molecalculator

Moles & Molar Mass

Equation for Total Enthalpy: H = U + pV Explained

Calculator No. 01-9278 · Updated · Formula and assumptions shown below

Enthalpy change (ΔH) 10,460 J
Enthalpy change (ΔH)
10.460 kJ
= Enthalpy change (ΔH) ÷ 1000
Mass of substance
100 g
Set in the form below
Specific heat capacity
4.184 J/(g·°C)
Set in the form below
You enter
Mass of substance (g), Specific heat capacity (J/(g·°C)), Temperature change (ΔT) (°C)
You get
Enthalpy change (ΔH) (J), Enthalpy change (ΔH) (kJ)
Rounding
0 dp · 3 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

The total enthalpy of a system is given by the equation H = U + pV, where H is enthalpy, U is internal energy, p is pressure, and V is volume. In practical thermodynamics, what you almost always calculate is the change in enthalpy (ΔH), which equals the heat exchanged at constant pressure. This page provides a calculator for the enthalpy change of a substance given its mass, specific heat capacity, and temperature change, then explains the full context of the H = U + pV definition.

Formula

The defining equation for total enthalpy is:

H = U + pV

  • H = total enthalpy (J)
  • U = internal energy of the system (J)
  • p = absolute pressure (Pa or N/m²)
  • V = volume of the system (m³)

For a process at constant pressure, the change in enthalpy is:

ΔH = ΔU + pΔV

And for a simple heating or cooling process (no phase change, no chemical reaction, constant pressure), the enthalpy change is:

ΔH = m · c · ΔT

  • m = mass of the substance (g)
  • c = specific heat capacity (J/(g·°C))
  • ΔT = final temperature − initial temperature (°C)

Note that the calculator above uses the latter formula, which is the most common practical use of enthalpy in lab work.

Worked Example

Using the default values from the calculator: 100 g of water (specific heat capacity 4.184 J/(g·°C)) is heated by 25 °C.

Step 1: Write the formula: ΔH = m · c · ΔT

Step 2: Substitute the values: ΔH = 100 g × 4.184 J/(g·°C) × 25 °C

Step 3: Multiply: 100 × 4.184 = 418.4; then 418.4 × 25 = 10,460 J

Step 4: Convert to kJ: 10,460 J ÷ 1000 = 10.46 kJ

The calculator gives ΔH = 10,460 J (or 10.460 kJ), matching our hand calculation.

Assumptions

  • Constant pressure process (typical for open lab containers).
  • No phase change (solid ↔ liquid ↔ gas) during the temperature change.
  • Specific heat capacity is constant over the temperature range.
  • No chemical reaction or mixing occurs.
  • The system is closed (no mass enters or leaves).

Why Enthalpy Matters

Enthalpy is a state function, meaning its value depends only on the current state of the system, not on how it got there. This makes it incredibly useful because you can calculate ΔH for a reaction using tabulated standard enthalpies of formation, without needing to perform the reaction yourself. In chemistry, the enthalpy change of a reaction (ΔHrxn) tells you whether a process is exothermic (releases heat, ΔH < 0) or endothermic (absorbs heat, ΔH > 0). This is the basis for calorimetry, Hess’s law, and bond energy calculations.

How to Read the Result

The calculator returns the enthalpy change in joules and kilojoules. A positive value means the substance absorbed heat from the surroundings (endothermic). A negative value means it released heat (exothermic). For example, heating 100 g of water by 25 °C requires 10.46 kJ of energy input. If you were cooling the water by 25 °C, the result would be −10.46 kJ, indicating that 10.46 kJ of heat must be removed.

When comparing results, always check the sign and the units. A common error is to report ΔH in J when the question expects kJ, or vice versa. The calculator gives both, so you can use whichever is appropriate.

