This calculator compares first-order and zero-order reaction rates over time: enter the initial concentration, rate constant, and elapsed time to calculate the remaining concentration for each model. The results show how the two kinetic orders differ and help you check which model may fit a measured reaction.
Formula
For first-order kinetics, concentration falls in proportion to the concentration remaining: C(t) = C0e−k1t. For zero-order kinetics, concentration falls at a constant rate: C(t) = C0 − k0t, until the reactant is exhausted. The calculator reports zero rather than a negative concentration after that point.
- C(t) is concentration at time t, in mol/L.
- C0 is initial concentration, in mol/L.
- k1 is the first-order rate constant, in s−1.
- k0 is the zero-order rate constant, in mol/(L·s).
- t is elapsed time, in seconds.
The expressions assume time and rate constants use the stated matching units. For example, a first-order constant in min−1 requires time in minutes; convert before entering values. The exponential function uses a dimensionless exponent, so k1t must have no units.
Worked Example
Using the defaults, C0 = 1 mol/L, k1 = 0.01 s−1, k0 = 0.001 mol/(L·s), and t = 60 s.
First order: C(t) = 1 × e−0.01 × 60 = e−0.6 = 0.5488 mol/L (rounded to four decimal places).
Zero order: C(t) = max(0, 1 − 0.001 × 60) = 0.9400 mol/L.
Assumptions
- Each calculation treats its rate constant as fixed over the interval.
- The first-order model applies to a single reactant or an effective rate law that is first order in the measured concentration.
- The zero-order model applies only while its mechanism or limiting conditions sustain a constant rate; the calculator clamps the result at zero after depletion.
- Concentration is used as the measured quantity; changes in volume, temperature, or other conditions are not modeled.
What First- and Zero-Order Mean
Reaction order describes how the rate depends on reactant concentration in an experimentally determined rate law. A first-order disappearance law is −dC/dt = k1C. When concentration doubles, the instantaneous rate doubles, provided other conditions remain unchanged. Integration gives the exponential equation above.
A zero-order law is −dC/dt = k0. Its rate does not depend on the measured reactant concentration across the range where the law holds. Integration gives a straight-line decline in concentration with time. This behavior can occur when a catalyst or surface is saturated, or when another process controls the rate. It should not be assumed to continue after the reactant or relevant capacity is depleted.
Order is not simply a label inferred from a balanced chemical equation. For an elementary reaction step, stoichiometry can relate to the rate law; for an overall multistep reaction, the rate law usually must be established experimentally. A “zero-order reaction” therefore means the observed rate is independent of a specified concentration within a defined set of conditions, not that the reaction has no mechanism or no dependence on anything.
How to Compare the Models
At the same initial concentration and elapsed time, this calculator evaluates both equations with separate rate constants. The numbers are illustrative unless each constant was measured for the actual reaction under the same conditions. A fair comparison requires consistent units, temperature, solvent or medium, and definition of the measured species.
- First order gives a constant half-life: t1/2 = ln(2)/k1, independent of starting concentration under the model.
- Zero order reaches depletion after tdepletion = C0/k0; its half-life is C0/(2k0) and depends on the starting concentration.
- For first order, plotting ln(C) against time should give a straight line with slope −k1. For zero order, plotting C against time should give a straight line with slope −k0.
These plots are diagnostic rather than proof. Measurement error, a limited time range, changing conditions, or multiple reaction steps can make different models appear similar. Compare residuals and consider plausible mechanisms rather than choosing a model from one point or a visually appealing graph alone.
Choosing and Interpreting Rate Constants
Use a first-order constant when data support a rate proportional to the concentration being followed. Use a zero-order constant when the observed rate is approximately constant over the relevant concentration range. Estimate constants from time-series data or a validated method; they are not universal properties of a substance alone. Temperature, catalyst, solvent, pressure, and mechanism can change them.
Units offer a useful check: first-order k has units of inverse time, while zero-order k has concentration per time. If a reported constant has incompatible units, verify the reaction order and any conversion from absorbance, mass, or another measurement to concentration. Avoid extrapolating a fitted zero-order line beyond depletion or beyond the range where constant-rate behavior was observed.
Common Misconceptions and Limits
“Zero order” does not mean zero reaction rate. It means the rate is independent of the relevant concentration under specified conditions; k0 can be positive and substantial. Likewise, first order does not mean a reaction consumes one molecule in a single step. It describes the concentration dependence in the rate law.
The zero-order expression becomes physically invalid if it predicts negative concentration, which is why the calculator displays zero after its linear prediction passes depletion. In practice, a real system may change behavior before that point. The first-order equation approaches zero asymptotically and does not reach exactly zero at a finite time, although concentrations can fall below detection limits.
Neither model accounts for reversible reactions, product inhibition, changing volume, multiple reactants with changing concentrations, or temperature drift unless those effects are incorporated separately. These equations are useful idealized models, not a substitute for collecting data across the conditions of interest. For bench work, follow your lab method, the safety data sheet (SDS), and your supervisor.
Frequently Asked Questions
What is the main difference between first- and zero-order kinetics?
In first-order kinetics, the rate is proportional to the reactant concentration. In zero-order kinetics, the rate is constant with respect to that concentration over the range where the model applies.
Which order has a constant half-life?
First-order kinetics has a concentration-independent half-life, ln(2)/k1. A zero-order half-life depends on the initial concentration: C0/(2k0).
Can concentration be negative in a zero-order equation?
No. A negative result signals that the linear model has been extrapolated past depletion. This calculator returns zero in that case; the actual reaction may change rate as it approaches depletion.
How can I tell whether a reaction is first order or zero order?
Measure concentration at multiple times under controlled conditions. A linear ln(C)-versus-time plot supports first order, while a linear C-versus-time plot supports zero order. Evaluate the fit and experimental uncertainty rather than relying on one observation.
Can reaction order be determined from the balanced equation?
Not generally. The order of an overall reaction is usually established from experimental rate data. Stoichiometric coefficients determine orders only in suitable elementary-step rate laws, not automatically for a multistep overall reaction.
Related
Formula used
in c0 | Initial concentration | mol/L | 1 | 0 in k1 | First-order rate constant | 1/s | 0.01 | 0 in k0 | Zero-order rate constant | mol/(L·s) | 0.001 | 0 in t | Elapsed time | s | 60 | 0 out c1 | First-order concentration | mol/L | c0 * exp(-k1 * t) | 4 out c0t | Zero-order concentration | mol/L | max(0, c0 - k0 * t) | 4
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.
More in this section
- Serial Dilution Calculation Examples0.2000 mol/L
- Serial Dilution: How It Works & Why It Matters1.000 × 10−5 mol/L
- Serial vs Simple Dilution: Key Differences0.2000 mol/L
- Serial Dilution A Level Biology: How To Do It30
- Milton Tablet Dilution: Mixing Guide0.2000 mol/L
- qPCR Serial Dilution Standard Curve: How to Build One100,000 copies/µL