The linear thermal expansion equation is ΔL = αL₀ΔT: multiply a material’s coefficient of linear expansion by its original length and temperature change to estimate how much its length changes. Enter the material’s coefficient, starting length, and temperature change in the calculator below; it returns the length change and the estimated final length.
Formula
For ordinary linear expansion over a moderate temperature range, the equation is ΔL = αL₀ΔT. The calculator also gives the estimated final length, L = L₀ + ΔL.
- ΔL is the length change, in metres (m).
- α is the material’s linear thermal expansion coefficient, in reciprocal kelvins (K⁻¹). Its numerical value is also commonly expressed per degree Celsius (°C⁻¹), because a temperature interval of 1 K equals an interval of 1 °C.
- L₀ is the original length, in metres.
- ΔT is the temperature change, in kelvins: final temperature minus initial temperature.
- L is the estimated final length, in metres.
Use SI units in the calculator. Convert centimetres to metres by dividing by 100, and millimetres to metres by dividing by 1,000. A positive temperature change normally gives positive expansion; a negative change gives contraction. The coefficient must be appropriate to the material and conditions.
Worked Example
Using the calculator’s default values, α = 0.000012 K⁻¹, L₀ = 1 m, and ΔT = 50 K:
- Calculate the change: ΔL = αL₀ΔT = 0.000012 × 1 × 50 = 0.000600 m.
- Convert the change to millimetres: 0.000600 m × 1,000 mm/m = 0.600 mm.
- Calculate the estimated final length: L = 1 + 0.000600 = 1.000600 m.
The calculator displays the length change as 0.000600 m and final length as 1.000600 m, rounded to six decimal places.
Assumptions
- The material expands uniformly and remains in one phase.
- The coefficient α is treated as constant across the temperature interval.
- The object is free to expand; constraints, joints, and applied loads are not included.
- The calculation estimates a small dimensional change using the linear expansion model.
What Thermal Expansion Means
Most materials change dimensions when their temperature changes. In a solid, heating increases the average vibration of atoms around their positions in the material’s structure. Because the forces between atoms are not perfectly symmetric, the average spacing usually increases. Cooling usually reduces that spacing. The exact response depends on the substance, its structure, and sometimes its direction within a crystal.
The coefficient α expresses the approximate fractional change in length per degree of temperature change. For example, α = 0.000012 K⁻¹ means a one-metre piece changes by about 0.000012 m for a 1 K increase, within the model’s useful range. It is a material property, not a universal constant: look up a value for the particular alloy, glass, polymer, or other material and the relevant temperature range.
Linear, Area, and Volume Expansion
The calculator uses linear expansion, suitable when the quantity of interest is the length of a solid component. Related equations estimate changes in area and volume:
- Area: ΔA ≈ βA₀ΔT, where A₀ is the initial area and β is the area expansion coefficient.
- Volume: ΔV ≈ γV₀ΔT, where V₀ is the initial volume and γ is the volume expansion coefficient.
For an isotropic solid—a material whose properties are the same in every direction—and a small temperature interval, β is approximately 2α and γ approximately 3α. These are approximations, not rules for every material. Liquids are generally described by volume expansion rather than a meaningful fixed length change, and gases require a gas-law treatment that accounts for pressure and other conditions.
How to Choose Inputs and Read the Result
Choose α from a reliable reference for the exact material where possible. Values can differ between grades and may vary with temperature. Use the original length at the initial temperature, not a length already adjusted for the temperature change. Enter ΔT as final temperature minus initial temperature; for example, warming from 20 °C to 70 °C gives ΔT = 50 K. The size of a temperature difference is the same in kelvins and degrees Celsius, so no 273.15 offset is needed for ΔT.
The output is a change in length, not a percentage. To find the percentage change, divide ΔL by L₀ and multiply by 100. In the default example, the fractional change is 0.000600 ÷ 1 = 0.000600, or 0.0600%. A negative result means the length decreases relative to the starting condition.
Limits and Common Mistakes
- Confusing temperature with temperature change: Do not enter an absolute temperature such as 50 °C if the object warmed by 50 °C. Enter the difference between final and initial temperatures.
- Mixing units: If α is in K⁻¹, use a length in metres to get ΔL in metres. Convert the answer afterward if millimetres or another unit is more convenient.
- Assuming every material expands: Most common solids expand when heated, but some substances have unusual behavior over particular ranges. Use material-specific data.
- Ignoring constraints: A rod fixed at both ends cannot freely lengthen. Restraint can create thermal stress; this length-change equation does not calculate that stress.
- Applying a constant coefficient too far: For a broad temperature range, α may vary. More accurate calculations use temperature-dependent data, often integrating the coefficient over the interval.
For small changes, the linear equation is often a useful engineering estimate. It does not account for nonuniform temperature, changes in phase, cracks, composite layers, or geometry that changes substantially. When those effects matter, use a model suited to the actual material and boundary conditions.
Frequently Asked Questions
What is the equation for thermal expansion?
For a change in length, use ΔL = αL₀ΔT. Add the change to the initial length to estimate final length: L = L₀ + ΔL.
What does α mean in the thermal expansion equation?
Alpha is the linear expansion coefficient, usually given in K⁻¹ or °C⁻¹. It describes the approximate fractional change in length per degree of temperature change for a specific material.
Can I use Celsius in the equation?
Yes, if you use a temperature difference in degrees Celsius and α is expressed per degree Celsius. A temperature interval of 1 °C has the same size as 1 K. Do not substitute an absolute Celsius temperature for ΔT.
How do I calculate expansion in millimetres?
Calculate ΔL using consistent units, then convert metres to millimetres by multiplying by 1,000. Alternatively, convert the starting length to metres first and convert the resulting change afterward.
Does thermal expansion depend on the material?
Yes. Different materials have different coefficients, and a material’s coefficient may vary with temperature or composition. Use a value that matches the material and conditions rather than assuming one coefficient fits all substances.
Related
Formula used
in alpha | Linear expansion coefficient | 1/K | 0.000012 | 0 in length | Original length | m | 1 | 0 in temp | Temperature change | K | 50 | -273.15 out change | Length change | m | alpha * length * temp | 6 out final | Final length | m | length + change | 6
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Gas Correction Factor Calculator and Table1.2534
- Gas Correction Factor Formula and Calculator0.9829
- Gas Temperature: Calculate It from Pressure and Volume298.15 K
- Gas Correction Factor Calculator: Formula and Uses107.322 same as input
- Gas Cv Calculator: Heat Capacity Ratio and Formula20.786 J/(mol·K)
- Density Temperature Correction Calculator and Formula999.25 kg/m^3