molecalculator

Moles & Molar Mass

First-Order Kinetic Model: Formula and Example

Calculator No. 01-6534 · Updated · Formula and assumptions shown below

First-order rate constant 0.0069 1/s
Half-life
100.0000 s
Result, rounded to 4 decimal places
Fraction remaining
0.5000
= Concentration at time t ÷ Initial concentration
Initial concentration
1 mol/L
Set in the form below
You enter
Initial concentration (mol/L), Concentration at time t (mol/L), Elapsed time (s)
You get
First-order rate constant (1/s), Half-life (s), Fraction remaining
Rounding
4 dp

For study and lab planning. The result follows from the numbers you enter and the formula shown. Check it against your method before you weigh, mix or dilute anything, follow the safety data sheet and your supervisor, and do not use it for clinical, dosing or medication work.

A first-order kinetic model describes a process in which the rate is proportional to the amount of reactant remaining. This calculator estimates the rate constant, half-life, or remaining concentration from first-order data; enter the quantities for the calculation you need and it returns the corresponding result.

Formula

For a first-order process, concentration changes according to the integrated rate law ln(Ct/C0) = −kt, or equivalently Ct = C0e−kt. Rearranging gives the calculator’s first output: k = ln(C0/Ct)/t.

  • C0 is the starting concentration, in mol/L.
  • Ct is the concentration after elapsed time, in mol/L.
  • t is elapsed time, in seconds.
  • k is the first-order rate constant, here in s−1.
  • Half-life is t1/2 = ln(2)/k.
  • Fraction remaining is Ct/C0, a dimensionless ratio.

The calculator assumes C0 and Ct are positive and use the same concentration units. Time must be positive to calculate k; the example uses 100 seconds. A measured concentration equal to or above the initial concentration is not consistent with ordinary decay under this model, and the resulting calculated k will be zero or negative rather than a positive decay constant. Convert time units consistently: if time is entered in minutes instead, the resulting rate constant is in min−1.

Worked Example

Use the exact defaults: C0 = 1 mol/L, Ct = 0.5 mol/L, and t = 100 s.

  1. Calculate the rate constant: k = ln(1 mol/L ÷ 0.5 mol/L) ÷ 100 s = ln(2) ÷ 100 s ≈ 0.0069315 s−1. Displayed to four decimal places: 0.0069 s−1.
  2. Calculate half-life using the unrounded rate constant: t1/2 = 0.69314718 ÷ 0.0069314718 s−1 = 100 s. Displayed to four decimal places: 100.0000 s.
  3. Calculate the fraction remaining: Ct/C0 = 0.5 mol/L ÷ 1 mol/L = 0.5. Displayed to four decimal places: 0.5000.

Assumptions

  • The concentration of the modeled reactant follows a single first-order rate law over the time interval.
  • The concentration values are measured on the same basis and are greater than zero.
  • The entered elapsed time is positive; the rate constant is expressed per second because time is entered in seconds.
  • The model does not itself establish a reaction mechanism or account for changing conditions.

What First-Order Kinetics Means

A reaction rate is a change in concentration per unit time. For a first-order disappearance process, the differential rate law is −dC/dt = kC: at any instant, doubling the reactant concentration doubles its rate of disappearance, if the conditions and rate constant remain unchanged. Integrating this relation produces the exponential concentration-time equation above.

“First order” refers to the exponent on the concentration term in the rate law, not necessarily to the number of reactant molecules in a single elementary collision. A multistep reaction can have an experimentally observed first-order rate law, and reaction order should generally be established from data rather than inferred from the balanced equation alone.

The model is widely useful for processes such as radioactive decay and many dilute-solution reactions under fixed conditions. It also describes disappearance of a substance when its loss rate is proportional to its current amount. It is not a universal description: changing temperature, catalysts, competing pathways, or concentration-dependent mechanisms can make the apparent rate constant change.

How to Use and Interpret the Calculator

Enter a starting concentration, a later concentration, and the time between those measurements. The result is an average model estimate of k over that interval, not a direct measurement at every instant. The half-life output is the time the fitted first-order model predicts for the concentration to fall by half. The fraction output tells what share of the starting concentration remains at the entered time.

For instance, a fraction of 0.5 means 50% remains and 50% has disappeared, assuming a closed accounting of the modeled reactant. A fraction of 0.1 means 10% remains. Do not confuse fraction remaining with percentage: multiply the fraction by 100 to express it as a percent.

For measurements from several time points, a common check is to plot ln(C) against time. A straight line supports first-order behavior over the tested range; its slope is −k. A single pair of concentrations always produces a numerical estimate, but cannot show whether first-order kinetics is actually a good fit. Use multiple measurements, account for measurement uncertainty, and inspect whether the trend is approximately linear.

Common Mistakes and Model Limits

  • Mixing time units: k has inverse-time units. A value in s−1 cannot be used directly with time in hours; convert one consistently.
  • Using incompatible concentration units: C0 and Ct may both be in mol/L or both in another unit, because their ratio cancels units. They must not use different units.
  • Rounding too early: keep extra digits in k when calculating half-life or predicting concentrations. Round only the displayed final result.
  • Treating a negative k as ordinary decay: if Ct exceeds C0, the calculation gives a negative value. This can indicate formation, noisy data, mismatched samples, or an unsuitable decay model.
  • Assuming every reaction has a fixed half-life: a constant half-life follows from a constant first-order k. Other kinetic orders do not generally have a concentration-independent half-life.

The calculator does not determine the reaction order, explain a mechanism, or correct for temperature, sampling losses, background signal, or measurement error. Its answer is only as meaningful as the data and the model assumptions. For bench work, follow your lab method, the safety data sheet (SDS) and your supervisor.

Frequently Asked Questions

What is a first-order kinetic model?
A model where the rate of change is proportional to the current concentration of the reactant. For disappearance, concentration falls exponentially with time.

What is the equation for first-order kinetics?
The integrated form is ln(Ct/C0) = −kt, or Ct = C0e−kt. Here k is the rate constant and t is elapsed time.

What are the units of a first-order rate constant?
They are inverse time, such as s−1, min−1, or h−1. The chosen unit depends on the time unit used in the rate calculation.

How do you calculate the half-life?
For a first-order process, divide ln(2), approximately 0.693147, by k: t1/2 = 0.693147/k. The half-life is independent of the starting concentration when k remains constant.

Does a straight line prove a reaction is first order?
No. A linear plot of ln(concentration) against time is evidence consistent with first-order kinetics over the measured range, but data quality, uncertainty, and alternative models should also be considered.

Related

Formula used
in c0 | Initial concentration | mol/L | 1 | 0
in ct | Concentration at time t | mol/L | 0.5 | 0
in t | Elapsed time | s | 100 | 0
out k | First-order rate constant | 1/s | ln(c0 / ct) / t | 4
out half | Half-life | s | ln(2) / k | 4
out frac | Fraction remaining | - | ct / c0 | 4

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation with the constants and conversion factors written on the page, rounded as each result states. See method and constants, the disclaimer or report an error.

More in this section

The whole Moles & Molar Mass section →