Common Mistakes

  • Confusing ΔH with ΔU: At constant pressure, ΔH = qp (heat at constant pressure). At constant volume, ΔH = ΔU + VΔp, which is different. Most lab reactions are at constant pressure, so ΔH is the right choice.
  • Using the wrong specific heat capacity: Water has a specific heat of 4.184 J/(g·°C), but metals like copper have about 0.385 J/(g·°C). Always use the value for the specific substance and phase.
  • Forgetting to convert units: If mass is in kg and specific heat is in J/(g·°C), you must convert mass to grams or specific heat to J/(kg·°C). The calculator handles this if you enter consistent units.
  • Ignoring phase changes: The formula ΔH = m·c·ΔT only works within a single phase. Melting ice requires latent heat (334 J/g) in addition to the sensible heat.
  • Using temperature in Kelvin for ΔT: Since ΔT is a difference, Celsius and Kelvin are interchangeable (a change of 1 °C = a change of 1 K). But absolute temperatures in the H = U + pV equation must be in Kelvin.

Limits of the Formula

The simple ΔH = m·c·ΔT formula assumes constant pressure, no phase change, and constant specific heat. For large temperature ranges, specific heat varies with temperature, so you would need to integrate c(T) dT. For chemical reactions, the enthalpy change includes bond breaking and forming, not just sensible heat. The full H = U + pV definition applies to any system, but calculating U from first principles requires statistical mechanics or equations of state. In practice, you use tabulated standard enthalpies of formation (ΔHf°) at 25 °C and 1 atm, then apply Hess’s law to find reaction enthalpies.

Frequently Asked Questions

What is the difference between enthalpy and internal energy?

Internal energy (U) is the total energy stored in the system (kinetic + potential of molecules). Enthalpy (H) adds the pV term, which accounts for the work done to displace the surroundings. At constant pressure, the heat absorbed equals ΔH, not ΔU, because some energy goes into expansion work. For solids and liquids, pV is small, so H ≈ U; for gases, the difference can be significant.

Why do we use enthalpy instead of internal energy?

Because most chemical reactions and lab processes occur at constant atmospheric pressure. Under those conditions, the heat measured by a calorimeter equals ΔH, making it directly measurable. Internal energy changes are harder to measure because they require constant volume conditions (a bomb calorimeter).

Can enthalpy be negative?

Yes, enthalpy changes (ΔH) can be negative for exothermic processes (heat released). However, absolute enthalpy (H) cannot be measured on an absolute scale; only changes are meaningful. Standard enthalpies of formation are defined relative to elements in their standard states, which are assigned a value of zero.

How do I calculate ΔH for a chemical reaction?

Use Hess’s law: ΔHrxn = Σ(ΔHf° of products) − Σ(ΔHf° of reactants), multiplying each by its stoichiometric coefficient. For example, for 2H₂ + O₂ → 2H₂O, you would use the standard enthalpies of formation of H₂O (liquid, −285.8 kJ/mol) and subtract the zero values for the elements.

What is the standard enthalpy of formation?

The standard enthalpy of formation (ΔHf°) is the enthalpy change when one mole of a compound is formed from its elements in their standard states (usually 25 °C and 1 atm). Elements in their standard states have ΔHf° = 0. These values are tabulated in chemistry reference books and are used to calculate reaction enthalpies.

Does the calculator work for gases?

The calculator works for any substance as long as you enter the correct specific heat capacity and no phase change occurs. For gases, specific heat depends on whether the process is at constant pressure (cp) or constant volume (cv). Since enthalpy is defined at constant pressure, use cp (for air, about 1.005 J/(g·°C)).

Practical Safety Note

When performing calorimetry or heating experiments in the lab, always follow your lab method, the safety data sheet (SDS), and your supervisor’s instructions. Use appropriate personal protective equipment, and be aware that exothermic reactions can cause rapid temperature increases or splashing.

Related

Formula used
in m | Mass of substance | g | 100 | 0
in c | Specific heat capacity | J/(g·°C) | 4.184 | 0
in dt | Temperature change (ΔT) | °C | 25 | -273.15
out dh | Enthalpy change (ΔH) | J | m * c * dt | 0
out dkj | Enthalpy change (ΔH) | kJ | dh / 1000 | 3

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →