate = k[A][B]: k has units L mol−1 s−1.

Consequently, a numerical value for k is incomplete without its units, rate-law form, and conditions. Values obtained using minutes instead of seconds or mol/L instead of another concentration unit will have different numerical values and corresponding units.

How to Choose the Right Equation

First identify the reaction’s experimentally supported rate law and its order in each reactant. Then insert concentrations and a rate measured under the same conditions. If the rate law is rate = k[A]2, for example, the correct calculation is k = rate/[A]2; the calculator above does not apply because it assumes two distinct, first-order concentration factors.

For an initial-rate method, compare experiments where one reactant concentration changes while the others remain fixed. If doubling [A] doubles the rate, that evidence is consistent with first order in A; if it quadruples the rate, it is consistent with second order. Such comparisons are useful only when measurements are reliable and the other conditions remain comparable. More complex reactions may need a more complete kinetic model.

For a single-reactant first-order process, another common relationship is the integrated rate equation, ln([A]t/[A]0) = −kt. It gives k = ln([A]0/[A]t)/t, where [A]0 and [A]t are concentrations at the start and after elapsed time t. This is a different route: it uses concentration change over time rather than a directly measured rate. The appropriate form depends on the reaction order and the available measurements.

Conditions, Units, and Common Errors

  • Assuming orders from the balanced equation: Overall reaction coefficients do not usually determine the rate law for a multistep reaction. Use measured or supplied orders.
  • Mixing concentration units: Convert all concentrations to a common unit before calculating. A rate in mol L−1 s−1 cannot be combined directly with concentrations entered in mmol/L without conversion.
  • Confusing rate and k: Rate changes as concentrations change; k is the fitted proportionality constant for the chosen rate law and conditions.
  • Ignoring temperature or medium: Rate constants can change substantially with temperature and may depend on solvent, pressure, ionic strength, or other conditions. Do not compare values as if conditions were identical when they are not.
  • Overstating precision: Report k with units and precision justified by the experimental data. Calculator digits do not remove uncertainty in measured rates or concentrations.

For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor. This calculation is a study and data-analysis aid; it does not establish a safe procedure or replace experimental validation.

Frequently Asked Questions

What is the equation for k in chemistry?
For rate = k[A]m[B]n, rearrange to k = rate / ([A]m[B]n). The rate law and its orders must be known.

What does k stand for in a rate law?
k is the rate constant: the factor that relates the rate to reactant concentrations raised to their reaction orders, at specified conditions.

How do I find k from a graph?
It depends on the rate law. For a first-order reaction, a plot of ln[A] against time has slope −k. For a second-order single-reactant reaction, a plot of 1/[A] against time has slope k under the integrated rate-law assumptions.

Can k be negative?
A conventional forward rate constant is nonnegative. A negative slope may appear in a concentration-versus-time graph because a reactant is being consumed; that does not mean k is negative.

Does k change when concentration changes?
For a fixed reaction and fixed conditions, k is treated as independent of reactant concentration in the rate law. The reaction rate itself usually changes with concentration. Temperature or changes in the reaction environment can change k.

Why do rate constants have different units?
The units depend on the overall reaction order. The concentration powers in the rate law must combine with k to give rate units of concentration per time.

Related

Formula used
in rate | Reaction rate | mol/(L*s) | 0.020 | 0
in a | Concentration of A | mol/L | 0.50 | 0
in b | Concentration of B | mol/L | 0.25 | 0
out k | Rate constant k | L/(mol*s) | rate / (a * b) | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →